User's Guide Matrix Switcher SLC5608842E and SLC5608842 for Use with C-Bus™ Multi Room Audio Systems Instruction Bulletin Retain for future use.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
63249-420-266A2 06/2010 Matrix Switcher User's Guide PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. This document is not intended as an instruction manual for untrained persons. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this manual. FCC CLASS B This device complies with Part 15 of the FCC Rules.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 PRODUCT LABEL Refer to the warning label appearing on the product illustrated below. Refer to the "Notices" section at the beginning of this bulletin for definitions of the symbols appearing on the label. Carefully read and follow the safety precautions both on the equipment and contained in this bulletin before attempting to install or maintain electrical equipment.
63249-420-266A2 06/2010 Matrix Switcher User's Guide INTRODUCTION This User's Guide provides information about operating and maintaining the Multi Room Audio (MRA) Matrix Switcher. Refer to the MRA Remote Amplifier User's Guide for more information about operating and maintaining MRA Remote Amplifiers. The MRA system includes a Matrix Switcher, and audio amplifiers. Some of the amplifiers may use external power supplies.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 About the MRA System The Multi Room Audio System is installed in rooms with audio sources such as an audio/video (A/V) receiver, a CD player and a TV set top box. Digital audio connections on the Matrix Switcher send program material to the MRA amplifiers. The Matrix Switcher distributes the selected program material to each of the amplifiers in the system.
63249-420-266A2 06/2010 Matrix Switcher User's Guide Table 1: Matrix Switcher Front Panel Features Connection/Indicat Description or Function or USB connector port socket 1 – Type A (Deluxe Matrix Switcher model only) Allows MP3 files to be played from a device such as a USB drive using the streaming audio feature on the Deluxe Matrix Switcher. The front USB port operates independently from the USB socket located on the rear panel. LCD screen Shows the program selection choices.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 SAFETY PRECAUTIONS This section contains important safety precautions that must be followed before attempting to install or maintain electrical equipment. Carefully read and follow the safety precautions below. HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E.
63249-420-266A2 06/2010 Matrix Switcher User's Guide There are no user serviceable parts inside the Matrix Switcher enclosure. Replacing the fuse does not require opening the unit cover. Installation should typically be performed by a C-Bus installer. HAZARD OF ELECTRIC SHOCK, BURN, OR ARC FLASH Use only the power supply and cords supplied with the units. Do not substitute power supplies or electrical cords. Plug the unit's power cord into a properly-grounded AC power outlet.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 The Matrix Switcher Rear Panel The installer typically completes rear panel connections. Refer to the figure and table below to check cable connections to the rear panel. Many network cables appear similar but have different electrical properties. The equipment can be damaged if cables are plugged into the wrong port. Consult your system installer for proper cable connections.
63249-420-266A2 06/2010 Matrix Switcher User's Guide Table 2: Rear Panel Features Connection/Indicator Description or Function Power switch Switches the unit on and off. Infrared Outputs (IR OUT 2 – 3.5 mm) These 3.5 mm sockets connect to IR Emitter leads. IR Emitters are then coupled to IR receivers on A/V equipment to provide remote control from any zone. Digital Audio Outputs 8 – RJ45 Each zone output is used to connect the Matrix Switcher to one amplifier in each audio zone.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 The amplifiers can produce sounds loud enough to cause permanent hearing loss. HAZARD OF PERMANENT HEARING LOSS Keep volume controls at low levels when selecting program sources or when connecting local audio sources to an MRA amplifier. Plug the headphones into the MRA amplifier before placing the ear pieces on your head or in ears. Do not allow children to use the MRA equipment without adequate supervision.
63249-420-266A2 06/2010 Matrix Switcher User's Guide GENERAL USE GUIDELINES General installing, cabling and programming tasks and are described in the C-Bus™ Multi Room Audio Matrix Switcher Installation instruction bulletin, other component instruction bulletins, and in the software Help files. Follow the guidelines below for general use of the Matrix Switcher. Leave the equipment powered ON when not in use. The MRA system uses very little power when not being actively used.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 Selecting a Program for an Audio Zone Listed below are several ways to change a zone’s input source in a typical MRA system installation. A zone selection button on the Matrix Switcher The Source selection buttons on a Desktop Amplifier An infrared (IR) remote control used with a Desktop Amplifier An appropriately configured C-Bus wall switch or touch screen.
63249-420-266A2 06/2010 Matrix Switcher User's Guide Annunciation (Optional) The Matrix Switcher has the capability of announcing the name of an input source whenever it is selected. Annunciation provides instant feedback when changing the source selection using a C-Bus switch, amplifier or remote control. Annunciation is broadcast through the speakers in the zone where the input source has changed. Using MARPA configuration software, the installer can disable this feature.
Matrix Switcher User's Guide 63249-420-266A2 06/2010 MAINTENANCE AND TROUBLESHOOTING Replacing the Fuse Other than the fuse, there are no other user serviceable parts inside the Matrix Switcher. If fuse replacement is required, always use the correct fuse listed on the rear panel. Follow the steps below to replace the fuse. Turn off the power switch and unplug the unit. Locate fuse holder adjacent to the cord connector.
63249-420-266A2 06/2010 Matrix Switcher User's Guide SPECIFICATIONS Table 3: Specifications – Matrix Switcher Parameter Description Supply Voltage 120 Vac Mains frequency range 47 to 53 Hz and 57 to 63 Hz Power consumption 220 VA maximum C-Bus network voltage 15 to 36 Vdc C-Bus sink current 22 mA; the matrix switcher does not supply current to the network C-Bus AC input impedance 80 kΩ @ 1 kHz Network clock and burden Software selectable Source input signal level 2.
Matrix Switcher Instruction Bulletin SUPPORT AND SERVICE Contact the Customer Information Center for technical support by phone at 1-888-778-2733 or e-mail at lightingcontrol.support@us.schneider-electric.com. Contact your local Schneider Electric service representative or CBus™ system certified installer for repairs or service to your network. You may also find helpful information on our web site at www.Schneider-Electric.us.
