RANGEHOOD & INSTALLATION GUIDE DA-UM950S Revision V1 24/03/21 www.schweigen.com.
Index 1. Welcome Your State Regulatory Authority 3 3 2. Important Safety Information Before Installation Product Use Ducted or Recirculating? Electrical Cord 4 5 6 6 6 3. Description Rangehood Cutout Size 7 7 7 4. Operation Push Button Control Panel Speed Control 8 8 8 5. Cleaning & Maintenance Cleaning the Interior Cleaning the Exterior Filters Replacing the Lights 9 9 9 10 11 6.
1. Welcome Thank you for purchasing your new Schweigen rangehood. To get the maximum output from this unit, please read through this guide before use. The guide contains important information on the use and maintenance of the unit, as well as important safety notes. This will ensure your personal safety and the lasting value of your rangehood. Please always retain your proof of purchase to aid in any warranty queries.
2. Important Safety Information WARNING Please read this section thoroughly before attempting to operate the appliance. Inspect your product upon receipt. Any damage or defects MUST be reported within 48 hours, or no claim will be recognised. DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED. If this product is installed damaged, neither the supplier, nor the retailer, will be responsible for the costs associated with the repair, replacement, removal or re-installation of the appliances. 1.
2. Important Safety Information Before Installation 1. We recommend this appliance be installed or repaired by a qualified Schweigen Home Appliances technician. 2. Please see our website www.schweigen.com.au for recommended installers. 3. It is dangerous to modify any part of this appliance. Modification of any kind, will immediately void the warranty. 4. The manufacturer declines all responsibility in case of failure to adopt proper safety measures. 5.
2. Important Safety Information Product Use This product is designed for household use and should not be used for commercial applications. After use, always ensure that all controls are in the “OFF” position. When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire. (Flambé)w Electrical Cord Ensure the supply cord is not exposed to heat, chemicals or sharp objects. If the supply cord is damaged, it must be replaced by the manufacturer.
3. Description Rangehood 1. For use with Isodrive® motor system 3 1 2. Male plug (main power 240V) 2 3. Single 200mm outlet 4. Reducer (for Isodrive® 650 only) 5. Baffles 6. Lights 4 NOTE: Filter and light quantity may vary from model to model. 5 6 Cutout Size Use this as a guide only when designing your cabinet. We advise you to take the rangehood to your cabinet maker so they can tailor the cabinet to fit correctly. 833mm approx. 269mm approx. Dimensions may be subject to change.
4. Operation Schweigen silent rangehoods are recognised for their silent operation. Although this holds true for all of our rangehoods with external motors, one must note that the rangehoods are silent when they are used for regular cooking on the lower fan setting. Therefore, you will only hear the movement of air.
5. Cleaning & Maintenance Warning Always switch off and disconnect power before cleaning. Cleaning the Interior Clean the interior of the rangehood with a damp cloth and a neutral detergent or denatured alcohol. NOTE: Do not use denatured alcohol on the exterior of the rangehood. Do not clean the electric parts or the motor with liquids or solvents Cleaning the Exterior We recommended using a soft cloth, water and a liquid soap, rinsing it well and then drying it thoroughly.
5. Cleaning & Maintenance Baffles For this appliance to function effectively, regular maintenance is a must. • The function of the baffle is to collect the grease particles given off during cooking. • Clogged heavy oil deposits restrict airflow and may cause the motor to overheat and become a fire hazard. • Baffles should be cleaned every 3-6 weeks or after 40 hours of use. • For induction cooktop, please aim to clean them at least every 10 days, depending on use.
5. Cleaning & Maintenance Replacing the Lights Danger Always switch off and disconnect power before replacing the lights. Failure to do so may cause serious injury. Please be aware that the light bulb may retain heat for a short period of time after being switched off. Step 1 Step 2 Step 3 Remove the filters from the rangehood. Gently turn light bulb anticlockwise, pull the light bulb down and remove it from the light holder.
6. Installation Rangehood Size vs Cooktop Size In addition to the size, the height of the rangehood above the cooktop is important to obtain the best performance. INADEQUATE Rangehood smaller than cooking zone ADEQUATE Rangehood same size as cooking zone OPTIMAL Rangehood larger than cooking zone Overhead cabinet Rangehood Installation position It is important to consider the benchtop and overhead cabinetry depth before installing the rangehood.
