Mupgrade Utility For Network Management Cards User Manual NMC Transverse 66074 Mupgrade - User Manual NMC Teleservice 66124 34003662EN/CA NMC with ModBus/Jbus 66123 Page 1/18
Mupgrade Utility For Network Management Cards User Manual Table of Contents 1 Introduction_____________________________________________________ 3 2 Installation______________________________________________________ 3 3 Best environment to use it_________________________________________ 3 4 Compatibility ____________________________________________________ 4 4.1 Cards compability ________________________________________________ 4 4.
Mupgrade Utility For Network Management Cards User Manual 1 Introduction This document describes how to use the Network Management Card Firmware Utility software (Mupgrade) to discover, upgrade and configure Network Management Cards linked to the network. The following functions are available: - Auto-discovery of your installed base (Model card, IP address, MAC address, firmware card release embedded…) - Direct link to the card Web interface.
Mupgrade Utility For Network Management Cards User Manual 4 Compatibility 4.1 Cards compability MUPGRADE is compliant with following cards: 66074 < FB Yes 66074 ≥ FB Yes Internet link Yes Yes Firmware upgrade Yes Yes Configuration management No Yes No Export / import list of installed base Yes Yes Yes Discovery Notes. (1) 66123 and 66124 Yes Yes No (1) : the firmware upgrade is available directly from the card web page.
Mupgrade Utility For Network Management Cards User Manual 4.2 Firmware compability For the 66074 NMC, there is and lost of compability between hardware and firmware. Firmware upgrade 66074 Technical Level < 12 Green PCB 66074 Technical Level ≥ 12 Blue PCB Last firmware release: GF First firmware release: HA So it is not possible to upgrade an 66074 NMC at technical level < 12 (green PCB), with a firmware equal or upper release HA.
Mupgrade Utility For Network Management Cards User Manual 5 Operations description 5.1 Start and Stop Mupgrade Once installed, use the Mupgrade shortcut placed in the program menu to launch the software.
Mupgrade Utility For Network Management Cards User Manual 5.2 Discovering the Network Management Cards Autodiscovery is based on a TFTP broadcast. Access to cards which belong to another group can be limited by routers and switches configuration. Click on the button Discover and wait the end of the research. To see more information about the cards select Show All Informations box.
Mupgrade Utility For Network Management Cards User Manual 5.3 Display the NMC Card by class (66074, 66123, 66124) For displaying the king of NMC card, it is necessary to click on the “Show All information” box.
Mupgrade Utility For Network Management Cards User Manual 5.4 Enter Username and Password - - For a single card : Select a line and click on « Modify » or double click on the line For several cards : Select all the cards you need by using the keys : CTRL, SHIFT, TAB, SPACE and click on the title area of the column Username and Password to enter Username and Password By default, Username/Password is MGEUPS/MGEUPS.
Mupgrade Utility For Network Management Cards User Manual 7 Upgrade the Network Management Card firmware Download the last firmware release from the www.apc.com Web site. To upgrade the card firmware: 1. Load the new firmware file by clicking on Open button inside the « Firmware Upgrade » page. 2. Verify you have loaded the good release in the « Version No » window. 3. Select the card(s) you want to upgrade. 4. Check that Username and Password are filled in.
Mupgrade Utility For Network Management Cards User Manual 5. Click on Upgrade button and after on OK to send the new firmware to the cards. 6. Upgrading leaves about 30 seconds / card (depend on traffic network). When it is finished, the card restarts and a similar pop-up appears : Note: 1. You can select a large number of UPSs at the same time, Mupgrade will manage download operation by group of 4 UPSs. 2. Check on the firmware release note if specific operations are needed after a firmware upgrade.
Mupgrade Utility For Network Management Cards User Manual 8 Remote Configuration The Remote configuration function allows you to import, modify and export configuration (settings) from and to Network Management Cards. Four steps to configure all your Network Management Cards: 1. Configure a Network Management Card located on the network through the html interface to create a master configuration. Refer to the Network Management Card user manual for details. 2. Import this configuration from the master card.
Mupgrade Utility For Network Management Cards User Manual 8.1 Import configuration This function permit to import (upload) all the parameters managed in the Network Management Card Web interface: 1 - Select the Remote Configuration tab. 2 – Select the card that will be the master 3 – Click on “Browse” to open the card Web interface and make the changes you want. Then save your modifications 4 – Click on “Import” to upload the configuration file, from the master card.
Mupgrade Utility For Network Management Cards User Manual 8.2 The configuration editor At end of the import, the configuration editor opens automatically. It allows you to edit, change or mask some parameters to prepare your configuration to be exported to your installed UPS / STS base. The names of the items are the same than in the Network Management Card Web interface. The following syntax is used: Box is not checked: the page / data will not be overwritten when exporting the file.
Mupgrade Utility For Network Management Cards User Manual 2.STS configuration editor . Same feature than UPS configuration. Only present, global NMC settings. All the specifics settings for UPS are absents.
Mupgrade Utility For Network Management Cards User Manual Export configuration This function permit to export (download) all the parameters managed in the Network Management Card Web interface. Be sure, you are inside the Remote Configuration page. 3 - Select the lines corresponding cards to be configured. 2 – Check the configuration information. The configuration ID, also. It will be display after the end of export phase.
Mupgrade Utility For Network Management Cards User Manual 6. Export leaves about 5 seconds / card (depend on traffic network). When it is finished, the card restarts and a similar pop-up appears : The configuration file are now applied, with the Configuration ID Note: You can select a large number of UPSs at the same time. Mupgrade will manage download operation by group of 4 UPSs.
Mupgrade Utility For Network Management Cards User Manual 9 Miscellaneous 9.1 Icon description in the UPS list The icon on the left part of the UPS List gives an indication of the model card and its status: Icon - Mupgrade - User Manual Definition Web compliant The card is ready to upgrade Upgrade image is suitable for this card (Note: The background color is white) Web compliant The card’s ‘Network Upgrade’ setting is set to “Disabled».