InsightFacility Owner's Guide 990-91411A February 2021 http://solar.schneider-electric.
Copyright © 2021 Schneider Electric. All rights reserved. © 1982-2013, QNX Software Systems Limited. All rights reserved. Microsoft, Windows, and Internet Explorer are owned by Microsoft. Chrome is owned by Google. Safari and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. All other trademarks are owned by Schneider Electric Industries SAS or its affiliated companies.
Safety Information Important Information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
Product Safety Information DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, ARC FLASH, AND FIRE n Read all instructions, cautionary markings, and all other appropriate sections of this guide before installing, operating, troubleshooting or performing maintenance on the InsightFacility. n Exercise extreme caution at all times to prevent accidents. n These instructions are for use by qualified installers only. Failure to follow these instructions will result in death or serious injury.
NOTICE EQUIPMENT DAMAGE n All cables connected to the InsightFacility must run indoors and not be susceptible to lightning strikes. n Turn OFF all devices before connecting cables. The InsightFacility does not have an ON/OFF switch. n Do not connect an Ethernet cable from the InsightFacility to the WAN/MODEM port on the network router. n Do not connect an Ethernet cable plug into a Xanbus port on the InsightFacility.
Audience This guide is intended for use by anyone who plans to install and operate the InsightFacility communications device as part of their power plant system. Installation instructions are meant for installers only. The installers have training, knowledge, and experience in: n Installing electrical equipment. n Applying all applicable installation codes. n Analyzing and reducing the hazards involved in performing electrical work. n Selecting and using Personal Protective Equipment (PPE).
About Purpose The purpose of this Owner's Guide is to provide explanations and procedures for installing, operating, configuring, maintaining, and troubleshooting the InsightFacility. Scope The Owner's Guide provides safety guidelines, planning, and setup information, procedures for installing the product, as well as information about troubleshooting the product. It does not include information on how to install, configure and use other Schneider Electric products.
InsightFacility Owner's Guide Related Products For more information about related products, refer to: n XW Pro Inverter/Charger Owner’s Guide (part number: depends on configuration - see http://solar.schneider-electric.com/) n Conext XW+ Inverter/Charger Owner’s Manual (part number: depends on configuration see http://solar.schneider-electric.
Contents Safety Information Audience About 2 5 6 Purpose 6 Scope 6 Firmware Revision 6 Abbreviations and Acronyms 6 Related Products 7 Related Information 7 Overview 12 Introduction 13 Compatible Xanbus™ Components 13 Material List 14 Physical Features 16 Power Button Operation 17 LED Indicator Operation 17 26-pin Connector Pinouts 18 Types of InsightFacility Networks 19 Power Sources for the InsightFacility 19 InsightFacility Web User Interface 20 Installation 22 Choos
Changing the Password 39 Changing InsightFacility Settings 41 Plant Setup 41 Changing the Time 42 Import and Export Settings 42 Units 43 Install Package 44 Restarting the InsightFacility 44 Upgrading Firmware 46 Installing InsightFacility Upgrades From a USB Drive 46 Installing InsightFacility Upgrades Remotely 46 Upgrading Other Device Firmware 47 Configuring Devices Connecting and Configuring Modbus Devices Modbus TCP Settings 50 51 52 Removing a Modbus Device 53 Changing Devic
Installing the InsightFacility Security Certificate Root Certificates 78 79
1 Overview What's in This Chapter? Introduction 13 Compatible Xanbus™ Components 13 Material List 14 Physical Features 16 Power Button Operation 17 LED Indicator Operation 17 26-pin Connector Pinouts 18 Types of InsightFacility Networks 19 Power Sources for the InsightFacility 19 InsightFacility Web User Interface 20
InsightFacility Owner's Guide Overview Introduction The InsightFacility is a multi-function communication device that provides an overall view of system performance for residential power monitoring systems. It also provides a communications gateway between a network of Xanbus™-enabled devices and Modbus devices. Operators can configure the InsightFacility system and monitor performance with third party software packages and building management systems.
Overview InsightFacility Owner's Guide n Conext Automatic Generator Start (AGS) n Conext System Control Panel (SCP) n Conext SW Inverter/Charger n Conext MPPT 60 150 Solar Charge Controller n Conext MPPT 80 600 Solar Charge Controller n Conext MPPT 100 600 Solar Charge Controller n Conext Battery Monitor For details on specific models supported, see Electrical Specifications on page 73.
