Manualshelf

Application Guide

ManualsBrandsSchneider Electric ManualsSmart HomeZ-Wave Switch
12
-01-
-02-
-03-
Step 7 Restore power at the circuit breaker and test the system.
♦ OPERATIONS
1. Local control
Notice:
- After a power failure, the switch returns to OFF state.
2. Group control the nodes of association group 2
Note: Please refer to association setting for nodes group 2 setup. This requires a gateway with advanced
features, and assumes the device has included in a network.
3. Inclusion to a Z-Wave network
Notice: The device supports up to S2-authenticated inclusion method, based on the gateway’s feature, it
is highly recommended to only select S2-authenticated or the highest inclusion method, and uncheck the
rest methods. This would ensure the highest security level during Z-Wave service. During S2-
authenticated inclusion, users may be asked to scan the QR code or entering 5-digit ping code attached
on the device.
➢ Smart Start Inclusion
The feature assumes the gateway has implemented Smart Start. Users could use the APP of the
gateway or the gateway camera to scan the QR code on device or on device package even
before powering on the device, when the device is powered on, it shall be automatically added to
the gateway.
This application guide applies to the following products.
SQR14101WHZ,SQR14101LAZ,SQR14101BKZ
Z-WAVE SWITCH SINGLE POLE
ENERGY MONITORING
FCC ID: 2AUCU-14101Z
IC: 25381-14101Z
CAN ICES-3(B)/NMB-3(B)
Add Z-wave plus logo
♦ INSTALLATION
Step 1 Turn off power at circuit breaker or fuse and test that power is off before wiring.
Step 2 Connect the device as shown in the wiring diagram.
♦ SPECIFICATIONS
• Z-Wave technology creates a mesh network for command and control interoperability with other Z-Wave
compliant controller and devices
• Manual and Remote ON/OFF control of any connected lighting and other electrical load
• Can be used for 3-Way (Multi-location) application together with Z-Wave auxiliary switch
SQR50101**Z
• Measure the energy usage of the connected loading, display the actual consumption (in W) and
the accumulated power used (in kWh) in the user interface of the gateway
Notice: for energy measurement feature, please refer to the gateway installation manual for
energy usage display.
Notice:
The device is meant for non-critical automation activities and is not intended to support life
safety or medical equipment being plugged into them over concerns about being
unintentionally turned off with an automation routine.
WARNING: CALIFORNIA PROPOSITION 65
This product can expose you to chemicals including Carbon black, which is known to the State of
California to cause cancer, and Bisphenol A (BPA), which is known to the State of California to
cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
WARNING
Be sure to read the instruction carefully before installation, and the manufacturer will not
be responsible for any product damage that does not follow the instruction
1. Wet hands are strictly prohibited.
2. Must work strictly according to the rated load.
3. Do not continue to work after self-disassembly of any nature and damage of external
forces.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• This equipment must only be installed and serviced by qualified electrical personnel.
• Turn off all power supplying this equipment before working on or inside equipment.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors, and covers before turning on power to this equipment.
• Use with Copper wire only
• Indoor use only.
Failure to follow these instructions will result in death or serious injury..
DANGER
DANGER
Step 3 Check connections to be sure they are tight and no bare conductors are exposed.
Step 4 Insert the device into the standard outlet box carefully. Make sure the device is
fixed to the outlet box using the supplied screws.
Step 6 Install the wall plate (not included) following below figure.

Summary of content (2 pages)