INSTALLATION & OPERATING INSTRUCTIONS BMW E36 & E46 3 Series BMW E39 5 Series Quick Fit & Quick Fit Pro Harnessbelts Safety through Technology Edition 03/2007 Patents granted in Patente wurden erteilt in DE GB I USA 3 735 077 2 211 070 1 207 344 4 854 608 Installation and Operating Instructions Questions about Installation Package Contents Installation Operating Care and Maintenance Accessories and Spare Parts GEPRÜFT UND ÜBERWACHT TESTED AND INSPECTED 1 01 - 13 02 - 04 04 05 - 08 09 – 12 12 – 13
This manual contains important information as well as DANGERs, WARNINGs and SAFETY INSTRUCTIONs regarding the proper installation, effective use and maintenance of the SCHROTH harnessbelt. Please be sure to read and thoroughly understand its contents before beginning installation and before using the system. Follow all instructions and Safety Instructions carefully and be especially sure to heed all Dangers and Warnings.
4. Do you have a left belt for the driver’s side and/or a right belt for the passenger’s side? (See illustrations on page 5.) 1.
PACKAGE CONTENTS This SCHROTH asm harnessbelt is only suitable for adults on front outboard seating positions. The contents of each package is as detailed in the table below for each belt. BMW E36 Rallye 4 Right BMW E36 Rallye 4 Left PN#s 16620/16622 PN#s 16120 /16122 SCHROTH asm harnessbelts are not intended or suited for use by children under 12 years of age, or persons who weigh less than 88 lbs (40 kg) or those who are less than 4'11" tall (1.50 meters), regardless of age.
INSTALLATION INSTRUCTIONS 1 General Instructions Always leave original equipment seat belts in place and available for use. Use of improper attachment points will impair system performance. We strongly recommend that you leave in place all BMW factory provided 3-point restraint systems originally supplied for the front and rear seating positions of your vehicle when you install the SCHROTH asm harnessbelt. Removal of original equipment restraint systems may also violate applicable State or Federal law.
Pop off the black plastic cap to expose the retaining bolt. Using a T50 Torx head socket, back out the bolt. Place the SCHROTH connector just under the bolt head and reinstall the bolt. Before tightening the bolt, align the SCHROTH connector so that the webbing is pulling in the same direction that the belt will pass over your lap when connected. Torque the bolt to 30 ft.lbs. If desired, trim the plastic cover around the SCHROTH bracket and clip it back over the bolt.
3.4 Outside lap belt mounting points – E36 Sedan Unbolt the seat from the floor mounts. Move the seat all the way back and remove the front floor mounting nuts using a 16mm socket. Move the seat all the way forward and remove the rear mounting bolts. DO NOT REMOVE THE SEAT. Tip the seat in toward the front of the car to expose the BMW anchor bolt at the rear side of the seat-mount bracket.
5 Removal of E46 Rear Seatback Side Bolster If you can not get the bottom inside clip in place you can simply break it off (if it is not already broken). Do not worry about this as the bottom seat cushion holds the bottom of the bolster firmly in place. Push in the top of the side bolster to the upper mounting point. To reinstall the black plastic cap to the top of the bolster, you have to pop out a plastic pin from the top of the cap.
OPERATING INSTRUCTIONS 1 BMW E39 Sedan (Similar for E46 Sedan) Outside front mounting points. Schroth male lap belt connector is mounted so that it comes up to the inside of the factory belt. It is bolted using the same factory bolt. General instructions Most states require that all passengers wear seat belts when a car is in motion.
3 Adjustment of the seating position 6 How to adjust the belt Choose your most comfortable seating position for safe driving. 6.1 Lengthen the belt Hold the adjuster at right angles - 90° - to the belt and pull in direction of the arrow (see illustration beside). Driving and safety instructors recommend: "Select your seating position in the vehicle so that you can fully grip the upper edge of the steering wheel with your elbow still slightly bent and without moving your upper body from the seatback.
9 Improper fit of any lap belt can cause serious personal injury or death. • ALWAYS make sure that the lap belt is tightly adjusted. A lap belt in a harness or 3-point system that is too loose will impair the performance of the system. • The lap belt must fit tightly in the bend between the pelvic crest and the upper thigh! • Make sure belt is properly adjusted when a different person uses the belt or each time the seat is readjusted. (Heed WARNING on adjuster.
To use the Quick Fit Pro with a HANS® Device, be sure to make note of the following points: • • • • • • Install the belt as you would normally Place the HANS® device on your shoulders Carefully place the shoulder belts of the Quick Fit Pro over the yoke of the HANS® Be sure that the shoulder belt adjusters fall either entirely on or entirely off the yoke of the HANS®. If necessary, adjust the length of the tail strap to the correct length.
5 Installation Accessories Color key: black=0, blue=1, red=2, yellow=3, purple=5, green=8 The X in PINs must be substituted by the color key of the color you want to order! Shoulder belt pads, pair of • black with yellow flock printing Shoulder belt pads, pair of blue with black flock printing 01109 red, yellow, purple, green with black flock printing 0X109 One indication that the belt was exposed to excess strain and therefore requires replacement is when the stitches of the asm-system are ripped op