InsightFacility Owner's Guide Overview 4 75 mm DIN rail 5 Ethernet cable (CAT5e) not shown • BMS CAN terminator • 26-pin connector (see Physical Features on page 16) not supplied 15 Power adapter: Manufacturer: CUI P/N: SMI18-12-V-P5 Description: AC-DC Power Supply, 12Vdc Output Voltage, 1.
Overview InsightFacility Owner's Guide Physical Features The following illustration shows the InsightFacility. The tables in the following sections contain descriptions of the connectors, indicators, and data ports on the InsightFacility.
InsightFacility Owner's Guide Overview Power Button Operation Table 1 Power button operation Press and hold Number of InsightFacility operation duration beeps 3 seconds 1 InsightFacility will restart 6 seconds 2 InsightFacility will shutdown 9 seconds 3 User settings will be reset and InsightFacility will restart 12 seconds 4 Factory default settings will be reset and InsightFacility will restart LED Indicator Operation Figure 3 Ports, buttons, and indicators Green Power The InsightFacil
Overview InsightFacility Owner's Guide 26-pin Connector Pinouts Figure 4 26-pin connector Bottom Row Top Row 2 9–24VDC power input 1 GND 4 GND 3* 0–10VDC analog input 1 5* 0–10VDC analog input 2 7 GND 9* 4–20mA input 1 6* 12VDC digital input 1 8* 12VDC digital input 2 10 ISO1 CAN GND 12 ISO1 CAN L 14 ISO1 CAN H 16 ISO2 RS485 GND 18 ISO2 RS485 1A 1 3 5 7 9 11 13 15 17 19 21 23 25 2 4 6 8 10 12 14 16 18 20 22 24 26 11* 4–20mA input 2 13 GND 15* Relay 1 NO 17* Relay 1 COM 20 ISO2 RS485 1B
InsightFacility Owner's Guide Overview Types of InsightFacility Networks The InsightFacility can interface with different LAN devices using wired or wireless connections, so you can configure your Xanbus devices and monitor your power system performance.
Overview InsightFacility Owner's Guide In the InsightFacility, the SELV circuits and their intended connections are: n The AC/DC power adapter connected to the power port of the InsightFacility. n Xanbus communications and power which come from SELV circuits on Xanbusenabled Schneider products. n 9–24 V DC power input connections which must be SELV and are connected to the InsightFacility via the 26-pin connector. n Ethernet circuits or Class 2 circuits (Class 2 is a 24V, 100VA limited circuit).
InsightFacility Owner's Guide Overview Figure 5 Web user interface 1 Main menu bar – displays major menu items including the Dashboard, Devices, Events, and Setup commands. It includes About, which shows InsightFacility device information. 2 Sub-menu tabs – displays sub-menu items expanding commands associated with the major menu items. 3 Main display area 4 Web app version and build number 5 Information bar – displays the system date, time, and user type.
2 Installation What's in This Chapter? Choosing a Location 23 Materials and Tools Required 24 Mounting the InsightFacility 25 DIN Rail Mount 25 Connecting the InsightFacility to the Xanbus Network 25 Connecting the InsightFacility to the Internet 27 Turning On the InsightFacility 29 Turning Off the InsightFacility 30 Power Cycling 30
InsightFacility Owner's Guide Installation Choosing a Location Figure 6 Location choices 50mm 50mm 50mm 50mm n Choose a clean, dry, easily accessible location indoors. n If you mount the InsightFacility on a wall, the recommended height is at eye-level so that you can clearly see the LED indicators and have easy access to the data and communication ports. n All of the ports on the InsightFacility are accessible from the sides of the device when mounted on a wall or DIN rail.
Installation InsightFacility Owner's Guide Materials and Tools Required The following materials are supplied in the InsightFacility package: n One InsightFacility unit n One InsightFacility Quickstart Guide n One CAT5e Ethernet cable (7-ft) n One 26-pin connector n One 75 mm DIN rail The following materials and tools are not supplied but are required to complete the installation: 990-91411A n One AC/DC power supply adapter n CAT5e Ethernet cable(s) n Modbus network cables(s) n Wire stri
InsightFacility Owner's Guide Installation Mounting the InsightFacility DIN Rail Mount To mount the InsightFacility on the DIN Rail: 1. Use a standard 35-mm “top hat” DIN rail (EN50022). 2. You may choose to move the mounting clip to the side as shown. 3. Attach the device to the DIN rail. Hook the bottom catch of the clip onto the rail, pull up a little to retract the bottom catch and hook the top catch of the clip onto the rail. 4. Connect the wiring and cables.
