Installation Guide
Table Of Contents
- Conext™ XW+ Inverter/Charger Installation Guide
- Conext™ XW+ Inverter/Charger Installation Guide
- About This Guide
- Important Safety Instructions
- Contents
- Introduction
- Overview
- Optional Accessories
- Conext XW+ Conduit Box
- Conext XW+ Power Distribution Panel
- Conext XW+ Connection Kit for INV2 INV3 PDP
- Conext 120/240VAC Breaker Kit for Conext XW+ PDP
- Conext MPPT 60 150 Solar Charge Controller
- Conext MPPT 80 600 Solar Charge Controller
- Conext System Control Panel
- Conext Automatic Generator Start
- Conext ComBox
- Conext Battery Monitor
- Conext 3 Phase Breaker Kit for Conext XW+ PDP
- 100A, 125VDC Breaker Master Pack (12 units)
- 80A, 125VDC Breaker Master Pack (12 units)
- 60A, 160VDC Breaker Master Pack (48 units)
- 250A, 160VDC Breaker Master Pack (6 units)
- Pre-Installation and Wall-Mounting
- Wiring the Conext XW+ Inverter/ Charger and Conext XW+ Power Distribution Panel
- Removing the AC Access Panel and PDP Internal Faceplates
- Communication Ports and BTS Port
- Wiring the Conext XW+ Inverter/Charger with a PDP
- Basic Functional Test – Single Inverter
- Wiring Additional Conext XW+ units with a PDP
- Basic Functional Test - Multiple Inverters
- Wiring a Balanced Three-Phase System
- Wiring the Conext XW+ Inverter/Charger without a PDP
- Xanbus Network Installation
- Conext XW+ Inverter/Charger Accessories Installation
- Specifications
- Wiring Diagrams
- Split-Phase to Single-Phase Conversion Instructions
Wall-Mounting
975-0239-01-01 Rev G 2–7
This manual is for use by qualified personnel only
Each Conext XW+ and PDP requires a separate mounting plate. Attach the
mounting plate to the wall before you attach the Conext XW+ or PDP to the
mounting plate.
Each mounting plate requires a minimum of four ¼-inch diameter lag bolts or
other fasteners (not included).The fasteners must be strong enough to support
500 lbs (227 kg).
The type of fastener required to secure the mounting plate varies according to
the vertical surface and wall structure of your installation location. For a list of
recommended fasteners, see Table 2-1, below.
Table 2-1 Recommended fasteners
The holes of each mounting plate are spaced 16 inches (40 cm) apart, so that
the mounting plate will span two wall studs spaced 16 inches on-center.
Additional mounting holes are provided to allow for other mounting options.
Structure Required Fastener Screws Per Plate
Wood studs at 16" on-center (O.C.) 1/4" Ø × 3 1/2" long lag
screw
Four
Wood studs not at 16" O.C. (3/4" minimum
plywood panel required)
1/4" Ø × 1" long wood screw Six
Steel studs at 16" O.C. (minimum 18 gauge) 1/4" Ø self-drilling screw Four
Figure 2-4 Mounting plate dimensions
Note: If the wall does not have 16-inch (40 cm) on-center studs, you will need to
provide adequate support for the mounting plates. For example, a sheet of
plywood can be attached to the wall, and the mounting plates can then be
attached to plywood.
16”
4 ½”
2”
6”
1 ¾”
17”
6
7
8
”9
3
16
”
2 ¼”
¾”