Operation Manual
EN
"
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Malfunction : Possible causes / Solut ions :
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or there is
no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (see Start-up and use).
No w ater dr ains out from the
dishwasher.
• T h e di shwash e r cycle has n o t yet fi nished.
• The water outlet hose is bent (se e In stalla tio n ).
• T h e d rai n du ct i s b locked .
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a white film or
limes cale deposits.
• The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish tinge.
• The rinse aid dosage is too high.
The crockery has not been
dried properly.
• A wa sh cycl e w i th ou t a d ryi n g p rog ra mme ha s b e en se l e ct ed .
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid dispenser setting is not high enough.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any w ater in/Tap shut-off alarm .
(several short beeps are emitted)
(the ON/OFF indicator light f lashes and
the number 6 appears on the display).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when
the beeps sounded. Switch off the machine using the ON/OFF button, turn
on the tap and switch the machine back on after 20 seconds by pressing
the same button. Re-programme the machine and restart the wash cycle.
Wa te r in t ake s o le n o id va l ve
malfunction alarm
(the ON/OFF indicator light f lashes and
the number 2 appears on the display).
• Switch off the appliance by pressing the ON/OFF button and switch it back
on after one minute. If the alarm continues, shut off the water tap to
elim inate th e ri sk o f fl oo ding, re mo ve th e pl ug from th e electrical so cket
and contact Assistance.
Wate r inlet hose alarm
(the ON/OFF indicator light f lashes and
the number 1 appears on the display).
• Switch off the appliance by pressing the ON/OFF button.
Shut off the water tap to eliminate the risk of flooding, remove the plug
from the electrical socket and contact Assistance.
Water inle t hose alarm /Water
inlet filter blocked.
(the ON/OFF indicator light f lashes and
the number 7 appears on the display).
• Sw itch off the appliance by pressing the ON/OFF button. Shut off the
w ater tap to eliminate the risk of flooding and remove the plug from the
electrical socket. Make sure the w ater inlet filter has not become
blocked by various impurities. (see “ Care and maintenance” chapter).