Installation InsightFacility Owner's Guide d. If you have two separate Xanbus networks connect the second network to Xanbus 2. e. Devices on the Xanbus 1 network will not communicate with devices on the Xanbus 2 network. f. See Figure 7 for Xanbus 1 pair of ports - one top and one bottom. NOTICE EQUIPMENT DAMAGE n Do not connect a Xanbus cable plug into the Ethernet port on the InsightFacility. n Connect only to Xanbus ports and use the network terminators to each end device in the daisy chain.
InsightFacility Owner's Guide Installation Connecting the InsightFacility to the Internet Before connecting a computer and router to the InsightFacility, make sure it meets the following prerequisites. n Microsoft® Windows® 7 or later n Mac OS® X 10.4.8. or later n Google Chrome™ 78.x or later n Microsoft® Windows® Internet Explorer® 11.476 or later n Safari® 5.x or later n JavaScript and cookies must be enabled in your web browser.
Installation InsightFacility Owner's Guide Figure 8 Ethernet connection (LAN) 2 1 MODEM LAN 990-91411A 1 Router/modem 2 Laptop 3 InsightFacility unit 4 Ethernet cables 4 3 28
InsightFacility Owner's Guide Installation Turning On the InsightFacility Before turning on the InsightFacility, you must connect it to a power source. Figure 9 Power connections and button Xanbus [B] AC/DC power adapter [A] 26-pin connector [C] NOTE: In the 26-pin connector, pin 1 connects to a 9-24VDC source and pin 2 connects to GND Power input. See " 26-pin connector" on page 18. To turn on the InsightFacility: 1. Select a power source to the InsightFacility.
Installation InsightFacility Owner's Guide 4. Observe the LED indicators and wait for the Power LED to light up (solid). The InsightFacility is now turned on. 5. Proceed to "Logging in to the InsightFacility Web Application" on page 37. Turning Off the InsightFacility To turn off the InsightFacility: n Press the Power button according to the settings in Table 1 on page 17 or use the web user interface to shut down the unit and turn it off.
3 Getting Started What's in This Chapter? Using the InsightFacility Web App via Wi-Fi Access Point (AP) 33 Enabling Wi-Fi Station 33 Web Security 35 Configuring the InsightFacility 36 Logging in to the InsightFacility Web Application 37 User Access Levels 38 Changing the Password 39 Changing InsightFacility Settings 41 Plant Setup 41 Changing the Time 42 Import and Export Settings 42 Units 43 Install Package 44 Restarting the InsightFacility 44 Upgrading Firmware 46 Installin
InsightFacility Owner's Guide Getting Started Using the InsightFacility Web App via Wi-Fi Access Point (AP) Wi-Fi Access Point allows you to connect your PC or tablet directly to the InsightFacility. This is typically only used for fist-time configuration. NOTE: This procedure is not about connecting to a local area network (LAN) via Wi-Fi (for more information, see Enabling Wi-Fi Station). In order to establish a user interface with InsightFacility, a direct Wi-Fi connection is necessary.
Getting Started InsightFacility Owner's Guide (see Using the InsightFacility Web App via Wi-Fi Access Point (AP)). NOTE: Wi-Fi Station cannot be used unless the LAN cable is disconnected. To enable Wi-Fi Station: 1. Go to Setup > Network > Network settings. 2. Select your network. If you do not see your network, go to step 4. 3. Enter the network password.
InsightFacility Owner's Guide Getting Started c. Enter the network password. d. Click Connect. Web Security When you access the InsightFacility web user interface you may see a warning stating that the web page is not trusted or the web page is not secure. This occurs because the InsightFacility security certificate is not installed on your computer’s operating system. You can elect to proceed anyway, if you are on a private local area network.
Getting Started InsightFacility Owner's Guide Configuring the InsightFacility To complete InsightFacility setup, you must successfully complete the procedures in Installation on page 22. Make sure the InsightFacility is connected, the Power LED is on, and the Event LED is off. Your Xanbus devices should still be in standby mode. When you initially log in to the web user interface, most of the setup information appears automatically with their default values.
InsightFacility Owner's Guide Getting Started Logging in to the InsightFacility Web Application 1. If you have connected the InsightFacility via Wi-Fi Access Point, go to the IP address https://192.168.100.1 to access the web user interface. 2. If you have connected the InsightFacility via Ethernet or Wi-Fi Station, use the following steps: a. Insert a blank USB drive into the InsightFacility USB port. Ensure there are no firmware upgrade files on this USB drive. b.
