WA L L AN D COUNT E R T OP PR O F I L E S INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE FINISHING AND EDGE PROTECTION =H 11,5 2.3 Schluter®-JOLLY 2.5 Schluter®-RONDEC-DB 16.2 Schluter®-DESIGNBASE-SL EV 90° 45° 2.10 Schluter®-QUADEC 2.13 Schluter®-DIADEC 2.1 Schluter®-RONDEC 2.17 Schluter®-FINEC 2.11 Schluter®-QUADEC-FS 2 135° 2.2 Schluter®-DESIGNLINE ° 135 =H 2.6 Schluter®-ECK-E 2.8 Schluter®-RONDEC-STEP =H 2.14 Schluter®-DECO-DE 1.9 Schluter®-DECO-SG 2.7 Schluter®-ECK-K 2.
WALL AN D C O U N T ER TOP PR OFILE S Application and Function Wall Profiles 2.3 Schluter®-JOLLY is a finishing and edgeprotection profile for the outside corners of tiled surfaces. It features a trapezoidperforated anchoring leg that is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that provides a decorative finish and protects adjacent tiles.
WALL AN D C O U N T ER TOP PR OFILE S in wall applications (e.g., wainscotings and bases) with coverings at least 1/4" (6 mm) thick. The profile is particularly suited for finishing edges in retrofit applications, such as tile installation over existing wall tiles. Note: The outside corner can be used with any size of the DIADEC profile. 2.12 Schluter®-INDEC is an anodized aluminum finishing and edge-protection profile for outside ED 90° corners of tiled surfaces.
WALL AN D C O U N T ER TOP PR OFILE S features a symmetrically rounded edge with 1/4" (6 mm) radius, which matches the RONDEC profile, while the vertical leg of the profile hides the exposed edge of the sub-assembly. In addition, the profile effectively protects tiles in the edge area from mechanical and impact stresses. The integrated joint spacer establishes a defined joint cavity between the tile and the profile. RONDEC-STEP is suitable for residential applications, e.g.
WALL AN D C O U N T ER TOP PR OFILE S 3. Press the perforated anchoring leg of profile into the mortar and align. 4. Trowel additional thin-set mortar over the perforated anchoring leg to ensure full coverage and support of the tile edges. 5. Solidly embed the tiles so that the tiled surface is flush with the top of the profile; the profile should not be higher than the tiled surface, but rather up to approx. 1/32" (1 mm) lower. 5a.
WALL AN D C O U N T ER TOP PR OFILE S DESIGNLINE 1. DESIGNLINE may be used with tiles that are 1/4" (6 mm) thick or greater. 2. Set tiles up to the area where DESIGNLINE is to be installed as a decorative strip. Apply a sufficient amount of thin-set mortar to this area and/or to the back of DESIGNLINE and press the profile into the mortar until its surface is flush with the tile. 3. Set the adjacent row of tiles. 4.
WALL AN D C O U N T ER TOP PR OFILE S 2.3 Schluter®-JOLLY *Color Codes Item No. H= mm - in. 3 4.5 6 8 10 11 12.
WALL AN D C O U N T ER TOP PR OFILE S Aluminum 2.10 Schluter®-QUADEC Item No. H= mm - in. Aluminum =H 4.5 6 8 10 12.
WALL AN D C O U N T ER TOP PR OFILE S Aluminum 2.10 Schluter®-QUADEC *Color Codes Item No. H= mm - in. 4.5 6 8 10 11 12.5 - 3/16 - 1/4 - 5/16 - 3/8 - 7/16 - 1/2 Color-coated aluminum (AC) BW W SP PG QG VG SB GS Bright white White Quartz grey Q 45 color* Q 60 color* Q 80 color* Q 100 color* Q 110 color* Q 125 color* Sand pebble Traffic grey Classic grey Black brown Black * To complete the item number, add the color code (e.g., Q 45 G). Accessories Item No.
WALL AN D C O U N T ER TOP PR OFILE S 2.12 Schluter®-INDEC Item No. Polished chrome anodized aluminum (ACG) Satin anodized aluminum H= mm - in. Aluminum (AE) ED 90°IN 8 - 5/16 10 - 3/8 11 - 7/16 12.5 - 1/2 80 AE IN 100 AE IN 110 AE IN 125 AE Accessories Item No. Outside corner 90° ED / IN profile item number* How to order corners: * To complete the item number for corners, add the corresponding profile item number (e.g., ED / IN 100 AE).
