Conext SW 4024-120 Install Guide
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0639-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Installation
- Materials List
- Conext SW Front and Side Panels
- Conext SW Supplied Accessories
- Conext SW Required Accessory
- Installation Information
- Before You Begin the Installation
- Installation Codes
- Xanbus Network System
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Installation Planning
- Planning Preparations
- Components of the Inverter Power System
- Unpacking and Inspecting the Conext SW Inverter/Charger
- Installation Tools and Materials
- Inverter/Charger Installation
- Overview
- Step 1: Choosing a Location for the Inverter/Charger
- Step 2: Mounting the Inverter/Charger
- Step 3: Connecting the AC Input and AC Output Wires
- AC System Bonding
- Step 4: Installing the DC Switchgear and Connecting the DC Cables
- Step 5: Connecting the BTS and Xanbus-enabled Components
- Step 6: Performing Checks Prior to Initial Start-Up
- Step 7: Testing Your Installation
- Battery Information
- Battery Bank Sizing
- Estimating Battery Requirements
- Restrictions on Motor Size
- Battery Cabling and Hook-up Configurations
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
- Wiring Diagrams
- Single-Inverter System (Off-Grid/Power Backup)
- Single-Inverter System Renewable Energy (Solar)
Physical Specifications
975-0639-01-03 2–5
This guide for use by qualified personnel only
Physical Specifications
Environmental Specifications
SW 2524 120/240 SW 4024 120/240 SW 4048 120/240
L × W × H
15.2×13.5×7.6 in
(387×343×197 mm)
15.2×13.5×7.6 in
(387×343×197 mm)
15.2×13.5×7.6 in
(387×343×197 mm)
Unit Net
Weight
50.7 lbs. (23 kg) 67.2 lbs. (30.5 kg) 67.2 lbs. (30.5 kg)
All Models
Nominal ambient temperature 77 °F (25 °C)
Operating temperature range
–4 to 140 °F (–20 to 60 °C)
starts derating above 77 °F (25 °C) (see following graph)
Storage temperature range –40 to 185 °F (–40 to 85 °C)
Humidity: Operation/Storage 95% RH, non-condensing
Ingress protection rating Indoor only, IP 20
Pollution degree 3
Over voltage category (AC mains) CAT III
Altitude: Operating 6,562 ft. (2,000 m)
Mounting wall mount using installation bracket
Figure 2-1 Output Power versus Temperature Derating Graph
-20 -10 0 5 10 15 20 25 30 35 40 45 50 55 60 °C
-4 14 32 41 50 59 68 77 86 95 104 113 122 131 140 °F
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
W
SW 4024 120/240
SW 2524 120/240
Full power at ambient
3400W
2800W
2500W
3000W
3800W
3600W
3400W
3200W
SW 4048 120/240
3200W
2750W