*P516-958* NDE Wireless Lock P516-958 Model NDE80 Installation Instructions and User Guide Cylinder Options Outside Assembly Pin wrench Full Size IC (FSIC) Ribbon Cable Key Small Format (SFIC) Spring Cage* Outside Lever* Cylinder* Standard Cylinder Inside Assembly Strike Escutcheon Screws Chassis Latch* Battery Cover Backplate Strike Options Inside Lever* Mounting Screws* Battery Strap Battery Holder ANSI Strike Battery Cover Screw T-Strike * Components shared with ND-Series lock.
B Door Thickness Adjustment Install strike and magnet tray assembly. Note: If dustbox is included, install first. CAUTION Magnet or magnet tray and included strike must be installed! DO NOT DISCARD! LL For 1C\v” thick doors, NO ADJUSTMENT IS REQUIRED. Continue to step 1. For 1B\,” or 2” thick doors, complete the following door thickness adjustment steps. A Remove chassis from outside assembly.
D Reinstall adjustment plate. Tighten until door thickness insert enters notch in adjustment plate. 1b To change handing, pull lever post until it stops, then rotate 180 degrees. Align lever catch pin and slide hole to latch side. Release lever post. Assembly will click into place. CAUTION Do not route ribbon cable before rotating chassis! 2 1 Lever Catch Pin 3 E 1 Secure chassis in outside assembly. Continue to next step.
2 Align assembly and install on door. Let the wire hang on the other side, through the hole. WARNING 4 Install spring cage. Align lever catch pin to door edge. Make sure the outside escutcheon is square before tightening the bolts. Do not pinch ribbon cable! WARNING Ensure that the lever catch pin is aligned with latch side before continuing! Lever Catch Pin Actual Size 5 Install inside escutcheon. 5a Connect the cable from the outside escutcheon to the connector on the inside escutcheon.
Cylinder and Lever Installation Lever With Interchangeable Core Cylinder Install cylinder tailpiece. Lever Removal Rotate cam in lever post until the cam stops. To remove a lever with a cylinder, insert key first, and turn it 90 degrees toward door edge. Press pin wrench into hole in lever, and pull off. To remove a lever without a cylinder, press pin wrench into hole in lever, and pull off. Insert key into cylinder and insert into lever. Rotate the key clockwise 15 degrees.
Install Batteries 6 7 Install battery cover screw. Choose either standard Phillips screw or Torx screw. Install batteries into battery holder. 6a Push the tab on the right of the battery securing strap, and pull out to release battery holder. 6b Install four high-quality alkaline batteries into battery holder. Follow markings for polarity. Install only new (4) AA alkaline batteries. 6c Connect cable from battery holder to connector on circuit board. OR 8 Screw into center of hole.
User Guide NEED HELP? See Troubleshooting on page 10. Lock Testing Power On Self Test The Power On Self-Test (POST) is a self-diagnostic test that the lock runs to verify that the lock is installed correctly. The POST takes approximately 30 seconds. During the POST, a series of audible beeps and LED flashes will occur. If the POST detects an issue, the test will conclude with three red flashes of the outside LED.
3. Select the “+” icon in the upper right corner. 4. Follow the lock commissioning wizard to complete initial setup of the lock. Locks can be commissioned as new, from a previously created profile, or cloned from an existing lock in your site. Upon selecting from these options (described below), the LED on the outside of the lock will begin blinking red to indicate connectivity with the app. • Select “Create New” to commission the lock with new configuration and access rights.
Safe Mode View lock audit information Audit information for each lock can be viewed from anywhere with the ENGAGE mobile app. Audit information is stored and viewed from the ENGAGE cloud database. If the lock has been configured to connect to the Wi-Fi network, audit information will be uploaded to the ENGAGE cloud database daily. If the lock has not been configured to connect to a Wi-Fi network, you must first connect to the lock with the ENGAGE mobile app and select “Update Door File” or “Get Audits.” 1.
Troubleshooting Problem Possible Cause Action No beeps or blinks when battery pack is connected. • Improper plug connection. • Pinched wires or bent pins. • Reversed battery or dead battery. • Check all wiring, and the three plugs. • Check that battery voltage is 6 VDC or better with new batteries. Fails power up self test. There were no three green LED blinks and beeps at the end of power up, just three RED LED blinks and beeps. • Motor not connected. • Battery voltage low.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