6. Installation Mounting Instructions It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop. This will greatly improve its performance. Minimum height from the hob top surface to the underside face of the rangehood: • 600mm electric cooktop • 600mm gas cooktop Any installation above 800mm will compromise the extraction performance. Note: If the instructions for the gas cooktop specify a greater distance, this must be taken into account.
6. Installation Mounting Points for Body The diagrams below are a guide for all mounting points. SIDE VIEW FRONT VIEW Note: Please make sure all plastic protection on the rangehood and filters are removed before use. WARNING Please remove filters before installation. Failure to do so may damage the clips. DANGER Always switch off and disconnect the power supply before installing the rangehood. Failure to do so may cause serious injury.
6. Installation Installation Example FRONT VIEW BOTTOM VIEW Step 1 Insert mounting frame into cabinet. The support will only be needed in certain circumstances. NOTE: The mounting frame is not included. The requirement of a mountingSIDE frame VIEWis dependentSIDE VIEW on the type and location of installation. Please contact your installer for more information. Mounting frame TOP VIEW Step 2 Secure mounting frame to inside of cabinet. BOTTOM VIEW Step 3 Secure the undermount into cavity using screws.
6. Installation Ducting Please DO NOT crush or kink the ducting. 1. Crushed or kinked ducting creates sharp corners that creates turbulence. This reduces the size and efficiency of the ducting, lowers extraction and may cause excessive noise. 2. Sweeping curves and taut ducting reduces resistance and turbulence. The airflow and extraction will be more efficient and stronger.
6. Installation Isodrive® Motor Setup NOTE Please refer to the Isodrive® motor installation guide for more details on flexi ducting and Isodrive® motor installation.
6. _n_. Installation _LH Section_ System Overview 1. Isodrive® Motor 1 2. Roof Seal Kit (Dektite) (Not supplied)* 3. Support Straps (Not supplied)* 4. Attach Flexi Duct to Bell-Mouth Adaptor using ring clamp. Please DO NOT rip the ducting. 2 3 5. Isodrive® Motor Power Lead (Male Plug) 4 5 6. Rangehood to Isodrive® Motor Lead (Female Plug) 6 8 7 9 7. Main Power Lead (Male Plug, 10 Amp) 8. Flexi Ducting must be pulled taut. DO NOT crush or kink the ducting. 9.
7. Condensation _n_. _RH Information Section_ Cooking with Induction Cooktops Cooking with an induction or similar cooktop, may produce condensation on the rangehood. Unlike basic electric or gas cooking, induction cooktops heat food and liquid instantly, which in turn, produces vapours rapidly. Because of this rapid process, the rangehood filters do not have enough time to warm, which increases the chance of condensation forming.
Please make sure there is no obstruction in ducting or with the back draft fins. Check the outlet, make sure it is not blocked and you have the correct diameter ducting installed. X X X Rangehood does not direct air out (through chimney) X X Rangehood does not work X X Light does not work X Loud noise from the rangehood Page 20 X X X X Check the ducting has not come off the rangehood outlet or has been eaten through by rodents.
_n_. 8. Troubleshooting _RH Section_ Service Lodging an Online Service Request In the event that the failure is not due to the faults mentioned in the Troubleshooting section, you can lodge an online Service Request. To lodge an online Service Request, visit our website www.schweigen. com.au/service-and-warranty and click on the link and complete the service request form. A service request will require the following information: • The purchase date • The rangehood model and motor type (eg.
9. _n_. Specifications _LH Section_ Dimensions Front Back to wall 30 197 360 360 0 26 5 29 825 864 Technical Specifications Model DA-UM950S Feeding Voltage 220-240V 50Hz Lamp Power – Halogen (W) 2 x 35W (Optional) Lamp Power – LED (W) 2 x 3.
_n_.10. _RHDisclaimer Section_ Disclaimer Under our policy of continuous product development, product specifications may change without notice. Prospective purchasers should therefore check with the retailer to ensure this publication correctly describes the products being offered for sale.
Australia 8/3-4 Anzed Court, Mulgrave 3170 Victoria. Phone 1300 881 693 Email sales@schweigen.com.au Web www.schweigen.com.au New Zealand 5 Tolich Place, Henderson, Auckland 0610. Phone 0800 200 510 Email info.parex@emerson.com Web www.parex.co.
