Installation User guide

ManualsBrandsSchlage ManualsFor HomeFE575

Change faceplate, if necessary.

Choose the drawing that matches your door edge. If the hole has no mortise, change to the circular faceplate.

Door Edge Door Edge

No change necessary.

Check door dimensions.

See consumer.schlage.com/Service-Support for door

preparation instructions if dimensions are different.

2³⁄₄” (70 mm)

2³⁄₈” (60 mm)

2¹⁄₈” (53 mm)

Hole

1” (25 mm)

Door Edge

23780026

Keypad Lock

Installation Instructions

Model FE575

Additional Parts

9V Battery

Optional Latch

Faceplate

Pin Wrench

Tools Needed

• Phillips screwdriver

• Tape Measure

• Pencil

Optional

• Flathead Screwdriver

• Wood Block

• Hammer

• DO NOT use a power drill for installation!

• Use a screwdriver to remove product from packaging.

• Install and test lock with door open to avoid being locked out.

IMPORTANT NOTES

Prepare for Installation

Keypad

Latch

Latch/Strike

Screws (4)

Strike

Inside Lever

Lever

Screws (2)

Key

Summary of content (8 pages)

PAGE 1
Keypad Lock Installation Instructions Model FE575 23780026 Tools Needed • Phillips screwdriver • Tape Measure • Pencil Optional • Flathead Screwdriver • Wood Block • Hammer Inside Lever Keypad Lever Screws (2) Additional Parts Pin Wrench Optional Latch Faceplate Latch/Strike Screws (4) Latch Strike 9V Battery Key Prepare for Installation IMPORTANT NOTES • DO NOT use a power drill for installation! • Use a screwdriver to remove product from packaging.
PAGE 2
Install Lock 1 2 Install latch. Install strike onto door jamb. Make sure latch angle faces door jamb. Jamb Angle Angle Actual Size OR Wood Block (Not Included) Actual Size 3 Install battery. 4 Install keypad. Bar should slide smoothly through hole in latch. If not, check door dimensions.
PAGE 3
5 Install inside lever. Actual Size 6 If needed, switch levers. Correct If your lever looks like this, then no change is necessary. If your lever does not look like this, switch the levers by following the steps below. OR Incorrect a Insert the pin wrench into the hole in the lever. Push in and hold. b Pull the lever off. c d Repeat steps a and b to remove the Push each lever back lever from the other side of the door. into place. Switch the levers.
PAGE 4
Test Lock a Unlock. Did latch retract and then extend? 1. Find User Code A on the Keypad Locks Programming Guide. 2. Enter User Code A (four numbers) into the keypad. 3. Rotate and then release lever. Yes. Lock is installed correctly. No. Latch retracted but did not extend (latch bound). Check step 4. No. Nothing happened. Check step 3. Program Lock See the Keypad Locks Programming Guide that came with this lock. See the Keypad Locks User Guide for additional information. Go to keypad.schlage.
PAGE 5
Cerradura con teclado Verrou à clavier numérique Instrucciones de Instalación Modelo FE575 Instructions d'installation Modèle FE575 Herramientas necesarias • Desatornillador Phillips • Cinta métrica • Lápiz Outils nécessaires • Tournevis cruciforme • Ruban à mesurer • Crayon Opcional • Destornillador de cabeza plana • Bloque de Madera • Martillo Palanca interna Levier intérieur Teclado Clavier En option • Tournevis à tête plate • Bloc en bois • Marteau Tornillos de la palanca (2) Vis du levier (2)
PAGE 6
Instale la traba 1 Installez la serrure 2 Instalar el pestillo. Installez le verrou. Asegúrese de que el ángulo del pestillo mire hacia la jamba de la puerta. Assurez-vous que l'angle du loquet fait face au montant de la porte. Jamba Montant Ángulo Angle Instale el cerrojo en la jamba de la puerta. Installez la gâche sur le montant de la porte. Ángulo Angle Tamaño real Taille réelle O OU Tamaño real Taille réelle 3 Instale la batería.
PAGE 7
5 Instalar la palanca interna. Installez le levier intérieur. Tamaño real Taille réelle 6 Si es necesario, intercambie las palancas. Correcto Correct Au besoin, échangez les leviers. Si su palanca se ve como esta, no es necesario realizar ningún cambio. Si su palanca no se ve como esta, intercambie las palancas siguiendo los pasos que se indican a continuación. Si votre levier ressemble à cette illustration, il n'y a pas lieu de changer quoi que ce soit.
PAGE 8
Probar la cerradura a Essayez le verrou Desbloquee. Déverrouillez. 1. Encuentre el código de usuario A en la Guía de programación de cerraduras con teclado. 1. Repérez le code d'utilisateur A au guide de programmation des verrous à clavier numérique. 2. Ingrese el código de usuario A (cuatro dígitos) en el teclado. 2. Inscrivez le code d'utilisateur A (quatre chiffres) sur le clavier numérique. 3. Gire y luego suelte la palanca. 3. Faites pivoter et relâchez le levier.