Operation Manual Models JC95B, JC95W, JC132B, JC132W 1 |Page
TABLE OF CONTENTS 1 GENERAL INFORMATION Pages 1.1 Foreword 3 1.2 General use 3 1.2.1 Children 3 1.2.2 Warnings 3 1.2.3 Safety 4 1.3 Controller Settings 5 1.4 Responsibility of the customer 5 2 TECHNICAL DATA 2.1 Materials and Refrigerant 3 INSTALLATION 3.1 Positioning 6 3.1.1 Cooler levelling 6 3.2 Electrical connection 6 4 MAINTENANCE 7 5 TROUBLESHOOTING 7 6 WARRANTY 8 6.1 Warranty Statement 9 6.
1. GENERAL INFORMATION 1.1 FOREWORD The purpose of this document is to provide important information regarding the installation, use and maintenance of the cooler. Before any operation, you should read carefully the information contained in this manual. The manufacturer assumes no liability for parts or labour coverage for component failure or other damages resulting from improper usage, installation or failure to clean and / or maintain product as set forth in these instructions. 1.
Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Do not Store explosive substances such as aerosol cans with a flammable propellant in this appliance. Don’t store flammable liquids near unit that may omit vapour. Unplug unit when not in use and also when maintenance and cleaning is taking place.
1.
Explanation of the buttons Buttons Normal operation Press for short press Press for long press Toggle ECO mode Toggle defrost Light ON/OFF Power ON/OFF Increase set point / Decrease set point Toggle °C and °F How to set the temperature Set the desired cooling temperature by pressing the corresponding button or . Each depression of the buttons will raise or lower the temperature setting.
1.4 INSTALLATION OF THE HANDLE To install the handle, please follow these instructions • Carefully pull the door gasket (seal) away from the door in the area where the handle will be attached. • Place the handle over the screw holes on the outside of the door and attach it with the screws that have been provided. Tighten the screws. • Press the door gasket back into its groove. 1.5 REVERSING THE DOOR SWING This appliance has the capability of the door opening from either the left or right side.
1.6 RESPONSIBILITY OF THE CUSTOMER Ensure that the electrical outlet is connected effectively to earth (ground), suitable to provide the voltage indicated on the data plate. Make sure that the cooler is placed on a level surface. 2. TECHNICAL DATA 2.1 MATERIALS AND REFRIGERANTS Interior or exterior surfaces that come into contact with the product are made of steel, aluminium or non-toxic plastic materials. The refrigerant used is approved by government regulations.
3.2 ELECTRICAL CONNECTION Warning: Do not use extension cords The cooler works on single-phase voltage (220-240V/50Hz) power supply. To switch on the cooler, insert the plug into the outlet. Ensure that: . When the cooler is operating, check that the supply voltage is not dropping or increasing under/over +10% the rated voltage (195 Volts to 253 Volts) *Ensure the cooler is connected to correct voltage prior to plugging it in; there is a description to identify the correct voltage on rear of the cooler.
4. MAINTENANCE - Before cleaning the cooler always remember to unplug it. - Unplug the cooler at the electrical outlet; never pull the service cord. - Do not use sharp objects for cleaning. - Clean the inside cabinet of cooler with a clean damp cloth or with neutral soap. Avoid damage by never using abrasive or flammable cleaning products. - Clean the condenser every 6 – 12 months with a vacuum cleaner or a brush to eliminate the dust accumulation.
c) The appliance is excessively noisy. -Verify the equipment is level. -Ensure that the equipment is not touching other equipment that could cause vibration, like piping touching metal cover or other parts. -If fan is causing noise it may be faulty bearing For extra trouble shooting information please go to: http://kb.bar-fridges-australia.com.au/ 6.
| P a g e
| P a g e
