Real Security Sets You Free.
® Real Security Sets You Free. ™ Rekeying is easy with Schlage Schlage engineers its locks for professional-grade durability, remarkable beauty and easy rekeying steps. Whether you’re rekeying a lockset or deadbolt, Schlage makes it simple with step-by-step instructions and pictures to help you complete the job. It’s just one more reason that Schlage is the number one selling retail brand.
Rekeying Kits ® Real Security Sets You Free. ™ Schlage Keying Kits provide everything you need to get the job done. Keying Kit 40-1 Includes everything you need to rekey the most popular Schlage knobs, levers and BSeries deadbolts. Includes bottom pins, top pins, springs, cylinder caps, cap pins, cap pin springs, B-Series deadbolt tailpieces, key gauge, plug follower and cap removal tool. Keying Kit 40-1 4 Contains all of the basic materials to rekey most Schlage knobs and levers.
Rekeying Kits – continued Supplemental Keypad Lock ReKeying Kit 8-0 0 Contains all of the basic replacement materials for rekeying Schlage keypad locks and deadbolts. Includes cylinder driver bar, extra screws, tailpiece washers, spacers, and retainers. 4 ® Real Security Sets You Free.
® Real Security Sets You Free.
F, FA & FB-Series – continued ® Real Security Sets You Free. ™ 1 Lock Disassembly 1A 1B B Depress knob/lever A Insert key into knob 1E D Rotate key back 90° to original position and remove key. C Use your thumb and catch using tab on key gauge and pull knob/ lever off of knob catch. or lever cylinder plug, rotate 90°. 1D 1C forefinger to apply pressure on the rose and pull knob/lever off spindle. 1F E To remove the cylinder, first ensure that the keyway on the plug is facing upright.
® Real Security Sets You Free. ™ F, FA & FB-Series – continued Cylinder Removal CAUTION: To REMovE ThE CyLINDER ThRoUGh ThE REAR oF ThE KNoB/LEvER, yoU WILL NoT NEED To USE MoRE ThAN 5 PoUNDS oF FoRCE (oR ThE AMoUNT oF FoRCE REqUIRED To PUSh AN ELEvAToR BUTToN). IF yoU REqUIRE MoRE FoRCE, ThE CyLINDER IS NoT ALIGNED CoRRECTLy FoR REMovAL. PLEASE REFER To STEPS E AND F FoR CoRRECT ALIGNMENT.
F, FA & FB-Series – continued ® Real Security Sets You Free. ™ Cylinder Repinning - Method 1 Method 1: (RECoMMEnDED) B A B Insert & rotate the key 90° A Using U-Shaped and insert the end of the plug follower into the rear of the cylinder housing - pushing the plug out the front of the housing. portion of key gauge, press forward to remove C-Clip cylinder retaining ring. C D C Keep the plug follower in the body to keep the top pins and springs from blowing.
® F, FA & FB-Series – continued Real Security Sets You Free. ™ Cylinder Repinning - Method Method : The compressible cylinders can also be rekeyed from the top of the cylinder by removing the stainless steel cap – and dumping the bottom pins, top T-Pins, and top springs from the cylinder. To rekey, simply insert new bottom pins into the holes on the top of the cylinder and then re-insert the top T-pins and springs on top of the bottom pins.
F, FA & FB-Series – continued ® Real Security Sets You Free. ™ 4 Lock Reassembly 4A 4C 4B A Compress the cap and reinsert the cylinder into the shank of the knob (plug face first) aligning the cap with the slot in the sleeve inside the knob. 4D D If necessary, depress knob catch and slide knob on until the catch pops into the slot on knob. Rotate key 90° and remove key. 10 B With the cap aligned with the slot, push the cylinder the rest of the way into the knob.
Real Security Sets You Free.
BE & FE Electronic Series – continued Real Security Sets You Free. ™ 1 Keypad Lock Cylinder Removal 1A 1B FE and FE cylinder removal instructions 1C B Remove cylinder A Remove access panel from keypad assembly. C Remove cylinder cap, retaining screw and cylinder. washer, tailpiece, pin, and spring. Remove the Cylinder Plug A B A Insert key and turn clockwise to two o’clock position. Place flat end of follower against back of cylinder plug.
BE & FE Electronic Series – continued Real Security Sets You Free. ™ Load new Bottom Pins A B A Use numbers on key bow IMPoRTANT! MAKE SURE ThAT ALL PINS ARE FLUSh WITh ToP oF PLUG, FoRMING A PERFECT ShEAR LINE. IF ANy ExTEND ABovE oR BELoW ThE SURFACE, REPLACE WITh CoRRECT SIzES. B Load new bottom pins or use key gauge (see page 38) to determine new key combination. Insert new key all the way until it stops against plug face.
