Installation Guide

975-0717-01-01 Revision A
04-2014
1
Contact Information
www.schneider-electric.com
Please contact your local Schneider Electric Sales Representative or visit the Schneider Electric website at:
http://www.SEsolar.com
www.SEsolar.com
Conext System Control Panel Installation Guide
865-1050-01
Installer Provided Tools and Materials:
• Phillips head screwdriver
• Jigsaw or small keyhole saw
• Cable clamps or hardware fasteners
• Power drill with 1/8" bit (optional)
Xanbus cable
This Guide is intended for anyone who needs to operate, configure, and troubleshoot the Conext System Control Panel
(SCP). Certain configuration tasks should only be performed by qualified personnel in consultation with your local utility
and/or an authorized dealer. Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. Servicing of batteries must only be performed or supervised by qualified personnel with knowledge
of batteries and their required precautions.
Qualified personnel have training, knowledge, and experience in:
• Installing electrical equipment
• Applying applicable installation codes
• Analyzing and reducing the hazards involved in performing electrical work
• Installing and configuring batteries
• Selecting and using Personal Protective Equipment (PPE)
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
B
Materials List
Mounting template sticker
Mounting plate for
flush mounting
Network terminator
4 x #6 (M3)
self-tapping screws
2 x #8 (M4)
self-tapping screws
Mounting bracket for
surface mounting
Standby
Event/Warning
Conext SCP
System Control Panel (SCP)
MOUNTING TEMPLATE
FOR SURFACE MOUNTING:
A) MARK LOCATIONS FOR MOUNTING SCREWS
B) DRILL 1.375" (35mm) HOLE FOR COMMUNICATION CABLES
FOR FLUSH MOUNTING, CUT ALONG DASHED LINES
CUTOUT SIZE: 6" X 4" (152.4mm x 101.3mm)
Standby
Event/Warning
Conext SCP
• Selects a menu item
• Displays the next screen
Standby
• Scrolls up a line of text
• Increases a selected value
• Displays the previous device home screen
• Scrolls down a line of text
• Decreases a selected value
• Displays the next device home screen
• Cancels selection of a menu item
• Displays the previous screen
• Disables inverting and charging on all
inverter/chargers in the system when
pressed for one to two seconds.
To configure device settings
To display device status
In the System Status screen, press down
arrow to display device Home screens. The
inverter/charger is the first Home screen by
default.
Select Device
System Settings
XW-MPPT60-150
XW SCP
XW6848 00
setup system
XW6848 00:Home
Status
Battery
Load
AC1
Invert
-26.4A 51.9V
1250W
0.0V 0W
In the System Status screen, press Enter to
display the Select Device screen.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E
or CSA Z462.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Never operate energized with covers removed
• Energized from multiple sources. Before removing covers identify all sources, de-energize, lock-out, and tag-out
and wait 2 minutes for circuits to discharge
• Always use a properly rated voltage sensing device to confirm all circuits are de-energized.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Batteries can present a risk of electric shock and high short-circuit current. The following precautions must be
observed when working with batteries:
• Remove watches, rings or other metal objects.
• Use tools with insulated handles.
• Wear protective glasses, gloves and boots.
• Do not lay tools or other metal parts on top of batteries.
• Disconnect the charging source prior to connecting or disconnecting battery terminals.
Failure to follow these instructions will result in death or serious injury.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Battery Circuit Breakers must be installed according to the specifications and requirements specified by
Schneider Electric.
• Servicing of batteries must only be performed by qualified personnel and the required precautions. Keep
unqualified personnel away from batteries.
Failure to follow these instructions will result in death or serious injury.
A
Important Safety Information
1. Before using the SCP, read all instructions and cautionary markings on the unit and all appropriate
sections of this manual.
2. Use of accessories not recommended or sold by the manufacturer may result in a risk of fire, electric shock, or
injury to persons.
3. The SCP is designed to be permanently connected to the Xanbus network. The manufacturer recommends that
all wiring be done by a certified technician or electrician to ensure adherence to the local and national electrical
codes applicable in your jurisdiction.
4. To avoid a risk of fire and electric shock, make sure that existing wiring is in good condition and that wire is not
undersized. Do not operate the SCP with damaged or substandard wiring.
5. Do not operate the SCP if it has been damaged in any way.
6. This unit does not have any user-serviceable parts. Do not disassemble the SCP except where noted for
connecting wiring and cabling. See your warranty for instructions on obtaining service. Attempting to service the
unit yourself may result in a risk of electrical shock or fire. Internal capacitors remain charged after all power is
disconnected.
7. To reduce the risk of electrical shock, disconnect connections from the SCP before attempting any maintenance
or cleaning or working on any components connected to the SCP. Putting the unit in Standby mode will not
reduce this risk.
8. Do not expose this unit to rain, snow, or liquids of any type. This product is designed for indoor use only. Damp
environments will significantly shorten the life of this product and corrosion caused by dampness will not be
covered by the product warranty.
9. To reduce the chance of short-circuits, always use insulated tools when installing or working with this equipment.
10. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with electrical
equipment.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
DANGER
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
WARNING
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
CAUTION
NOTICE is used to address practices not related to physical injury.. The safety alert symbol shall not be used with
this signal word.
NOTICE
A
Important Safety Information
Read and Save These Instructions - Do Not Discard
This guide contains important safety instructions for the Conext System Control Panel that must be followed during
installation procedures. Read and keep this Quick Start Guide for future reference.
Read these instructions carefully and look at the equipment to become familiar with the device before trying to install,
operate, service or maintain it. The following special messages may appear throughout this bulletin or on the
equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists
which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, SELLER
(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION
PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION;
(B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS, OR EXPENSES, WHETHER SPECIAL, DIRECT,
INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF
ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK, AND
(C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO
MAINTAIN THE ACCURACY OF THE TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED, APPROVED CONTENT IS
CONTAINED WITH THE ENGLISH LANGUAGE VERSION WHICH IS POSTED AT WWW.SCHNEIDER-ELECTRIC.COM.
Standby
Event/Warning
Conext SCP
C
Using the System Control Panel – Basics
System Status
menu
Battery 20.4A 53.9V
AC1 115V 3202W
BatLev E--F
Load 1235W
9:18AM Mar 10