PARABOLIC MICROPHONE SYSTEM QUICK GUIDE INSTALLATION MANUAL , 12.06.2019 ASSEMBLY PLEASE LOCATE: SHIPMENT INCLUDES: 1 HANDLE (BLACK) INCLUDING THE FIXED MICROPHONE CABLE 1 RYCOTE MICROPHONE HOLDER (GRAY) INCL. MOUNTING KIT (GRAY TUBE, GRAY RING & BLACK RING) SECURED BACK OF RYCOTE MICROPHONE HOLDER.
IMPORTANT: PLEASE ALWAYS STORE ONLY DISH FOLDED IN GREEN SOFT CASE OR YOUR OWN HARD CASE UNFOLDED (HARD CASE FOR COMPLETE SYSTEM COMING END 2018) WITH THE REST OF THE SYSTEM IN THE ALREADY INCLUDED SMALL PELI HARD CASE. (PHOTO ABOVE: THE COMPLETE SYSTEM BEFORE ASSEMBLING) STEP 1. REMOVE THE MOUNTING KIT FROM THE RYCOTE MICROPHONE HOLDER AND ATTACH AS BELOW PHOTO TO DISH. GRAY TUBE THRU THE HOLE OF THE DISH WITH BLACK RING BACK OF THE DISH AND GRAY RING WITH THREAD AT THE INSIDE OF THE DISH.
(PHOTO: MOUNTING KIT SECURED) STEP 2. FASTEN AND SECURE THE HANDLE TO THE MOUNTING KIT HOLDING THE DISH USING THE KNOB.
STEP 3. SECURE THE HANDLE CYLINDER “STOPPER” ATTACHED TO CABLE INSIDE THE TUBE WITH THE CABLE GROMMIT ALIGNED BACK OF TUBE *PLACED AS PHOTO TIP! LOOSEN UP THE KNOB, PLACE CYLINDER INSIDE, THEN SECURE KNOB AGAIN. STEP 4. REMOVE THE FRONT CAP OF THE RYCOTE MICROPHONE HOLDER AND TAKE OUT THE BLACK FOAM COMPLETELY OUT OF THE HOLDER.
STEP 5. MOUNT & SECURE RYCOTE MICROPHONE HOLDER WITHOUT FOAM. (IMPORTANT: CABLE THRU THE HOLDER!) STEP 6. SLIDE THE FIXED CABLE OF THE HANDLE THRU THE SMALL HOLE BACK OF THE FOAM UNTIL THE CONNECTOR IS COMPLETELY THRU THE FOAM VISIBLE WITH CONNECTOR FRONT OF FOAM.
STEP 6. HANDLE CABLE CORRECTLY INSTALLED AND FOAM FIXED. (IMPORTANT: PULL GENTLY OUT THE CABLE ALLOWING TO MOUNT MICROPHONE AS NEXT STEP WITH A GENEROUS CABLE U-BEND) STEP 7. ATTACH AND LOCK THE SCHOEPS CCM MIC WITH THE THREAD SCREW.
STEP 8. PLACE AND SECURE THE SCHOEPS MICROPHONE INSIDE THE RYCOTE MICROPHONE HOLDER FOAM. MIC SHOULD BE FACING (POINTING) TOWARDS THE DISH INWARDS! IMPORTANT: MIC IN FOCUS ONLY WHEN THE BACK OF THE MIC BODY IS ALIGNED WITH THE FOAM AS PHOTO ABOVE. PLEASE ALLOW THE CABLE TO FORM A U-SHAPE. STEP 9. SECURE AGAIN FRONT CAP OF THE RYCOTE MIC HOLDER.
SYSTEM READY! CONNECT ONLY A STANDARD BALANCED XLR MICROPHONE CABLE FROM BOTTOM OF THE HANDLE TO YOUR RECORDER, VIDEO CAMERA OR AMPLIFIER.
OPTIONAL: ATTACHING THE RYCOTE WIND JAMMER AND TRIPOD MOUNT.
DISASSEMBLING 1. REMOVE THE FRONT CAP OF THE RYCOTE MICROPHONE HOLDER. 2. PULL OUT GENTLY AND REMOVE THE SCHOEPS CCM MICROPHONE OF THE CONNECTOR AND PLACE THE MICROPHONE IN IT’S PROTECTIVE CASE. 3. TAKE OUT THE FOAM WHILE KEEPING ONE HAND HOLDING THE BACK OF THE CABLE (SEE PHOTO 2 BELOW) ENABLING THE FOAM TO SLIDE OUT AND BE REMOVED WITHOUT FORCING THE CABLE AND CONNECTOR.
AFTER TAKING OUT THE FOAM 4. LOOSEN THE RYCOTE MICROPHONE HOLDER (PHOTO NEXT PAGE) FROM THE DISH BY HOLDING ONE HAND AROUND THE GRAY TUBE OF THE MOUNTING KIT BACK OF THE HANDLE AND USING THE OTHER HAND TO REMOVE RYCOTE MICROPHONE HOLDER.
5. REMOVE THE MOUNTING KIT FROM THE DISH. SYSTEM DISASSEMBLED.
FOLDING THE DISH AND PACKING IT IN THE SOFT CASE
FOR ADDITIONAL SUPPORT PLEASE CONTACT: Jon Strandberg, Telinga Microphones jon@telinga.com PH: +46 (0) 702 979 979 For more information regarding the SCHOEPS CCM microphone, specifications and EQ filter please visit www.schoeps.de/dish © 2019 TELINGA MICROPHONES, SWEDEN. www.telinga.
