C - SERIES Height Adjustable Portable Goal Supports • C1000 • C2000 Installation & Owner’s Instructions Made in the USA
C1000 & C2000 Assembly Instructions This manual explains the proper installation, operation, and maintenance of your Schutt Sports goal. Study and understand these instructions thoroughly before installing, operating, or maintaining the goal. Failure to do so could result in serious injury or death and/or equipment damage. Consult your Schutt Sports dealer or Schutt Manufacturing, Co. if you do not understand the instructions in this manual or need additional information.
C1000 & C2000 Assembly Instructions TA B L E OF CONTENTS Warranty ........................................................................................................ 4 Contact Information...................................................................................... 4 Safety Instructions ....................................................................................... 5 Safety Decals ................................................................................................
C1000 & C2000 Assembly Instructions 2 YE A R W A R R A N T Y ON ENTIRE UNIT Schutt Sports Portable Goal Supports are thoroughly inspected at the factory. Schutt warrants, subject to the following limitations, the unit to be free from manufacturer defects in material or workmanship for the duration of ownership by the original retail purchaser. Original proof of purchase will be necessary to proceed with any warranty service.
C1000 & C2000 Assembly Instructions SAFETY INSTRUCTIONS Before operating or assembling / disassembling or providing maintenance on this product, read all safety precautions and warnings as found in the Installation and Owner’s Instructions. Failure to follow all instructions may result in serious injury or death and/or property damage. • Do not install or use this product unless the instructions within this manual have been carefully read and understood.
C1000 & C2000 Assembly Instructions SAFETY DECALS 800-426-9784 6 www.schuttsports.
C1000 & C2000 Assembly Instructions PLAYING COUR T CONSIDERATIONS Consider the following to determine where to place the basketball goal: • If court markings are to be used. • Backboard size and its extension distance from the pole. • Amount of playing surface desired beneath the goal. • Other functions of playing surface (such as driveway, tennis court, etc.
C1000 & C2000 Assembly Instructions Goal Specifications Model Backboard Size Height Range (A) C1000 32" x 48" acrylic C2000 32" x 48" acrylic Extension Distance (B) at: Playing Weight 6'-6" 8' 9' 10' 6'-6" to 10' 21" 28" 32" 36" 680 lbs 6'-6" to 10' 33" 40" 44" 49" 770 lbs C1000 (B) DO NOT HANG ON RIM DO NOT HANG ON RIM 10 0 96 90 86 80 (A) 76 70 66 16" 28" 800-426-9784 36" 8 42" www.schuttsports.
C1000 & C2000 Assembly Instructions C2000 Storage Configuration 56" 10 6 0 6 0 0 9 8 9 8 88" (B) DO NOT HANG ON RIM DO NOT HANG ON RIM 10 0 96 90 86 80 (A) 76 70 66 17" 32" www.schuttsports.
C1000 & C2000 Assembly Instructions GOAL ASSEMBLY IMPORTANT: Safe assembly of the goal requires two or three people in good physical condition and capable of lifting 80–100 lb (36–45 kg) each. IMPORTANT: Locate and familiarize yourself with all parts of the goal before beginning assembly.
C1000 & C2000 Assembly Instructions Unpacking - C1000 Fully loaded pallet weighs 352 lbs (160 kg) and is difficult to handle. To prevent serious injury, a suitable lifting device must be used to remove pallet from truck. Slider post is spring loaded and can extend rapidly. To prevent serious injury, do not cut strap that holds slider post in place or loosen lock handle (1) for height adjustment handle until instructed to do so. Step 1: Remove pallet from truck, and place it on a level surface.
C1000 & C2000 Assembly Instructions Base Assembly - C1000 Step 1: Push two brackets (1) down to raise brake feet and lower wheels. 1 Step 2: Remove four countersunk screws from lower padding. (Lower padding has six sides.) Step 3: Attach padding to underside of brackets using screws. NOTE: Operate brake feet and wheels as follows: • To lower brake feet and raise wheels, push up on padding until red lever latches.
C1000 & C2000 Assembly Instructions Unpacking - C2000 Fully loaded pallet weighs 440 lbs (200 kg) and is difficult to handle. To prevent serious injury, a suitable lifting device must be used to remove pallet from truck. Slider post is spring loaded and can extend rapidly. To prevent serious injury, do not cut strap that holds slider post in place or loosen lock handle (1) for height adjustment handle until instructed to do so. Step 1: Remove pallet from truck, and place it on a level surface.
C1000 & C2000 Assembly Instructions Base Assembly - C2000 Step 1: Push two brackets (1) down to raise brake feet and lower wheels. 1 Step 2: Remove four countersunk screws from lower padding. (Lower padding has six sides.) Step 3: Attach padding (2) to underside of brackets using screws. NOTE: Operate brake feet and wheels as follows: • To lower brake feet and raise wheels, push up on padding until red lever latches.
C1000 & C2000 Assembly Instructions Base Assembly - C2000 (continued) CAUTION: Without ballast material, unit is unstable and can tip easily. To prevent serious injury, do not proceed past next step until unit compartment is filled with ballast material. CAUTION: Unit is not designed for dunking in goal or hanging on goal. To prevent serious injury, do not overload unit with excessive ballast to permit improper goal use.
C1000 & C2000 Assembly Instructions Backboard, Rim, and Extension Post Assembly (continued) Step 4: Position extension post (1) 2 against backboard (2) rear and rim (3) against backboard front with slots in all parts aligned. 7 Step 5: Assemble with four 3/8" x 1" bolts (4), eight washers, and four nylock nuts. Verify that extension post, backboard, and rim are square with each other. Snug tighten nuts.
C1000 & C2000 Assembly Instructions Backboard Attachment Step 1: Lift backboard assembly (1) up and insert extension post (2) between slider post brackets (3). Align extension post rear holes with slider post bracket top rear holes. 4 5 6 1 Step 2: Insert 1/2" x 3-1/2" bolt (4) through holes and attach nut. Tighten nut and verify that backboard assembly pivots freely. Loosen nut as needed to allow pivot action.
C1000 & C2000 Assembly Instructions Upper Padding Attachment Step 1: Remove four screws and washers from upper rectangular shaped padding. 1 Step 2: With lower padding and red lever latched, so that brake feet are in down position and wheels are in up position, set upper padding on top of lower padding. Step 3: Attach upper padding (1) to post using four screws (2) and washers. Step 4: Adjust goal height. Refer to 2 Operation and Maintenance for instructions.
C1000 & C2000 Assembly Instructions Converting to Storage Position - C1000 CAUTION: Portable system can tip Step 4: Release red lever on back side easily if moved when goal is too high. To prevent serious injury, do not move portable system with goal above 6'-6" (2 m). of lower padding; pull out on padding, and rotate padding down completely to raise brake feet and lower wheels. Step 5: Move unit to storage location. Step 1: Fully lower goal.
C1000 & C2000 Assembly Instructions Cleaning • The exterior finish of the Schutt Sports goal is designed for many years of trouble-free operation and will not require any maintenance except for periodic cleaning. • An occasional coating of automotive paste wax will help extend the life of the paint and finish. IMPORTANT: Do not use abrasive cleaners to clean the goal—damage to the finish may result. • When cleaning is necessary, use water and a mild dish detergent; apply with a soft non-abrasive cloth.