Use and Care Manual

6
WALL AND COUNTERTOP PROFILES
Product Item Numbers
H = 1/4" - 1/2"
(6 - 12.5 mm)
1/8" - 3 mm
R = Radius
Notes:
• Radius available for JOLLY in
metal profiles only.
• JOLLY in polished aluminum
and chrome-plated brass
require a relatively large
bending radius.
Note: Additional finishes are available for this product.
The design configuration of JOLLY is identical to that of
SCHIENE (see Floor Profiles). However, their materials
and finishes do vary. SCHIENE, in all materials and
finishes, is suitable for floor applications, as well as wall
and countertop applications. JOLLY is suited primarily for
walls and countertops. However, JOLLY in AM, AMGB,
AK, AKGB, AT, ATGB, ABGB and ACGB is also suitable
for floors and may be used in such applications to increase
design options.
H = 1/8"- 3/16"
(3 - 4.5 mm)
2.3 Schluter
®
-JOLLY
H =
mm - in.
Item No.
Chrome-
plated
solid
brass
(MC)
Polished
chrome
anodized
aluminum
(ACG)
Brushed
chrome
anodized
aluminum
(ACGB)
Satin
nickel
anodized
aluminum
(AT)
Polished
nickel
anodized
aluminum
(ATG)
Brushed
nickel
anodized
aluminum
(ATGB)
6 - 1/4 MC 60 A 60 ACG A 60 ACGB A 60 AT A 60 ATG A 60 ATGB
8 - 5/16 MC 80 A 80 ACG A 80 ACGB A 80 AT A 80 ATG A 80 ATGB
10 - 3/8 MC 100 A 100 ACG A 100 ACGB A 100 AT A 100 ATG A 100 ATGB
12.5 - 1/2 MC 125 A 125 ACG A 125 ACGB A 125 AT A 125 ATG A 125 ATGB
H =
mm - in.
Item No.
Satin
copper
anodized
aluminum
(AK)
Polished
copper
anodized
aluminum
(AKG)
Brushed
copper
anodized
aluminum
(AKGB)
Brushed
antique bronze
anodized
aluminum
(ABGB)
Satin
brass
anodized
aluminum
(AM)
Polished
brass
anodized
aluminum
(AMG)
6 - 1/4 A 60 AK A 60 AKG A 60 AKGB A 60 ABGB A 60 AM A 60 AMG
8 - 5/16 A 80 AK A 80 AKG A 80 AKGB A 80 ABGB A 80 AM A 80 AMG
10 - 3/8 A 100 AK A 100 AKG A 100 AKGB A 100 ABGB A 100 AM A 100 AMG
12.5 - 1/2 A 125 AK A 125 AKG A 125 AKGB A 125 ABGB A 125 AM A 125 AMG
H =
mm - in.
Item No.
Brushed
brass
anodized
aluminum
(AMGB)
Bright
black
anodized
aluminum
(AGSG)
Brushed
graphite
anodized
aluminum
(AGRB)
4.5 - 3/16 - A 45 AGSG -
6 - 1/4 A 60 AMGB A 60 AGSG A 60 AGRB
8 - 5/16 A 80 AMGB A 80 AGSG A 80 AGRB
10 - 3/8 A 100 AMGB A 100 AGSG A 100 AGRB
12.5 - 1/2 A 125 AMGB A 125 AGSG A 125 AGRB
DESIGNLINE
1. DESIGNLINE may be used with tiles that are
1/4" (6 mm) thick or greater.
2. Set tiles up to the area where DESIGNLINE is
to be installed as a decorative strip. Apply a
sufficient amount of thin-set mortar to this area
and/or to the back of DESIGNLINE and press
the profile into the mortar until its surface is flush
with the tile.
3. Set the adjacent row of tiles.
4. Set the tile to the integrated joint spacer,
which ensures a uniform joint of 1/16" - 1/8"
(1.5 - 3 mm). With the stainless steel and solid
brass profiles, leave a space of approximately
1/16" - 1/8" (1.5 - 3 mm).
5. Fill joints completely with grout or setting
material.
REMA
1. Adhere an aluminum bracket to the back of
each perimeter tile with thin-set mortar so that
the magnet extends beyond the tile’s edge.
2. Set tiles, with magnets attached, as perimeter
limits, so that four magnets extend into the
access opening.
3. To form the access panel cover, connect the
corresponding number of panel cover tiles
by attaching a tile to their backs with thin-set
mortar.
4. Using KERDI-FIX, silicone, or a similar adhesive,
adhere the counterplates to the back of the
panel cover in alignment with the perimeter
magnets.
5. After the adhesive has cured, install the cover
and seal the surrounding joint with a color-
coordinated sealing compound. Note: If the
access opening is substantially larger than
12" x 12" (30 x 30 cm), it may be necessary to
install two additional magnets.
Maintenance
Schluter
®
wall and countertop profiles require no
special maintenance or care and are resistant to
mold and fungi. Clean profiles periodically using
neutral cleaning agents.
Stainless steel surfaces exposed to the
environment or aggressive substances should be
cleaned periodically using a mild household cleaner.
Regular cleaning maintains the neat appearance of
stainless steel and reduces the risk of corrosion.
All cleaning agents must be free of hydro-chloric,
hydrofluoric acid, and chlorides. Stainless steel
surfaces develop a sheen when treated with a
chrome-polishing agent.
Oxidation films on solid brass or aluminum may
be removed with a common polishing agent, but
will form again.
In the case of chrome-plated brass, anodized
aluminum, color-coated aluminum, and textured
color-coated aluminum do not use abrasive
cleaning agents.