Getting Started InsightFacility Owner's Guide 7. Change the InsightFacility SSID and network password: a. Go to Setup > Network > Wifi Access Point Settings b. (Optional) Replace the current Wi-Fi network name under the SSID field with an appropriate name. You are limited to 64 alphanumeric characters including symbols. c. Replace the current password under the Password field with 10 or more alphanumeric characters including symbols. d. Click Apply to save the new password and/or SSID.
InsightFacility Owner's Guide Getting Started Changing the Password What to expect when logging in for the first time: n When logging in to the web application for the first time, either as Admin or User or Guest, the system will automatically ask you to change the password from the factory default Admin123 or User123 or Guest123, respectively. Important: To protect your privacy, change all default passwords when you login for the first time.
Getting Started InsightFacility Owner's Guide Figure 15 Password screen n You may have to log in again after changing the initial password. To change the password after the initial log in: Figure 16 Change password setting 1. Click Setup > Manage Passwords > Change Passwords. 2. Select the User name type. Note: Admin-level can change all passwords. User-level can change User and Guest passwords. Guest-level cannot change any passwords. l Admin l User l Guest 3. Enter the Old password. 4.
InsightFacility Owner's Guide Getting Started 5. Enter the Confirm password. 6. Click Apply. Your settings will be immediately applied. Changing InsightFacility Settings The procedures for configuring the other InsightFacility Settings are described in the following sections. To change InsightFacility settings: 1. In the main menu bar, click Setup > Configuration. The Configuration settings appear in the main display area. 2. Click any of the following settings.
Getting Started InsightFacility Owner's Guide 3. Enter the Installed AC capacity (kW). 4. Enter the Installed year. 5. Click Apply. Your settings will be immediately applied. Changing the Time In order for the Cloud interface to work properly, you must set the correct time and time zone. You can choose to use the network time for your system. Figure 18 Time setup screen To change the InsightFacility time: 1. Click Setup > Configuration > Time setup. 2. Select the Time zone.
InsightFacility Owner's Guide Getting Started 2. Click Import & export settings. a. Click Download. The compressed configuration file usersettings.zip will be automatically saved to the Downloads folder of the browser. b. If necessary, you may copy this file to an external drive and later import it to a different InsightFacility device. To import settings: 1. In the main menu bar, click Setup > Configuration. The Configuration settings appear in the main display area. 2. Click Import & export settings. a.
Getting Started InsightFacility Owner's Guide Install Package To install a InsightFacility upgrade remotely: 1. From the InsightFacility Web Application home page, go to Setup > Configuration > Install Package. 2. Download the firmware package. a. Click Get package. This will take you to the InsightFacility product webpage. b. From the product webpage, go to DOWNLOADS > Firmware. c. Search for the latest firmware package from the list and click it to begin downloading. d. Save the .
InsightFacility Owner's Guide Getting Started Figure 21 Restart InsightFacility screen Choose what to do in the web user interface: 1. Click Setup > Configuration > Restart InsightFacility. 2. Click any of the action buttons depending on the kind of reset you want to perform. l Restart InsightFacility – will execute a soft restart of the InsightFacility unit. l Reset configuration – will execute a reset of InsightFacility settings, including network configuration, and plant setup.
Getting Started InsightFacility Owner's Guide Upgrading Firmware You can perform firmware upgrades for your InsightFacility and Xanbus-enabled devices when they are available for download.
InsightFacility Owner's Guide Getting Started Upgrading Other Device Firmware It is possible to upgrade a device's firmware through the InsightFacility web application. NOTICE RISK OF EQUIPMENT DAMAGE n Consult the device’s Owner’s Guide when changing the device’s settings. n Make sure the device connected on the Xanbus or Modbus network is in Standby mode before changing settings. n Do not change any settings unless you are familiar with the device.
Getting Started InsightFacility Owner's Guide 3. Click Firmware . 4. Click Upgrade. 5. Follow the step-by-step upgrade instructions. 6. To upgrade all similar devices in the network, click Upgrade All. 7. Follow the step-by-step upgrade instructions. 8. Use the Operating Mode menu to put the device back into normal operating mode.
