P516-270 CO-100 OFFLINE LOCK USER GUIDE INSTRUCTIONS FOR CO-SERIES OFFLINE LOCKS Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support.
CO-100 Offline Lock User Guide CONTENTS Overview........................................................................................................................................ 3 Getting Started .............................................................................................................................. 4 Construction Access Mode ............................................................................................................ 4 Manual Lock Programming ...................
CO-100 Offline Lock User Guide OVERVIEW The Schlage CO-100 is a keypad-only off-line electronic lock in the CO-Series product line. • Two factory-configured functions are available: 1) Classroom/Storeroom, and 2) Office. • The lock is powered by four (4) AA batteries. See Batteries on page 11 for more information. • Outside lever is normally locked. • Inside lever always allows egress.
CO-100 Offline Lock User Guide GETTING STARTED Follow these steps when setting up a new lock. 1. Install the lock. See the installation guide that came with the lock, or visit www.schlage.com/support, for more information. 2. Test the lock for proper mechanical and electronic operation. See Test Lock Operation on page 8 for more information. 3. When ready to set up for normal use, enter a new programming code, then program the user credentials. See Manual Lock Programming on page 5 for more information. 4.
CO-100 Offline Lock User Guide MANUAL LOCK PROGRAMMING Right LED Left LED Credential Types Credential Type Programming Normal Use Toggle Freeze Pass-Through Function Used to program the lock – does not unlock the lock Unlocks the lock momentarily Changes the state of the lock unless in Freeze state Maintains the lock in current state until Freeze PIN is entered again Unlocks a lock momentarily, regardless of state Description Default PIN Five-digit code 97531 and PIN (3 - 6 digits) 13579 and PIN
CO-100 Offline Lock User Guide Manual Programming Commands Commands are confirmed by five alternating green blinks of the Schlage button. Programming mode will time out if no entry is made in 20-25 seconds. Timeout is indicated by red blinks of the Schlage button, three left and nine right at the same time. The right LED on the Schlage button will blink green to indicate an incorrect entry. To interpret blink patterns, refer to Error Codes on page 7.
CO-100 Offline Lock User Guide Manual Programming Commands Commands are confirmed by five alternating green blinks of the Schlage button. Programming mode will time out if no entry is made in 20-25 seconds. Timeout is indicated by red blinks of the Schlage button, three left and nine right at the same time. The right LED on the Schlage button will blink green to indicate an incorrect entry. To interpret blink patterns, refer to Error Codes on page 7.
CO-100 Offline Lock User Guide TEST LOCK OPERATION If you encounter problems while performing any of the following tests, review the installation guide and correct any problems. Mechanical Test 1. Rotate the inside lever or depress the push bar to open the door. Operation should be smooth, and the latch should retract. 2. Insert the key into the keyway and rotate the key and the outside lever to open the door. Operation should be smooth, and the latch should retract. Electronic Test 1.
CO-100 Offline Lock User Guide LOCK STATUS REPORTS Follow the steps below to obtain lock status reports: Lock status reporting is available with firmware version 2.5.0 or higher. The left and right Schlage button LEDs will blink red once with each button press, followed by the status indicator as described below.
CO-100 Offline Lock User Guide RESET TO FACTORY DEFAULTS ! ! ! All information in the main controller in the lock will be deleted and reset to factory defaults! Main controller configurations that will reset to factory default include: programming and user codes. The door must be locked (not toggled open or in the middle of normal access) before resetting to factory defaults. Follow these steps to reset to factory defaults. 1. Remove the top inside cover. 2.
CO-100 Offline Lock User Guide BATTERIES To Install or Replace Alkaline Batteries Changing batteries does not affect any programmed data. 1. Remove the battery cover. 2. Remove the battery bracket. ! Do not allow the battery pack to hang from the wires. 3. Install the new batteries (install only new AA Alkaline batteries). Make sure the batteries are installed in the correct orientation. 4. Reinstall the battery pack and battery bracket. 5.
CO-100 Offline Lock User Guide LED REFERENCE Schlage Button Condition Access denied Valid PIN entered while lock in Freeze mode Factory default reset Low battery indicator, AA batteries Momentary unsecured access Lights 2 red blinks 12 red blinks indicating lockout One-second solid green with one-second beep 9 left red blinks 1 green blink, then one red blink on relock Optional Inside Push Button (IPB) Action Lights Office Mode Press IPB to lock Press IPB to unlock 1 1 red blink 1 green blink 1 Unloc