OWNER’S MANUAL Model 1000AP For 12-Volt Batteries SpeedCharge ™ computer smart amp amp 2 10 amp 6 S L O W CHARGE ™ F A S T CHARGE MEDIUM CHARGE Fully Automatic Microprocessor Controlled Battery Charger CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. ELECTRIC CORPORATION Mount Prospect, IL 60056 U.S.A.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................... 3 PERSONAL SAFETY PRECAUTIONS ...................................................................... 4 BEFORE USING YOUR BATTERY CHARGER ......................................................... 5 PLUGGING IT IN .................................................................................................. 5 USING AN EXTENSION CORD ..........................................................
IMPORTANT SAFETY INSTRUCTIONS WARNING – RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never set a battery on top of charger. Be sure to position the charger power cord to prevent it from being stepped on, tripped over, or damaged. Never place charger directly above battery being charged. The gases from the battery will corrode and damage the charger. Never pull out the plug by the cord when unplugging the charger. Pulling on the cord may cause damage to the cord or the plug. Never touch the battery clamps together when the charger is on. You could cause a spark.
BEFORE USING YOUR BATTERY CHARGER It is important to understand the charger’s requirements. This section explains the charger’s electrical requirements and how to prepare a battery for charging. extension cord, please make sure that you follow these guidelines: PLUGGING IT IN Your charger requires a 120V AC receptacle installed according to all local codes and ordinances. • Make sure that pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
OPERATING INSTRUCTIONS IMPORTANT: Follow all safety instructions and precautions when charging your battery. Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. CHARGING BATTERY IN THE VEHICLE: heavy, unpainted metal part of the chassis or engine block, away from the battery (see figure above). DO NOT connect clamp to negative battery post, carburetor, and fuel line or sheet metal part. 1.
5. Plug power cord into an AC outlet. The charger will be set to the 2 Amp for REGULAR battery type. CHARGING BATTERY REMOVED FROM THE VEHICLE: POSITIVE NEGATIVE 6. Press the appropriate control buttons to select the desired charge rate and battery type. The CHARGING (yellow) LED should light and the charging process should start. If the CHECK (red) LED is on, check for correct cable connections. BATTERY CHARGER BATTERY 24", 6 GAUGE CABLE POWER CORD TO GROUNDED POWER OUTLET 7.
SPEEDCHARGE CONTROL SpeedCharge ™ CHARGED 2A REGULAR 6A DEEP CYCLE 10A AGM, GEL CELL CHARGE RATE BATTERY TYPE CHARGING CHECK 1000AP CONTROL PANEL CHARGE RATE SWITCH Use this switch button to set the charge rate to one of the following three. • AGM, GEL CELL: AGM and gel cell batteries have sealed cases without vent caps. Such batteries are often smaller than the other types.
USING YOUR BATTERY CHARGER OVERVIEW Using the battery charger is very simple. First, connect the battery and AC power following the precautions listed under “OPERATING INSTRUCTIONS”. Then select the appropriate BATTERY TYPE and CHARGE RATE for your battery. The Charger will then do everything automatically. This section explains a few details. blinking the CHARGING LED. If successful, normal charging will resume after the battery is desulfated.
KNOW YOUR CHARGER Read this entire manual before using your charger. The items below are additional features of your charger. Fan: Your charger is equipped with a Relay: Your charger is equipped with a fan. It is normal for the fan to be on all relay. This device turns the charge the time. Keep the area near the charger current on and off to the battery. It is clear of obstructions to allow the fan to normal to occasionally hear a clicking operate efficiently. sound when the relay is turned on or off.
TROUBLESHOOTING Performance problems often can be corrected by the user. Please completely read this chart for possible solutions to common problems. PROBLEM POSSIBLE CAUSE SOLUTION Check RED light Is on. The battery is not connected correctly. Connect or adjust clips. Check for correct polarity. The battery is less than one volt. Replace the battery or try using a manual charger to bring above 1 volt. A button may have been pressed when the charger was plugged in.
LIMITED WARRANTY SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, ILLINOIS 60056-2179 MAKES THIS LIMITED WARRANTY TO THE ORIGINAL PURCHASER AT RETAIL OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE. Schumacher Electric Corporation warrants this battery charger for five years from date of purchase at retail against defective material or workmanship. If such should occur, the unit will be repaired or replaced at the option of the manufacturer.