4 Configuring Devices What's in This Chapter? Connecting and Configuring Modbus Devices Modbus TCP Settings 51 52 Removing a Modbus Device 53 Changing Device Settings 54 Device Association 56 Cloud Settings 57 Configuring an AC-Coupled System 58 Configuring the Grid Code Region 58 Enabling California Rule 21 60
InsightFacility Owner's Guide Configuring Devices Connecting and Configuring Modbus Devices NOTE: For Modbus map information, contact Schneider Electric. Connect Modbus wires to pins 16, 18, and 20 (see Physical Features), and then complete the following steps in the InsightFacility web application: 1. Go to Setup > Configuration > Modbus Settings. 2. Complete the Serial Port setup and then click Apply. 3. Go to Home > Setup > Device Detection. 4.
Configuring Devices InsightFacility Owner's Guide Modbus TCP Settings Modbus TCP allows an external controller to communicate with the InsightFacility and perform monitoring and control activities. Important: The Modbus TCP protocol is not secure. DO NOT route this protocol over an untrusted public or private network. Ensure adequate cybersecurity protections are enforced on your network. Maintain appropriate firewalls and physical access restrictions. To enable Modbus TCP: 1.
InsightFacility Owner's Guide Configuring Devices Removing a Modbus Device To remove a Modbus device from InsightFacility: 1. Disconnect the device from the bus. 2. Log in to the InsightFacility web application. 3. Select the Devices tab and then navigate to the Modbus device that you want to remove. 4. Verify that the device is "Offline" and then click on the device. 5. Click Delete Device. 6. In the Delete Device dialog, click Delete. 7. Restart your InsightFacility (recommended).
Configuring Devices InsightFacility Owner's Guide Changing Device Settings Before making any changes, familiarize yourself thoroughly with the effects of changing the settings of another device. NOTICE RISK OF EQUIPMENT DAMAGE n Consult the device’s Owner’s Guide when changing the device’s settings. n Make sure the device connected on the Xanbus or Modbus network is in Standby mode before changing settings. n Do not change any settings unless you are familiar with the device.
InsightFacility Owner's Guide Configuring Devices Figure 25 Sample Device Overview screen - List display To change a device setting: 1. In the main menu bar, click Devices. See Figure 24 for a sample of the default display of all connected devices. 2. If you want a shorter list of devices, switch to a List display. See Figure 25. 3. Put the device in to Standby mode first. a. Click a device you want to put in to Standby mode. b. Click Configuration > Controls.
Configuring Devices InsightFacility Owner's Guide Device Association This procedure describes how to set device associations from the InsightFacility web application. To associate devices: 1. In the main menu bar, click Devices and then select the device type from the left menu. 2. Select a device. 3. On the device page, select Configuration and then click Advanced. 4. Click Associations to expand the section. 5. Select the correct association(s) from the drop-down menu(s). 6. Click Apply. 7.
InsightFacility Owner's Guide Configuring Devices Cloud Settings To use InsightCloud for remote monitoring and configuration, you must configure the Cloud connection for your InsightFacility. The Cloud settings screen can be used to check your Cloud connectivity. To configure the Cloud connection for your InsightFacility: 1. Go to Setup > Network > Cloud settings. 2. Beside “Cloud enable”, select the Enable radio button. 3.
Configuring Devices InsightFacility Owner's Guide Configuring an AC-Coupled System This procedure describes how to associate a PV inverter's point of coupling in an ACcoupled system. To configure an AC-coupled system: 1. In the main menu bar, click Devices and then select the device type from the left menu. 2. On the device page, select Configuration and then click Advanced Device Settings. 3. From the drop-down menu, select either Load or Grid (depending on how your system is set up).
InsightFacility Owner's Guide Configuring Devices 3. Press OK. 4. Select a region from the Select Region drop-down menu. 5. Click Apply. To change grid code functions on specific devices: 1. Log in to the InsightFacility web application. 2. Go to Devices > Inverter/Chargers, and select your inverter model. 3. Click Grid Codes. 4. Go through the options in the Select Function drop-down menu and configure the settings below the graph.
Configuring Devices InsightFacility Owner's Guide 5. Click Apply. Enabling California Rule 21 n Source Requirements Document: RULE 21 Generating Facility Interconnection Smart Inverter Generating Facility Design and Operating Requirements - Section Hh Effective July 30, 2017 Instructions for Rule 21 Compliance To be California Rule 21 compliant, and for CEC compliance, upgrade your unit firmware to Version 1.0 or later, and update the Grid Code region in the InsightFacility desktop app.