WALL AN D C O U N T ER TOP PR OFILE S Stainless Steel 2.1 Schluter®-RONDEC Item No. H= mm - in. Stainless steel =H 4.5 6 7 8 9 10 11 12.5 15 - 3/16 - 1/4 - 9/32 - 5/16 - 11/32 - 3/8 - 7/16 - 1/2 - 9/16 Stainless steel 316L (1.4404 = V4A) Stainless steel 304 (1.4301 = V2A) (E/V4A) (E) Brushed stainless steel 304 (1.
WALL AN D C O U N T ER TOP PR OFILE S Aluminum 2.1 Schluter®-RONDEC Item No. H= mm - in. Aluminum =H 6 8 10 12.
WALL AN D C O U N T ER TOP PR OFILE S Brass 2.1 Schluter®-RONDEC Item No. H= mm - in. Brass 6 8 10 12.5 (MC) =H 6 8 10 12.5 - 1/4 - 5/16 - 3/8 - 1/2 Polished chrome anodized aluminum (ACG) H= mm - in.
WALL AN D C O U N T ER TOP PR OFILE S 2.6 Schluter®-ECK-E 2.6 Schluter®-ECK-E Item No. W= mm - in. 37 37 mm - 1-15/32" mm - 1-1 (E) 5/3 2" r = 8 mm 5/16" Stainless steel 304 (1.4301 = V2A) Item No. Brushed stainless steel 304 (1.4301 = V2A) (EB) 90º Angle =H 135º 6 8 11 - 1/4 - 5/16 - 7/16 E37 V2A 60/150 E37 V2A 80/150 E37 V2A 110/150 - 1/4 - 5/16 - 7/16 (E) Length supplied: 8' 2-1/2" — 2.50 m E37 V2A EB 60/150 E37 V2A EB 80/150 E37 V2A EB 110/150 Length supplied: 6' 7" — 2.
WALL AN D C O U N T ER TOP PR OFILE S 2.7 Schluter®-ECK-KHK Item No. Item No. W= mm - in. W = 9/16" - 15 mm Accessories Brushed stainless steel 304 (1.4301 = V2A) (EB) Stainless steel 304 (1.4301 = V2A) (E) Outside corner, 90º Length supplied: 4' 11" — 1.50 m 15 r = 11/32" 9 mm - 9/16 KHK15 E/150 Inside corner, 90º (2-way) Inside corner, 90º (3-way) KHK15 EB/150 Length supplied: 6' 7" — 2.00 m 15 - 9/16 KHK15 E/200 KHK15 EB/200 Length supplied: 8' 2-1/2" — 2.
WALL AN D C O U N T ER TOP PR OFILE S 2.11 Schluter®-QUADEC-FS Item No. H= mm - in. 2" - 50 mm =H 2-7/8" - 72 mm 8 (AE) Polished chrome anodized aluminum (ACG) Satin nickel anodized aluminum (AT) Brushed antique bronze anodized aluminum (ABGB) QF8/50 AE QF8/50 ACG QF8/50 AT QF8/50 ABGB Satin anodized aluminum - 5/16 Length supplied: 8' 2-1/2" — 2.50 m Accessories Item No.
WALL AN D C O U N T ER TOP PR OFILE S 2.9 Schluter®-RONDEC-CT Item No. H= mm - in.
WALL AN D C O U N T ER TOP PR OFILE S Schluter®-Systems Wall and Countertop Profiles 5-Year Limited Warranty COVERAGE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter-Systems* warrants that Schluter®-Systems Wall and Countertop Profiles (the “Products”)** will be free from manufacturing defects for a period of five (5) years from the date of purchase and only when the Products are used and installed in accordance with the terms and conditions of the Schluter®-System
This technical data sheet is subject to change without notice. Please visit www.schluter.com for the latest version. 12/2018 © 2018 Schluter Systems L.P. www.schluter.com 553099 Schluter Systems L.P. • 194 Pleasant Ridge Road, Plattsburgh, NY 12901-5841 • Tel.: 800-472-4588 • Fax: 800-477-9783 Schluter Systems (Canada) Inc. • 21100 chemin Ste-Marie, Ste-Anne-de-Bellevue, QC H9X 3Y8 • Tel.