Installation

ManualsBrandsSchlage ManualsFurnitureFE595

Change faceplate, if necessary.

Choose the drawing that matches your door edge. If the hole has no mortise, change to the circular faceplate.

Door Edge Door Edge

No change necessary.

Check door dimensions.

See consumer.schlage.com/Service-Support for door

preparation instructions if dimensions are different.

2³⁄₄” (70 mm)

2³⁄₈” (60 mm)

2¹⁄₈” (53 mm)

Hole

1” (25 mm)

Door Edge

23780018

Keypad Lock

Installation Instructions

Model FE595

Additional Parts

9V Battery

Optional Latch

Faceplate

Pin Wrench

Tools Needed

• Phillips screwdriver

• Tape Measure

• Pencil

Optional

• Flathead Screwdriver

• Wood Block

• Hammer

• DO NOT use a power drill for installation!

• Use a screwdriver to remove product from packaging.

• Install and test lock with door open to avoid being locked out.

IMPORTANT NOTES

Prepare for Installation

Keypad

Latch

Baseplate

Inside Lever

Cover

Screws (2)

Latch/Strike

Screws (4)

Strike

Key

Summary of content (8 pages)

PAGE 1
Keypad Lock Installation Instructions Model FE595 23780018 Tools Needed • Phillips screwdriver • Tape Measure • Pencil Optional • Flathead Screwdriver • Wood Block • Hammer Inside Lever Baseplate Additional Parts Keypad Cover Screws (2) Pin Wrench Optional Latch Faceplate Cover Latch 9V Battery Key Strike Latch/Strike Screws (4) Prepare for Installation IMPORTANT NOTES • DO NOT use a power drill for installation! • Use a screwdriver to remove product from packaging.
PAGE 2
Install Lock 1 2 Install latch. Install strike onto door jamb. Make sure latch angle faces door jamb. Jamb Angle Angle Actual Size OR Wood Block (Not Included) Actual Size 3 4 Prepare keypad. Install keypad. Remove sticker from hands-free post. IMPORTANT Wire must slide under latch. Bar should slide smoothly through hole in latch. If not, check door dimensions. Hands-free Post 5 6 Adjust hands-free post.
PAGE 3
7 8 Connect wire and battery. Place battery in holder and tuck wires. Lock will beep when battery is connected. Route wires behind curved piece and tuck, using tabs, so they will not be pinched by the cover. Tabs Curved Piece 9 Install cover. Actual Size 10 If needed, switch levers. Correct If your lever looks like this, then no change is necessary. If your lever does not look like this, switch the levers by following the steps below.
PAGE 4
Test Lock a Unlock. Did latch retract and then extend? 1. Find User Code A on the Keypad Locks Programming Guide. 2. Enter User Code A (four digits) into the keypad. 3. Rotate and then release lever. Yes. Lock is installed correctly. No. Latch retracted but did not extend (latch bound). Check step 4. No. Nothing happened. Check steps 7 and 8. Program Lock See the Keypad Locks Programming Guide that came with this lock. See the Keypad Locks User Guide for additional information. Go to keypad.schlage.
PAGE 5
Cerradura con teclado Verrou à clavier numérique Instrucciones de Instalación Modelo FE595 Instructions d'installation Modèle FE595 Herramientas necesarias Outils nécessaires • Desatornillador Phillips • Cinta métrica • Lápiz • Tournevis cruciforme • Ruban à mesurer • Crayon Opcional • Destornillador de cabeza plana • Bloque de Madera • Martillo En option • Tournevis à tête plate • Bloc en bois • Marteau Palanca interna Levier intérieur Placa base Plaque de base Teclado Clavier Tornillos de la cub
PAGE 6
Instale la traba 1 Installez la serrure 2 Instalar el pestillo. Installez le verrou. Asegúrese de que el ángulo del pestillo mire hacia la jamba de la puerta. Assurez-vous que l'angle du loquet fait face au montant de la porte. Jamba Montant Ángulo Angle Instale el cerrojo en la jamba de la puerta. Installez la gâche sur le montant de la porte.
PAGE 7
Conecte el cable y la batería. 8 Branchez le fil et la pile. La cerradura emitirá un pitido cuando se conecte la batería. La serrure émettra un bip lorsque la pile est branchée. Ubique la batería en el soporte y coloque los cables. Placez la pile dans support et insérez les fils. Pase los cables por detrás de la pieza curva y colóquelos, utilizando lengüetas, de manera que no los pellizque la cubierta.
PAGE 8
Probar la cerradura a Essayez le verrou Desbloquee. Déverrouillez. 1. Encuentre el código de usuario A en la Guía de programación de cerraduras con teclado. 1. Repérez le code d'utilisateur A au guide de programmation des verrous à clavier numérique. 2. Ingrese el código de usuario A (cuatro dígitos) en el teclado. 2. Inscrivez le code d'utilisateur A (quatre chiffres) sur le clavier numérique. 3. Gire y luego suelte la palanca. 3. Faites pivoter et relâchez le levier.