InsightFacility Owner's Guide Configuring Devices 3. Press OK. 4. Select California Rule No 21-2018 from the Select Region drop-down menu. 5. Click Apply. To change grid code functions on specific devices: 1. Log in to the InsightFacility web application. 2. Go to Devices > Inverter/Chargers, and select your inverter model. 3. Click Grid Codes. 4. Go through the options in the Select Function drop-down menu and configure the settings below the graph.
Configuring Devices InsightFacility Owner's Guide 5. Click Apply.
5 Monitoring What's in This Chapter? Monitoring LED Indicators Startup Monitoring the Power Plant 65 65 65
InsightFacility Owner's Guide Monitoring Monitoring LED Indicators LED indicators allow you to monitor the functioning of the InsightFacility. Figure 26 Ports, buttons, and indicators Green Power The InsightFacility is powered on. Green Memory Device is logging data to internal memory when flashing. Red Event Devices on the Power system have events to report. Startup The Power LED flashes slowly when the InsightFacility application is loading and flashes quickly during application initialization.
Monitoring InsightFacility Owner's Guide Figure 27 Dashboard 1 Power flow tab – shows an interactive and graphical view of the power plant with its different connected devices. Battery summary tab – shows a historical line graph of four battery metrics such as 2 current, volts, temperature, and state-of-charge (SOC). It shows one battery at a time. 3 Battery comparison tab – shows a historical and comparative line graph of the four battery metrics against all the different batteries.
6 Troubleshooting What's in This Chapter? Events 69
InsightFacility Owner's Guide Troubleshooting Events The events detected and monitored by InsightFacility vary in type. The types of events are categorized into warnings and detected faults. Warnings are displayed as orange icons with an exclamation point. Detected faults are displayed as red icons with an exclamation point. When devices detect an event that usually resolves by itself, it is still reported to InsightFacility and logged. It is logged under Historical (see Figure 29 ).
Troubleshooting InsightFacility Owner's Guide Figure 28 Active events Figure 29 Historical events To view Events: 1. In the main menu bar, click Events. The Active events are displayed first in the main display board.
InsightFacility Owner's Guide Troubleshooting 2. Click Historical to view events that have been logged and/or resolved. 3. To download a copy of the events, click the CSV icon on the lower right hand corner of the main display board.
7 Specifications What's in This Chapter? Electrical Specifications 73 Physical Specifications 73 Features 74 Regulatory 74 FCC Regulatory Compliance 74 ISED Regulatory Compliance 75 Simplified EU Declaration of Conformity 76 Schneider Electric Products that Work with the InsightFacility 76 Dimensions 77
InsightFacility Owner's Guide Specifications Electrical Specifications NOTE: Specifications subject to change without prior notice. NOTICE EQUIPMENT DAMAGE Do not power the unit without first installing the supplied antennas. Failure to follow these instructions can result in equipment damage. Power Consumption 2 W average / 10 W peak AC/DC adapter Input: 100-240 V AC, 50-60 Hz, 0.48 A, Output: 12 V DC, 1.6 A, 5.5 mm outer, 2.1 mm centerpositive jack. NOTE: Required when used with the Conext SW.
Specifications InsightFacility Owner's Guide Features NOTE: Specifications subject to change without prior notice. Programmable dry contact relay Screw 3-terminal, 16-24 AWG, NC-Com-NO, Form: Class 2, 24 V DC, 4 A max SELV input only Web-base user interface Internet Browser Remote firmware upgrades Yes (InsightFacility and connected Xanbus devices) Regulatory NOTE: Specifications subject to change without prior notice.
InsightFacility Owner's Guide Specifications Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Specifications InsightFacility Owner's Guide Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé. Cet émetteur ne doit pas être situé ou fonctionner conjointement avec une autre antenne ou un autre émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
InsightFacility Owner's Guide Specifications Dimensions NOTE: Specifications subject to change without prior notice.
A Installing the InsightFacility Security Certificate What's in This Chapter? Root Certificates 79
InsightFacility Owner's Guide Installing the InsightFacility Security Certificate Root Certificates InsightFacility does not support 3rd party root certificates as it is a server on your local area network with a potentially dynamic IP address and no public server name. As a result, web browsers will pop up a warning message similar to the one shown below1 : In order to connect to the InsightFacility local web page you must confirm the warning and tell the browser that it is ok to connect to the gateway.
Schneider Electric As standards, specifications, and designs change from time to time, please ask for confirmation of the information given in this publication. For other country details please contact your local Schneider Electric Sales Representative or visit the Schneider Electric Solar Business website at: http://solar.schneider-electric.com/ © 2021 Schneider Electric. All Rights Reserved.
