Installation Guide

SHOWER ASSEMBLY — Schluter
®
-KERDI waterproofing membrane 7
Areas of Application
Interior showers.
Over wood or concrete subfloors. See the Base information under
Requirements (below) for details.
Areas requiring disabled access/curbless applications; see detail K-SHBF
on page 12.
Limitations
Certain glass tiles may not be compatible with bonded waterproof
membranes and/or may require special setting materials. Consult glass
tile manufacturer and Schluter
®
-Systems for more information.
Certain moisture sensitive stones, e.g., green marble, or resin-backed
tiles may not be appropriate for use in wet areas such as showers or may
require special setting materials. Consult stone supplier and
Schluter
®
-Systems for more information.
Do not use sawn lumber curbs on concrete subfloors subject to
moisture migration.
Requirements
Plywood, OSB, or concrete subfloor must be clean, even, and load bearing.
Solid backing – gypsum wallboard, cementitious backer unit,
fiber-cement underlayment, fiber-reinforced water-resistant gypsum
backerboard/underlayment, coated glass mat water-resistant gypsum
backerboard, Portland cement mortar bed, concrete, or masonry.
Base – KERDI-SHOWER-T/-TS/-TT/-LT/-LTS or Portland cement mortar
bed.
Curb – KERDI-BOARD-SC, KERDI-BOARD, concrete, masonry block, or
sawn lumber sheathed with solid backing (see above).
Bench – KERDI-BOARD-SB, KERDI-BOARD, concrete, masonry block,
or sawn lumber sheathed with solid backing (see above).
KERDI-DRAIN/-LINE shall be properly supported.
KERDI-DRAIN/-LINE shall be connected to the waste line; use ABS
cement for ABS drains, PVC cement for PVC drains, a no-hub coupling
for stainless steel drains with no-hub outlets, and thread sealing
compound or tape for stainless steel drains with threaded outlets.
KERDI waterproofing membrane shall be installed up to the height of the
showerhead at minimum.
In enclosed shower areas, install KERDI waterproofing membrane on all
surfaces, including the ceiling, door jambs and the door header.
It is the specifier's responsibility to treat and address all penetrations
through the KERDI membrane or KERDI-BOARD (e.g., showerhead,
mixing valve, etc.) in the installation. All penetrations must be treated with
KERDI-SEAL-PS/-MV seals, KERDI-FIX or suitable sealant.
When using the stainless steel KERDI-DRAIN bonding flange, use
KERDI-FIX to bond KERDI to the drain.
All horizontal surfaces (e.g., benches, curbs, window sills, shelves, etc.)
must be sloped toward the shower drain. This can be done by sloping
the substrate or the tile.
Substrate Preparation
Verify that subfloor panels and solid backing are properly fastened to
framing members.
Any leveling of the subfloor must be done prior to installing
KERDI-SHOWER-T/-TS/-TT/-LT/-LTS/-SR and KERDI-BOARD-SC/-SB.
Solid Backing Materials
Gypsum wallboard – ASTM C1396/C1396M
Cementitious backer unit – ANSI A118.9 or ASTM C1325
Fiber-cement underlayment – ASTM C1288
Fiber-reinforced water-resistant gypsum
backerboard/underlayment – ASTM C1278
Coated glass mat water-resistant gypsum backerboard – ASTM C1178
Portland cement mortar – ANSI A108.1B
Concrete
Masonry
Setting and Grouting Materials
Unmodified thin-set mortar – ANSI A118.1
Grout – ANSI A118.3, A118.6, A118.7
Installation Specifications
Solid backing panels – follow manufacturer’s instructions
Portland cement mortar bed – ANSI A108.1B
Tile – ANSI A108.5
Grout – ANSI A108.6, A108.10
Other Considerations
When KERDI-SHOWER-T/-TS/-TT/-LT/-LTS tray dimensions do not
match the dimensions of the shower compartment, the tray may be cut
or extended with dry pack mortar.
When KERDI and tile are installed on the ceiling, the solid backing and
fasteners must be able to support the load of the tile and setting and
grouting materials.
A water test is strongly recommended before setting tile to verify a
successful installation. Wait 24 hours minimum after the membrane
installation is complete to allow for final set of thin-set mortar and ensure
waterproof performance at seams and connections. Refer to local
plumbing codes for any specific requirements in your area.
Schluter
®
-Systems profiles may be used to finish and protect outside
corners and eliminate the use of sealant at inside corners; see page 40.
Schluter
®
-SHOWERPROFILE-S/-R profiles eliminate the need for cutting
wedges of tile by covering the exposed wall area where the floor slopes
to KERDI-LINE.
Schluter
®
-SHELF-E/-W/-N are alternatives to tiled shelves that can be
easily installed on walls and in corners and niches; see page 40
Where a waterproof floor adjacent to the shower is desired, DITRA or
DITRA-HEAT uncoupling membranes shall be installed. Floor/wall
connections shall be sealed with KERDI-BAND.
Showers – Ceramic or stone tile
K-SH-K-20
Schluter
®
-KERDI waterproofing membrane