INSTALLATION / OWNER’S MANUAL SERIES 4N/L51-J 4N/L62-J SERIES 44N/L5-J 44N/L6-J INFRA-RED POLE MOUNTED PATIO HEATER FOR YOUR SAFETY: FIELD CONVERTIBILITY: Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.
NOTICE: The Manufacturer. reserves the right to make changes to equipment and specifications without obligation or notification. This publication, or parts thereof, may not be reproduced in any form, without prior written consent from the manufacturer. Unauthorized use or distribution of this publication is strictly prohibited.
SERIES: 4N/L51-J, 4N/L62-J 44N/L5-J, 44N/L6-J INFRA-RED POLE MOUNTED PATIO HEATER INFRA-RED POLE MOUNTED PATIO HEATER TABLE OF CONTENTS TOPIC PAGE NUMBER 1. GENERAL ............................................ 1 2. INSTALLATION REQUIREMENTS ... 1 3. GAS SUPPLY ....................................... 1 3.1 4N51/62 SPECIFICATIONS ........... 2 3.2 4L51/62 SPECIFICATIONS ............ 3 4. MAIN COMPONENTS FOR ASSEMBLY ......................................... 4 5. ASSEMBLY INSTRUCTIONS ............. 5 6.
1. GENERAL These installation and operating instructions are intended for Series 4N51/62, 4L51/4L62 and 44N/L5, 44N/L6 Heaters. This appliance is an infrared fixed pole patio, deck and garden heater for operation with Natural Gas 4N51, 4N62 and 44N5, 44N6; and Propane 4L51,4L62 and 44L5, 44L6. The burner is controlled and adjusted by the gas control knob at the top of the heater, and the gas supply is fed up through the inside of the pole using flexible gas hose.
GAS REQUIREMENTS AND LEAK TESTING: NATURAL GAS: NEVER CONNECT AN UNREGULATED GAS SUPPLY TO THE HEATER. This heater requires a natural gas pressure regulator (not supplied) PRECAUTIONS: • • • • • • Periodically check the whole system for leaks or if the smell of gas is detected. Extinguish all open flames. Never smoke while leak testing. If you can not stop a leak, turn off the gas supply and call a qualified and licensed technician, or your gas supplier.
PROPANE: NEVER CONNECT AN UNREGULATED GAS SUPPLY TO THE HEATER. PRECAUTIONS: • • • • • • Periodically check the whole system for leaks or if the smell of gas is detected. Extinguish all open flames. Perform ALL leak testing outdoors. Never leak test while smoking. If you can not stop a leak, turn off the gas supply and call a qualified and licensed technician, or your gas supplier. Only those parts recommended by the Manufacturer should be used. Substitution will void the warranty.
4. MAIN COMPONENTS AND TOOLS REQUIRED FOR ASSEMBLY Tools Needed: (not supplied) Adjustable Wrench, Slip Joint Pliers, Phillips Screwdriver-Medium Blade (#2 or #3 blade), Hammer, 3/8” Masonry Drill Bit (if mounting on concrete patio), Teflon Plumbing Tape for Joints, Spray Bottle of Soapy Water or Paint Brush and soapy water (to check leaks) Parts Supplied: • • • • • • • • • • • • • • • • Main Burner / Head Assembly Unit 66” Flexible Gas Hose with brass fittings. 32” Aluminum Reflector (5 Piece).
5.
6. ASSEMBLY INSTRUCTIONS Using screws, place L-shaped stabilizers to bottom base. Secure with nut on inside of bottom base. Place base post on the bottom of the base in upward position. Secure using screws. Connect all center post sections together. Secure with screws.
ASSEMBLY..... CONTINUED Place hose through the opening on bottom base. Pull hose through upward inside center pole. Insert the gas hose provided, into the top of the pole feeding it down inside right to the bottom. Push the gas hose all the way down until it reaches the bottom, pulling it out through the side opening. Fit the 1” x 7” ribbed gas hose protection sleeve over the end of the gas hose connection and slide it all the way over the fitting onto the hose.
