Installation Guide

ManualsBrandsSchneider ManualsVBBSchneider SpaceLogic VBB/VBS

Document Number: F-27393-16

www.schneider-electric.com

schneider-electric.com | 1Installation Instruction

SpaceLogic VBB/VBS

Ball Valves with Floating Actuators

Inspection

Inspect the package for damage. If package is damaged,

notify the appropriate carrier immediately. If undamaged, open

the package and inspect the device for obvious damage.

Return damaged products.

Requirements

RISK OF EQUIPMENT DAMAGE

• Read and understand these instructions before installing or

servicing this product.

• Do not install this product in hazardous or classified

locations unless expressly permitted.

• Turn off all power supplying equipment before working on

the product.

• Make all connections in accordance with the electrical wiring

diagram.

• Do not exceed the product’s technical ratings.

• Use copper conductors only. Make all connections in

accordance with the appropriate electrical wiring diagram.

• Avoid installation locations exposed to vibration, excessive

moisture, and/or corrosive or explosive vapours.

• Avoid electrical noise interference. Do not install near large

conductors, electrical machinery, or welding equipment.

• When making wiring connections within the actuator, do not

put leads or connectors below the motor.

• This product is a class 2 (Limited Voltage Limited Energy)

device.

• The installer is responsible for conformance to all applicable

codes.

• Check the Electrical terminals and any configuration switch

settings before powering up the actuator.

Failure to follow these instructions may cause equipment

damage.

If this product is used in a manner not speciﬁed by the manufacturer,

the protection provided by the product may be impaired.

No responsibility is assumed by Schneider Electric for any

consequences arising out of the use of this product.

NOTICE

Tools (not provided)

• Wrench/adjustable spanners 1”…1-5/8”

• Pipe wrench according to pipe size

• Volt-ohm multimeter

• Phillips Head screwdriver

Training and Other Accessories

• Installer must be a qualiﬁed, experienced technician

• Other accessories as appropriate.

Two-Way Valve: Flow A to AB Three-Way Valve: Mixing Only A

and/or B to AB.

M332A0x

M312A0x or M322A0x

Mounting

The valves can be mounted in horizontal or vertical piping.

When installed in horizontal piping, the actuator must be

above the valve body. When installed in horizontal piping the

actuator can be tilted left or right but it must not be tilted below

45° from vertical.

Vertical Pipe

Horizontal Pipe

Horizontal Plane

Summary of content (4 pages)

PAGE 1
Installation Instruction schneider-electric.com | 1 SpaceLogic VBB/VBS Ball Valves with Floating Actuators Inspection A Inspect the package for damage. If package is damaged, notify the appropriate carrier immediately. If undamaged, open the package and inspect the device for obvious damage. Return damaged products. AB B Two-Way Valve: Flow A to AB Requirements Three-Way Valve: Mixing Only A and/or B to AB.
PAGE 2
Installation Instructions schneider-electric.com | Piping NOTICE RISK OF EQUIPMENT DAMAGE • Do not install in open systems using substantial make-up water. • Follow proper water treatment practices and system procedures. Failure to follow these instructions may cause equipment damage. These valves must be piped according to the water flow diagram below. Two-Way valve flow should go A to AB. Threeway valves should be applied only as mixing valves (see diagram). 2 lock the manual lever in place.
PAGE 3
Installation Instructions schneider-electric.com | Field Repair 3 Power/Failure Action (Floating) Neither valve nor actuator are field repairable. Replace entire unit as necessary. Control Signal Position upon power loss Non-Spring Return Actuator Spring Return Open Actuator - Fail Open Spring Return Closed Actuator Fail Closed Maintain last position Will spring A to AB open Will spring A to AB closed Agency Listings North America: c-UL-us LISTED per UL 60730-1 & -2-14 and CSA E60730-1 &-2-14.
PAGE 4
Installation Instructions schneider-electric.com | 4 Dimensions (mm) 5-1/8 (130) 5-1/8 (130) 4-3/8 (111) 3/8 (10) 1/16 (2) 2-3/8 (60) 4-3/8 (111) 1/16 (2) 3-3/4 (95) 3-3/4 (95) 2-3/8 (60) 2-3/16 (56) 2 (50) 3/4 (19) 1-3/8 (35) 3/4 (19) 2-1/2 (64) 1-3/8 (35) 1-11/16 (43) 1-3/8 (35) 2-9/16 (65) 1-11/16 (43) 1-3/8 (35) 2-1/2 (64) 2-9/16 (65) Two-Way Non-Spring Return. Shipping Weight: 2.07 lbs (940 g) Three-Way Non-Spring Return. Shipping Weight: 2.