BE & FE Electronic Series – continued Real Security Sets You Free. ™ 1 Keypad Deadbolt Cylinder Removal 1A 1B A Remove backplate from outside keypad assembly. 1D D Remove cylinder cap, tailpiece, pin, and spring. 14 BE cylinder removal instructions 1C B Remove cylinder from thumbturn. C Remove retainer, block, and disc from cylinder.
BE & FE Electronic Series – continued Real Security Sets You Free. ™ Remove the Cylinder Plug A B A Insert key and turn C B CAUTION: To avoid top pins clockwise to two o’clock position. Place flat end of follower against back of cylinder plug. springing out of cylinder shell, push follower all the way through in one careful, continuous motion. When completed, shell should be near center of follower. C Dump bottom pins from plug and remove old key. Discard old pins and keys.
BE & FE Electronic Series – continued Real Security Sets You Free. ™ 4 Keypad Deadbolt Reassembly - cont. 4A BE cylinder removal instructions 4B A Install spring, pin tailpiece, and cylinder cap. B Install disc, block, and retainer. 4C C Reinstall cylinder as shown. NOTE: MAKE SURE ToP oF CyLINDER IS PoINTING ToWARDS KEyPAD. D Use BE365 Installation Sheet to Install Lock.
® Real Security Sets You Free.
A & AL Medium Duty Series – continued ® Real Security Sets You Free. ™ 1 Remove the Knob or Lever 1A 1B A Put key into cylinder 1C B Using tab on key (with teeth of key facing up) and turn key clockwise one quarter turn to three o’clock position. gauge, depress knob/ lever retainer through hole in knob/lever shank. B A A Push cylinder forward B Remove key from cylinder and until knob sleeve disengages from back of knob. Remove sleeve and set it aside.
® A & AL Medium Duty Series – continued Real Security Sets You Free. ™ 4 Remove the Cylinder Plug 4A 4B A Insert key and turn 4C B hold follower firmly against plug and clockwise to two o’clock position. hold slotted end of follower against back of cylinder plug. carefully slide it through cylinder shell until plug and front of follower have passed completely through cylinder shell. IMPORTANT! Do NoT PULL FoLLoWER CoMPLETELy ThRoUGh CyLINDER. Cylinder shell should end up near center of follower.
A & AL Medium Duty Series – continued ® Real Security Sets You Free. ™ Reinsert the Cylinder Plug A B A Engage back of plug in follower notch and turn slightly relative to cylinder shell. Gently push plug into shell, pushing follower out. Reassemble the Knob A B Reattach retaining clip to back of cylinder and snap into place. IMPORTANT: KEy IS STILL IN PLUG AT ThIS PoINT! REMovE KEy oNLy WhEN “C” CLIP IS SNAPPED BACK INTo PLACE.
Real Security Sets You Free.
B 00 & BA 00-Series – continued Real Security Sets You Free. ™ 1 Preparation REtA t inER tA CRAnK 1A 1B A Remove adapter ring (For 1C B Lift crank assembly and 1½˝ opening only). Place cylinder assembly face down on smooth surface. retainer over bumps with flat blade screwdriver and remove. Remove the Cylinder Cap A B A Engage teeth of cylinder cap removal tool with scallops in cylinder cap as shown. Push tool down against slight spring pressure and unscrew cap.
B 00 & BA 00-Series – continued Real Security Sets You Free. ™ Remove the Cylinder Plug A B A Insert key and turn C B CAUTION: To avoid top pins clockwise to two o’clock position. Place flat end of follower against back of cylinder plug. springing out of cylinder shell, push follower all the way through in one careful, continuous motion. When completed, shell should be near center of follower. C Dump bottom pins from plug and remove old key. Discard old pins and keys.
B 00 & BA 00-Series – continued Real Security Sets You Free. ™ Reinsert Plug A B A With plug turned slightly, place back of plug against flat end of follower and push follower out smoothly by pushing plug into shell. 4 B Place thumb against plug face and carefully pull out key. NOTE: Do NoT PULL KEy oUT UNLESS SECURELy hoLDING PLUG FACE WITh yoUR ThUMB. ThIS KEEPS PLUG IN PLACE.
B 00 & BA 00-Series – continued Real Security Sets You Free. ™ Cylinder Cap Reassembly A B A Place cylinder assembly on smooth surface. Insert cap pin spring, then cap pin into small hole in back of plug. C B Place tailpiece with washer on top of plug. Be sure opening in washer straddles cap pin. C Position cylinder cap and screw into place with cylinder cap tool, but not tight. Cap pin should pop into one of the scallops in cap. test key by turning left and right, and removing it.
