Instructions

Please read the entire instructions for use carefully, as they contain
important information for safe operation. This product is freely
available. To achieve the best possible success, however, it must be
operated correctly and the safety regulations applied.
- Keep the instructions for use. Perhaps want to read it again later.
- Ask the seller or the manufacturer if you have more need
information or advice.
- At the end of the life of the UVC light source, it must be yours
security to be exchanged. The lamp is properly to dispose.
This leaflet includes
1. What is UVCARE® and what is it used for
2. What do you have to do before installing UVCARE®
note
3. How is UVCARE® to be installed
4. What are the risks of UVCARE®?
5. How long can UVCARE® be operated?
6. Are there any side effects when using the UVCARE®
7. More information
1. What is UVCARE® and what is it used for?
This product is used to decontaminate the room air, which
can be contaminated by viruses, bacteria or fungi,
including those enclosed in aerosols. It can reduce the
virus load in polluted rooms by up to 99.9%, whereby the
type of virus determines the application time. Flu viruses,
coronaviruses, viruses of almost all other infectious
diseases, fungal spores, etc. can be inactivated. It can be
assumed that mutations of known strains in your DNA will
also be attacked and will no longer be able to replicate
after exposure to radiation.
2. What do you have to consider before installing
UVCARE®?
UVCARE® may only be used indoors. Before drilling the
mounting screws, make sure that there are no power
cables. Connect the device by inserting the Euro plug into
a suitable socket.
The on / off switch for the device is also located on the
device plug.
Instructions for use
3. How is UVCARE® to be installed?
The most optimal installation is the suspension from the
ceiling, followed by the horizontal wall installation, the
vertical wall installation and the standing installation.
The ceiling suspension:
Screw the supplied support plates under the ceiling. Pay
attention to a tight fit! Screw in the retaining screw for the
wire rope. Insert the rope into the rope holder on one side
and then screw it into the center of the cross holder
(screw). Then thread the wire rope into the ceiling rope
post and align it. Repeat these steps for the second
bracket. The rope can be released again by pressing the
outer ring of the rope holder. Hang the UVCARE® just
above head height in order to achieve an optimal
disinfection result.
The wall suspension:
Fix the screws horizontally or vertically in the wall at the
appropriate distance from the cross bracket. Hang in the
UVCARE®. The horizontal installation at head height gives
a better result than the vertical installation. For reasons of
design or space, the UVCARE® can also be installed
vertically (perpendicular).
The stand installation:
The UVCARE® can also be installed as a portable stand
solution with the help of optionally available feet. In this
case you need an air intake plate with retaining screws
and corresponding feet (M8 external thread - at least
80mm).
4. What are the risks of UVCARE®?
UVCARE® has a light source inside that emits extremely
strong UV radiation. This radiation is encapsulated inside
and cannot penetrate through the lamellar openings
(intake - exhaust) to the outside. Since the UV rays can
damage the retina as well as cells of the skin, the product
must no longer be used, regardless of how damaged.
When replacing the lamp, make sure that the power
supply is only switched on after the UVCARE® has been
completely closed.
We recommend having the light source exchange carried
out by a specialist or in the production plant. This only has
to take place after an operating time of 9000 hours
(approx. One year of continuous operation). Do not use
the product after the maximum light source duration has
been exceeded.
Never insert objects of any kind into the intake or exhaust
fins as this can damage the fan. The device is self-cleaning
inside. Since there are no filter mats, there is no need to
change the filter material. If necessary, clean the outside
with a damp cloth and make sure that no liquid gets inside
the UVCARE®.
If these safety instructions are observed, operation, even
in 24h mode, is harmless.
The product is to be installed inaccessible to children.
In the event of any visible defects, the device must be shut
down immediately and returned to the manufacturing
plant for inspection.
5. How long can UVCARE® be operated?
There are no restrictions in operation. 24h operation is
permitted. Since an optimal disinfection result is only
achieved after the room air has been circulated approx. 4-
8 times, appropriate lead times should be taken into
account.
After a running time of min. 9000h the UVC lamp must be
exchanged to/for a similar one.
First, the UVCARE® must be completely disconnected from
the power supply and opened by unscrewing the locking
screw and the suction cover. The tube can be removed by
turning it through 90 ° (rotary plug socket) and the
replacement tube can be inserted in the same way. Then
secure the cover by twisting it and screw in the locking
screw. Only then reconnect the power supply.
The tube contains Hg and must be disposed of in
accordance with local regulations that also apply to
fluorescent tubes.
6. Are there any side effects when using the UVCARE®?
UVCARE® destroys the ability of microorganisms, viruses
and bacteria to multiply. This allows ozone to be released
in a purely physical process. However, the concentration is
always well below the European limit values. In the
circulating air, ozone automatically splits into oxygen and
hydrogen within a short time. It is possible that you will
notice the ozone-typical odor when there is a high level of
air pollution. However, this disappears after a short time.
Instructions for use
The noise level of the UVCARE® is very low at approx.
39dB. However, people can feel disturbed by the noise of
the fan in a completely quiet environment.
If you notice any side effects, please inform the
manufacturer specified in these instructions for use.
7. More information
UVCARE® disinfection lights adhere to an extremely strong
UVC lamp. Never look directly into the light source and
never expose the skin of humans or animals to the light
source unprotected, otherwise the cells can be severely
damaged.
UVCARE® is not a complete replacement for protective
masks and other hygiene measures, but complements
them accordingly.
UVCARE® is available in different UVC strengths, sizes and
power consumption. The exact version can be found on
the nameplate oft he UVCARE®.
UVCARE® must be disposed of in accordance with local
regulations.
Housing protection class
IP 20
electrical connection
220-240 V 50/60 Hz
Power
34 W/h
Electrical protection
5 A
Manufacturer / distributor / replacement items
Schmelter LED-Technology GmbH
Schmelter UVCARE®
Wiemecker Feld 14 * D-59909 Bestwig-Germany
Tel: [phone] Fax: [phone]
[e-mail] * www.uvcare.de
Information as of September 2020