Use and Care Manual

4
FLOOR PROFILES
4
Aluminum, Brass
3/32" - 3/16" (2 - 4.5 mm)
R = Radius
This product is
available in radius
Stainless steel
3/32" - 2 mm
= H
17/32" - 1-3/16" (14 - 30 mm)
1/8" - 3 mm
Single spacer design
= H
1/8" - 3 mm
Multiple spacer design
= H
1/4" - 1/2" (6 - 12.5 mm)
= H
1.1 Schluter
®
-SCHIENE
H =
mm - in.
Item No.
Stainless
steel 316L
(1.4404 = V4A)
(E/V4A)
Stainless
steel 304
(1.4301 = V2A)
(E)
Brushed
stainless
steel 304
(1.4301 = V2A)
(EB)
Solid
brass
(M)
Aluminum
(A)
Satin
anodized
aluminum
(AE)
2 - 3/32
-
E 20 - - A 20 AE 20
3 - 1/8 - E 30 - M 30 A 30 AE 30
4.5 - 3/16 E 45/V4A E 45 - M 45 A 45 AE 45
6 - 1/4 E 60/V4A E 60 E 60 EB M 60 A 60 AE 60
7 - 9/32 - E 70 - - A 70 AE 70
8 - 5/16 E 80/V4A E 80 E 80 EB M 80 A 80 AE 80
9 - 11/32 - E 90 - M 90 A 90 AE 90
10 - 3/8 E 100/V4A E 100 E 100 EB M 100 A 100 AE 100
11 - 7/16 - E 110 E 110 EB M 110 A 110 AE 110
12.5 - 1/2 E 125/V4A E 125 E 125 EB M 125 A 125 AE 125
14 - 17/32 - E 140 - - A 140 AE 140
15 - 9/16 E 150/V4A E 150 - M 150 A 150 AE 150
16 - 5/8 - E 160 - M 160 A 160 AE 160
17.5 - 11/16 E 175/V4A E 175 - M 175 A 175 AE 175
20 - 3/4 E 200/V4A E 200 - M 200 A 200 AE 200
21 - 13/16 - - - - A 210 AE 210
22.5 - 7/8 E 225/V4A E 225 - M 225 A 225 AE 225
25 - 1 E 250/V4A E 250 - M 250 A 250 AE 250
27.5 - 1-1/16 - - - - A 275 AE 275
30 - 1-3/16 E 300/V4A E 300 - M 300 A 300 AE 300
Length supplied: 8' 2-1/2" — 2.5 m
floor covering, but rather up to approx.
1/32" (1 mm) lower.
4. Fill the joint completely with grout or
setting material.
5. Work with materials and tools that will not
scratch or damage sensitive surfaces.
Setting materials must be removed
immediately.
RENO-T
1. Select the profile according to joint width,
to ensure proper support of the lateral
crosspiece.
2. The joint cavity must be at least 3/8"
(9 mm) deep and free of debris.
Substances that inhibit adhesion must be
removed from the sides of the joint.
3. Fill the joint with elastomeric sealant such
as Schluter
®
-KERDI-FIX or similar. Then
insert the vertical leg of RENO-T in the
joint so that the lateral crosspiece rests
completely on the edges of the surface
coverings.
4. Remove any excess sealant with a suitable
cleaner.
Maintenance
Schluter
®
edge-protection and transition
profiles require no special maintenance or
care and are resistant to mold and fungi.
Clean profiles periodically using pH neutral
cleaning agents.
Stainless steel surfaces exposed to the
environment or aggressive substances
should be cleaned periodically using a
pH neutral cleaner. Regular cleaning
maintains the neat appearance of stainless
steel and reduces the risk of corrosion.
All cleaning agents must be free of
hydrochloric acid, hydrofluoric acid, and
chlorides. Stainless steel surfaces develop a
sheen when treated with a chrome-polishing
agent.
Oxidation films on exposed solid brass
or aluminum can be removed by using
a conventional polishing agent, but the film will
form again.
In the case of anodized aluminum, color-
coated aluminum, and chrome-plated solid
brass, do not use abrasive cleaning agents.
Product Item Numbers
1.1 Schluter
®
-SCHIENE
Length = 3.05 m - 10'
H =
mm - in.
Item No.
Stainless
steel 304
(1.4301 = V2A)
(E)
Satin
anodized
aluminum
(AE)
8 - 5/16 E 80/300 AE 80/300
10 - 3/8 E 100/300 AE 100/300
12.5 - 1/2 E 125/300 AE 125/300