B 00 & BA 00-Series – continued Real Security Sets You Free. ™ Reassemble Crank Assembly REt RE tAin inER ER CRAn CRA nK tAiLP LPiiECE A B A Place crank into B Push retainer and crank retainer and slide onto tailpiece. combination, onto tailpiece, until it stops against cylinder cap. C C Replace adapter ring with the words facing you. (Leave this off if installing lock into 1½˝ diameter hole.) to rekey inside cylinder of B deadbolts, simply repeat steps through .
® Real Security Sets You Free.
S Light Duty Series – continued ® Real Security Sets You Free. ™ S Light Duty Commercial Levers A B A Insert key and turn it clockwise 90° to three o’clock position. C B Using tab on key C Remove key and remove gauge, depress retainer and remove knob or lever. cylinder. For S-Series locksets, notice sleeve around cylinder and remove sleeve. NoTE: ThIS SLEEvE IS MERELy A SPACER AND DoES NoT AFFECT ThE REKEyING PRoCESS. To REKEy — FoLLoW INSTRUCTIoNS 3A – 6B STARTING oN PAGE 18.
Real Security Sets You Free.
B100, BC100 & BR 00-Series – continued Real Security Sets You Free. ™ 1 Preparation 1A 1A B100/BC100 BR 00 A Remove cylinder assembly from A Remove the attached tailpiece from its collar. Place cylinder face down on a smooth surface. the back of the cylinder and place the housing face down on a smooth surface. Remove the Cylinder Cap ThE PhoToGRAPhS IN ThIS SECTIoN DEPICT B100 hoUSINGS; hoWEvER, ThE BC100 AND BR200 SERIES CyLINDERS REKEy ThE SAME WAy.
Real Security Sets You Free. ™ Remove the Cylinder Plug A B A Insert key and turn clockwise IMPoRTANT! MAKE SURE FoLLoWER NoTCh IS IN hoRIzoNTAL (NINE AND ThREE o’CLoCK) PoSITIoN. 4 Remove Bottom Pins 4A B holding follower firmly against to two o’clock position. Place flat end with square notch of follower against back of plug. B100, BC100 & BR 00-Series – continued back of plug, carefully push follower through cylinder shell. Support front of plug so it does not fall as it is pushed out.
B100, BC100 & BR 00-Series – continued Real Security Sets You Free. ™ Reinserting Cylinder Plug A B A Again, place flat end of B Insert key and place thumb follower against back of plug. Carefully push plug into shell, pushing follower out. against plug face. CAREFULLy pull key out, leaving plug locked in shell. Cylinder Cap Reassembly A B A Place cylinder face down on a smooth surface. Insert cap pin spring and cap pin into small hole in back of plug.
® Real Security Sets You Free.
B 00-Series – continued ® Real Security Sets You Free. ™ Remove Plug Retainer 1 Preparation 1A 1B A Remove cylinder assembly from rear of collar assembly. A B Remove phillips head screw and remove cylinder from its housing. A To remove “C-Shaped” retainer, align tailpiece with half-round notch in key gauge (40-104) as shown. Push key gauge against C-clip until it pops off. Remove tailpiece. Remove the Cylinder Plug A B A Insert key and turn clockwise to two o’clock position.
® B 00-Series – continued Real Security Sets You Free. ™ 4 Remove Bottom Pins Load new Bottom Pins ShEAR LinE A 4A A Dump bottom pins B A Use numbers on key bow or from plug and remove old key. Discard old pins and keys. use key gauge (see page 38) to determine new key combination. Insert new key all the way until it stops against plug face. Reinserting Cylinder Plug A B Load new bottom pins into plug with pins from keying kit to correspond with new key combination.
B 00-Series – continued ® Real Security Sets You Free. ™ Cylinder Cap Reassembly A B A Reinstall C-shaped plug retainer and tailpiece. Remove key. Be sure retainer does not block key slot on bottom of plug. C B Place cylinder into its housing. C Secure cylinder in place with Phillips screw.
Real Security Sets You Free.
Determining Combinations – continued Real Security Sets You Free. ™ Using the Key Gauge to Determine Combinations 1 With key cuts facing up, slide key into opening of key gauge near number “0” and slide to first cut (notch) from key bow. Slide key left until it stops on a number. Write down number and proceed to next cut. 4 Repeat until all cuts have a corresponding number, from bow to tip of key. This five or six-digit number is the key combination or “bitting”.
® Real Security Sets You Free. ™ Glossary ANSI American National Standards Institute. backset The distance from the edge of door to the center line of prep. bottom pin A bullet-shaped tumbler that comes in a variety of lengths that correspond to the depths of the key cuts. chassis The body of the lock itself, without any trim. cylinder The portion of a lock comprised of the plug, shell, pins (tumblers) and springs.
Administrative Offices 111 Congressional Blvd, Suite 200 Carmel, IN 46032 (800) 847-1864 Customer Service 14505 West 100th Street Lenexa, KS 66215 Order Processing (800) 847-1864 Schlage Distribution Service Center P.O.