ASSEMBLY..... CONTINUED Connect hose to valve by turning tight. Secure entire top burner assembly to center post with screws that are already affixed to the burner assembly. 5 piece Sectional Reflector: Assemble the reflector pieces to the centre piece using the 12 1/4” washers and secure with M8-125 butterfly wing nuts.
ASSEMBLY..... CONTINUED Place a steel washer over each bolt on the burner top, before installing the Top Reflector. Position the assembled Reflector over the 3 bolts. Place a steel washer over each bolt on the burner top after installing the Top Reflector. Then secure with M8-125 butterfly wing nuts.
ASSEMBLY..... CONTINUED If placing on concrete patio only: Drill 3 holes 1 3/4” deep using the 3/8” masonry drill bit (not supplied). Insert the 3 x 3/8” lag bolts provided, tapping them in using the hammer shaft until the washer stops it at the floor. Tighten the nuts down tight and the stud threads will get longer. Remove the nuts and washers, leaving 3 x threaded studs sticking out of the concrete.
6. CONNECTION AND TESTING: NATURAL GAS CONNECTION: • • Connect the Natural Gas supply line to the flexible hose at the base of the pole as per gas code. A 5” w.c. Gas Pressure Regulator is required (not supplied) after the shut off valve to each heater or zone. PROPANE CONNECTION: • Connect the Propane Gas supply line to the flexible hose at the base of the pole as per gas code. • A 10” w.c. Gas Pressure Regulator is required (not supplied) after the shut off valve to each heater or zone.
7. A SAFE LOCATION FOR THE HEATER: Caution: The main application of this heater is to provide radiant heat comfort in the outdoors, at poolside, spa areas, terraces, patios and work areas, etc. It is necessary to provide “wind breakers”, against wind and breezes. When objects are left under a heater in operation, such objects will be subject to radiant heat and could be damaged. NOTE : This heater is approved for outdoor use only: • Respect minimum clearances to combustibles as shown in figure 12 below.
8. OPERATION AND LIGHTING INSTRUCTIONS: ‘AAA’ Battery Install ‘AAA” Battery into electronic igniter (as illustrated) by unscrewing cap counterclockwise, insert battery with positive terminal facing “in”. Replace cap. TO TURN ON: 1. From ‘OFF’ position, turn knob 90° counter-clockwise push and hold in. 2. Press the igniter until a flame is established. 3. Release the knob and check if the flame stays on. 4. If the flame goes out, repeat steps 1 & 2 above. 5.
9. TROUBLE SHOOTING WARNING: IMPROPER ADJUSTMENTS, BAD MAINTENANCE OR SERVICING PROCEDURES CAN CAUSE SEVERE PROPERTY DAMAGE THIS SECTION IS FOR, CERTIFIED AND LICENSED GAS TECHNICIANS ONLY PROBLEM Burner will not light PROBABLE CAUSE SOLUTION Gas valve may be in OFF position Turn the gas valve ON Pilot Orifice blocked Clean or replace orifice Air in supply system Purge air from lines. Open gas line valve & depress control knob for approx 2 mins. Loose connection Check igniter lead and fittings.
9.1 STORAGE When heater is not in use for a prolonged period of time verify that the gas valve is fully and tightly closed. To avoid damage, the reflector may be removed. 9.2 PREVENTATIVE CARE AND MAINTENANCE The burner area is likely to attract spiders, especially inside orifices. Once a year, the heater should be inspected for spider webs, insects, and debris around burners and orifices. Plugged injectors or orifices will obstruct the gas flow to the burner.
LIMITED WARRANTY CERTIFICATE FOR GAS-FIRED INFRA-RED PATIO HEATERS : 4001/2 (-J), 4N11/2 (-J) / 4401/2(-J), 44N1/2(-J) 4N/L51, 4N/L62 (-J) / 44N/L5, 44N/L6 (-J) SERIES The Manufacturer warrants that this product is free from defects in material or workmanship under normal use and service subject to the terms of this document.
