Use and Care Manual

FLOOR PROFILES
4
Aluminum, Brass
3/32" - 3/16" (2 - 4.5 mm)
R = Radius
This product is
available in radius
Stainless steel
3/32" - 2 mm
= H
Note: Additional finishes are available for this product. The design configuration of Schluter
®
-SCHIENE is identical to
that of Schluter
®
-JOLLY (see Wall and Countertop Profiles). However, their materials and finishes do vary. SCHIENE,
in all materials and finishes, is suitable for floor applications, as well as wall and countertop applications. JOLLY is
suited primarily for walls and countertops. However, JOLLY in AM, AMGB, AK, AKGB, AT, ATGB, ABGB and ACGB
is also suitable for floors, and may be used in such applications to increase design options.
17/32" - 1-3/16" (14 - 30 mm)
1/8" - 3 mm
Single spacer design
= H
1/8" - 3 mm
Multiple spacer design
= H
1/4" - 1/2" (6 - 12.5 mm)
= H
1.1 Schluter
®
-SCHIENE
H =
mm - in.
Item No.
Stainless
steel 316L
(1.4404 = V4A)
(E/V4A)
Stainless
steel 304
(1.4301 = V2A)
(E)
Brushed
stainless
steel 304
(1.4301 = V2A)
(EB)
Solid
brass
(M)
Aluminum
(A)
Satin
anodized
aluminum
(AE)
2 - 3/32
-
E 20 - - A 20 AE 20
3 - 1/8 - E 30 - M 30 A 30 AE 30
4.5 - 3/16 E 45/V4A E 45 - M 45 A 45 AE 45
6 - 1/4 E 60/V4A E 60 E 60 EB M 60 A 60 AE 60
7 - 9/32 - E 70 - - A 70 AE 70
8 - 5/16 E 80/V4A E 80 E 80 EB M 80 A 80 AE 80
9 - 11/32 - E 90 - M 90 A 90 AE 90
10 - 3/8 E 100/V4A E 100 E 100 EB M 100 A 100 AE 100
11 - 7/16 - E 110 E 110 EB M 110 A 110 AE 110
12.5 - 1/2 E 125/V4A E 125 E 125 EB M 125 A 125 AE 125
14 - 17/32 - E 140 - - A 140 AE 140
15 - 9/16 E 150/V4A E 150 - M 150 A 150 AE 150
16 - 5/8 - E 160 - M 160 A 160 AE 160
17.5 - 11/16 E 175/V4A E 175 - M 175 A 175 AE 175
20 - 3/4 E 200/V4A E 200 - M 200 A 200 AE 200
21 - 13/16 - - - - A 210 AE 210
22.5 - 7/8 E 225/V4A E 225 - M 225 A 225 AE 225
25 - 1 E 250/V4A E 250 - M 250 A 250 AE 250
27.5 - 1-1/16 - - - - A 275 AE 275
30 - 1-3/16 E 300/V4A E 300 - M 300 A 300 AE 300
Length supplied: 8' 2-1/2" — 2.5 m
2. The joint cavity must be at least 3/8"
(9 mm) deep and free of debris.
Substances that inhibit adhesion must
be removed from the sides of the joint.
3. Fill the joint with elastomeric sealant
such as Schluter
®
-KERDI-FIX or similar.
Then insert the vertical leg of RENO-T
in the joint so that the lateral crosspiece
rests completely on the edges of the
surface coverings.
4. Remove any excess sealant with a
suitable cleaner.
Maintenance
Schluter edge-protection and transition
profiles require no special maintenance or
care and are resistant to mold and fungi.
Clean profiles using common household
cleaning agents.
Stainless steel surfaces exposed to the
environment or aggressive substances
should be cleaned periodically using a
mild household cleaner. Regular cleaning
maintains the neat appearance of stainless
steel and reduces the risk of corrosion.
All cleaning agents must be free of
hydrochloric acid, hydrofluoric acid, and
chlorides. Stainless steel surfaces develop a
sheen when treated with a chrome-polishing
agent.
Oxidation films on exposed solid brass
or aluminum can be removed by using
a conventional polishing agent, but will
form again.
In the case of anodized aluminum, color-
coated aluminum, and chrome-plated
solid brass, do not use abrasive cleaning
agents.
Product Item Numbers