Installation Guide
Table Of Contents
- Conext™ XW+ Inverter/Charger Installation Guide
- Conext™ XW+ Inverter/Charger Installation Guide
- About This Guide
- Important Safety Instructions
- Contents
- Introduction
- Overview
- Optional Accessories
- Conext XW+ Conduit Box
- Conext XW+ Power Distribution Panel
- Conext XW+ Connection Kit for INV2 INV3 PDP
- Conext 120/240VAC Breaker Kit for Conext XW+ PDP
- Conext MPPT 60 150 Solar Charge Controller
- Conext MPPT 80 600 Solar Charge Controller
- Conext System Control Panel
- Conext Automatic Generator Start
- Conext ComBox
- Conext Battery Monitor
- Conext 3 Phase Breaker Kit for Conext XW+ PDP
- 100A, 125VDC Breaker Master Pack (12 units)
- 80A, 125VDC Breaker Master Pack (12 units)
- 60A, 160VDC Breaker Master Pack (48 units)
- 250A, 160VDC Breaker Master Pack (6 units)
- Pre-Installation and Wall-Mounting
- Wiring the Conext XW+ Inverter/ Charger and Conext XW+ Power Distribution Panel
- Removing the AC Access Panel and PDP Internal Faceplates
- Communication Ports and BTS Port
- Wiring the Conext XW+ Inverter/Charger with a PDP
- Basic Functional Test – Single Inverter
- Wiring Additional Conext XW+ units with a PDP
- Basic Functional Test - Multiple Inverters
- Wiring a Balanced Three-Phase System
- Wiring the Conext XW+ Inverter/Charger without a PDP
- Xanbus Network Installation
- Conext XW+ Inverter/Charger Accessories Installation
- Specifications
- Wiring Diagrams
- Split-Phase to Single-Phase Conversion Instructions
Contents
xvi 975-0239-01-01 Rev G
This manual is for use by qualified personnel only
Installing the Network ------------------------------------------------------ 4–4
Before You Begin the Installation ------------------------------------------- 4–5
Installation Tools and Materials -------------------------------------------- 4–5
Installing AC sync and Xanbus cables --------------------------------------- 4–5
Guidelines for Routing the Xanbus Cables ------------------------------------ 4–7
5 Conext XW Series Optional Accessories Installation
Conext Combox Installation ------------------------------------------------- 5–2
Conext System Control Panel Installation ---------------------------------------- 5–2
Installing the SCP via the Xanbus Network ------------------------------------ 5–3
Replacing the Inverter Information Panel with the SCP ---------------------------- 5–4
Verifying the Installation ------------------------------------------------- 5–7
A Specifications
Electrical Specifications ---------------------------------------------------- A–2
Grid-tie Specifications --------------------------------------------------- A–3
Conext XW+ Series Inverter/Charger Overload Capability -------------------------A–4
Conext XW+ 6848 NA AC Overload Capability ------------------------------ A–4
Conext XW+ 5548 NA AC Overload Capability ------------------------------ A–4
Output Power Versus Ambient Temperature -----------------------------------A–5
Conext XW+ Series Inverter/Charger Efficiency --------------------------------- A–6
Inverting Efficiency (Typical) -------------------------------------------A–6
Charging Efficiency (Typical) ------------------------------------------- A–6
Charging Power Factor ----------------------------------------------- A–7
Grid-tie Sell Mode Efficiency (Typical) ------------------------------------ A–7
Mechanical Specifications --------------------------------------------------A–8
Accessories------------------------------------------------------------- A–9
B Wiring Diagrams
Single-Inverter System (Backup Only) Without a Conext XW+ Power Distribution Panel ------- B–3
Single-Inverter System (Backup Only) With a Conext XW+ Power Distribution Panel --------- B–4
Single-Inverter System Renewable Energy (Solar)---------------------------------- B–5
Dual-Inverter System Renewable Energy (Solar) ----------------------------------- B–6
C Split-Phase to Single-Phase Conversion Instructions
Converting 120 V/240 V Split-Phase to 120 V Single-Phase ---------------------------C–2
Installation Tools and Materials --------------------------------------------C–2
Disconnecting Power Sources ---------------------------------------------C–3
AC Access Panel Removal -----------------------------------------------C–3
Reconfiguring the Secondary Transformer Wires on X1 and X2 Connectors ------------C–4
Reconfiguring the AC Ports on the Load, AC1, and AC2 Connectors -----------------C–6
Upgrading the Firmware -------------------------------------------------C–7
Updating the Label -----------------------------------------------------C–8