USB ZB Interface Unit Ethernet ZB Interface Unit 5200UZI WHC2_5921 5200EZI WHC2_5922 User’s Manual
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual Contents 1.0 Package Components ....................................................................................3 2.0 Safety and Product Handling Instructions ...................................................4 3.0 Introduction ....................................................................................................5 3.1 What is a ZigBee Network? ...........................................
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 1.0 Package Components The package components for the USB ZB Interface Unit and the Ethernet ZB Interface Unit are shown below. 5200UZI WHC2_5921 USB ZB Interface Unit 5200EZI WHC2_5922 Ethernet ZB Interface Unit 5200EZI WHC2-5922 Power supply and AC Adapter for Australia and New Zealand Category 5e Network Cable Figure 1.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 2.0 Safety and Product Handling Instructions The ZigBee Interface units are for indoor use only. The units are designed for use with a PC or with a Wiser Home Control. Please read and follow these safety Cautions and Warnings. Warning. Automatic Control Device Equipment controlled by this device may start or stop at any time without warning.
200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 3.0 Introduction The ZB interface unit provides a wireless connection between a PC and an existing ZigBee network. The interface unit has the following capabilities: • The ZB interface unit can connect to an existing ZigBee network using E-mode (easy mode).
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 3.2 5200UZI WHC2_5921 USB ZB Interface The USB type interface is normally plugged directly to a USB port on a PC or to the special port provided in the Wiser Home Control Mk 2. The interface unit is powered by the active USB port. When the interface unit is powered on it can connect to (join) an existing ZigBee network using E-mode. A freestanding PC can be used.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 3.3 5200EZI WHC2_5922 Ethernet USB Interface The Ethernet ZB interface is connected to a router or switch on the local Ethernet network. A network patch cable is provided with the unit. Use only the supplied AC power supply to power the unit. The PC that has Zoolkit software loaded is connected to the same network (VLAN) as the interface unit.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 4.0 Switch Buttons and Indicators The switch buttons and indicators (LEDs) are used during connection to the network and also provide status information. Figure 6 shows the location of the buttons and LEDs on the interface units.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 5.0 Installation The installation steps for the USB and Ethernet ZB interfaces differ slightly. The following sections tell you how to install the type of interface you are using. This User’s Manual assumes that you have a working ZigBee network and that you have access to the CIS Web site on the Internet.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 4. USB ZB Interface and Ethernet ZB Interface User’s Manual Press and release the Setup button. This causes the interface unit to attempt to join the ZigBee network using E-mode. The ZigBee status LED should be in an orange -flashing state and then switch to the green - continuous state. USB ZB Interface 5200UZI WHC2_5921 Wiser Home Control Mk 2 Figure 7. USB ZB Interface installation in a Wiser Home Control 5.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 5.2 Ethernet ZB Interface Read the requirements before installing the Ethernet ZB Interface. Requirements • Load the Zoolkit software application and the Control System IP Utility on the PC. The software setup programs can be freely downloaded from the CIS Web site: http://www.clipsal.com/cis/ On the Technical page, select Downloads. • A power outlet is required for the power supply.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 6.0 Commissioning and Troubleshooting The Zoolkit Wizard follows a series of steps using dialog windows that require your input. The user interface is similar to many other applications. The Zoolkit application does the following: • Loads device drivers on the PC as needed. • Starts up the Zoolkit user interface (UI) and a wizard to guide you through various tasks.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 6.2 Reset Button Using the reset button on the USB ZB interface will reset the ZigBee network configuration settings. To reset the ZigBee network configuration settings on the Ethernet ZB interface unit, press and hold the SETUP button for a long-press, at least 5 seconds. Before pressing the reset button, try powering the ZB interface off and on again. to restore connectivity.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 7.0 Specifications 7.1 5200UZI WHC2_5921 USB ZB Interface Parameter Description Device type PC to ZigBee network interface PC connection Active USB port (power sourced from PC) WHC connection Dedicated port for USB ZB Interface (power sourced from WHC) Wireless ZigBee compliant Radio frequency 2.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 7.2 5200EZI USB ZB Interface and Ethernet ZB Interface User’s Manual WHC2_5922 Ethernet ZB Interface Parameter Description Device type Ethernet to ZigBee network interface Ethernet connection Ethernet modem or router Power supply AC power adapter, input voltage 100 to 240V a.c., input frequency 50/60Hz, output 24 V d.c. 1.25A, manufacutrer FranMar, model number FRA030E-S241 Wireless ZigBee compliant Radio frequency 2.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 8.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 9.0 Installation Notes Site Location Installer information Interface Unit Product ID: Serial Number: MAC: IP Address: ZB network: Other details: Interface Unit Product ID: Serial Number: MAC: IP Address: ZB network: Other details: Interface Unit Product ID: Serial Number: MAC: IP Address: ZB network: Other details: 18 of 20 © 2012 Schneider Electric. All Rights Reserved.
5200UZI WHC2_5921 and 5200EZI WHC2_5922 USB ZB Interface and Ethernet ZB Interface User’s Manual 10.0 Two-Year Warranty The USB and Ethernet ZB Interface units are covered by a two-year warranty against manufacturing defects.
Schneider Electric (Australia) Pty Ltd Contact us: clipsal.