Specification

WALL AND COUNTERTOP PROFILES
4
the RONDEC profile. The 1-9/16" (39 mm)
vertical leg of the profile hides the exposed
edge of the sub-assembly. The integrated
joint spacer establishes a defined joint cavity
between the tile and the profile. The profile is
available in anodized aluminum and Tuscan
color-coated aluminum with various surface
finishes to allow for decorative design and
interesting accents. Matching inside and
outside corners are available.
Wall Access Panel System
11.1 Schluter
®
-REMA is the ideal system
for creating concealed access panels in
tiled wall coverings. The REMA assembly
kit consists of four aluminum brackets
with molded casings containing magnets
that are clamped to lateral, movable guide
shoes, and four ferro-magnetic metal
counterplates. REMA’s installation is
independent of tile size and thickness and
enables exact matching of the access panel
to the overall joint design. Thus, panels that
access electrical or plumbing components
do not impair the visual appearance of the
tile covering.
Material Properties and
Areas of Application
Schluter
®
wall and countertop profiles are
resistant to most chemicals encountered
in tiled environments. In special cases,
the suitability of a proposed type of
material must be verified based on the
anticipated chemical, mechanical, and/or
other stresses. Exceptions and special
considerations are listed below.
Stainless steel profiles are roll-formed,
resulting in a slightly different contour
from those made of extruded brass or
aluminum. Stainless steel can sustain high
mechanical stresses and is particularly well
suited for applications requiring resistance
against chemicals and acids; for example
in the food industry, breweries, dairies,
commercial kitchens, and hospitals,
as well as in residential applications.
Typically, the profiles are formed using
stainless steel 304 (1.4301 = V2A). For more
severe chemical exposure, such as de-icing
salts and chemicals used in swimming
pools, we recommend the use of stainless
steel 316 L (1.4404 = V4A), which offers
even higher corrosion resistance than the
304. Even stainless steel cannot withstand
all chemical exposures, such as hydrochloric
acid and hydrofluoric acid or certain chlorine
and brine concentrations.
Solid brass sustains high levels of
mechanical stress; for example, as edge
protection for outside wall corners or edges
of surface coverings. Brass is resistant to
most chemicals used in tiled environments.
Solid brass that is exposed to air will oxidize,
resulting in a natural patina. If exposed to
moisture or aggressive substances, heavy
oxidation and spotting may occur.
Chrome-plated brass is especially suited
for wall corners and finishing applications.
It is ideal for matching chrome fixtures.
Surface areas must be protected against
abrasion or scratching.
Aluminum profiles must be tested to
verify their suitability if chemical stresses
are anticipated. Cementitious materials,
in conjunction with moisture, become
alkaline. Since aluminum is sensitive
to alkaline substances, exposure to the
alkali (depending on the concentration
and duration of exposure) may result in
corrosion (aluminum hydroxide formation).
Therefore, it is important to remove mortar
or grout residue from visible surfaces.
In addition, ensure that the profile is solidly
embedded in the setting material and that
all cavities are filled to prevent the collection
of alkaline water.
Anodized aluminum profiles feature
an anodized layer that retains a uniform
appearance during normal use. The surface,
however, is susceptible to scratching and
wear and may be damaged by grout or
setting material. Therefore, these materials
must be removed immediately. Otherwise,
the description regarding aluminum
applies.
Color-coated aluminum is pretreated
(chromated) aluminum that is color-coated
with a polyurethane powder coat. The
coating is color-stable, UV-resistant, and
suitable for exterior use. Protect the profile
against abrasion or scratching.
Tuscan color-coated aluminum is
aluminum that is color-coated with real
metal powders and dyes in an acrylic resin.
The surface coating features a silicone
slip additive to reduce the potential for
abrasion, but profiles should be protected
against scratching.
PVC profiles are made of pre-colored, rigid
PVC that resists bending or scratching.
The material is UV-resistant, though not
permanently color-stable, in exterior
applications. PVC profiles are not suited
for corners or transitions subjected to heavy
mechanical stresses (e.g., at step edges or
floor transitions).
Installation
JOLLY, QUADEC, RONDEC,
DECO-DE, DECO-SG, INDEC,
ECK-E, RONDEC-DB, RONDEC-
STEP, and RONDEC-CT
1. Select the profile according to tile
thickness. Note: RONDEC-DB can
be used with tiles 1/4" - 1/2" (6 -
12.5 mm).
2. Using a notched trowel, apply thin-set
mortar to the area where profile is to be
placed. If JOLLY, QUADEC, RONDEC,
RONDEC-DB, or DECO-DE is to be
used as edging for an outside wall
corner, finish tiling one wall first; then
trowel thin-set mortar over the corner
area of the second wall.
3. Press the perforated anchoring leg of
profile into the mortar and align.
4. Trowel additional thin-set mortar over
the perforated anchoring leg to ensure
full coverage and support of the tile
edges.
5. Solidly embed the tiles so that the tiled
surface is flush with the top of the
profile; the profile should not be higher
than the tiled surface, but rather up to
approx. 1/32" (1 mm) lower.
Note: RONDEC-DB is intended to be
higher than the tiled surface.
6. Set the tile to the integrated joint spacer,
which ensures a uniform joint of 1/16"
- 1/8" (1.5 - 3 mm). With the stainless
steel profiles, DECO-SG, INDEC, and
RONDEC-DB, leave a space of
approximately 1/16" - 1/8" (1.5 - 3 mm).
7. To set tile along the face of
RONDEC-CT, apply thin-set mortar to
the back of the tile using a margin
trowel. Press the back-buttered tiles
into the face of the profile, making
sure to force thin-set mortar fully
into the dovetailed grooves. The
tiled surface should be flush with
the outer edge of the profile; the
profile should not be higher than the
tiled surface, but rather up to
approx. 1/32" (1 mm) lower. Note: The
recessed face accepts tile widths up to
1-1/8" (29 mm).
8. Fill joints completely with grout or
setting material. Note: Remove the
protective foil from ECK-E immediately
after grouting.
9. Work with materials and tools that
will not scratch or damage sensitive
surfaces. Setting materials must
be removed immediately, especially
from aluminum.
Note: Matching corners are available for
QUADEC, RONDEC, INDEC, RONDEC-