RANGEHOOD & INSTALLATION GUIDE UM-PA9S (09.2017/v5.0) www.schweigen.com.
1. Welcome Thank you for purchasing this Schweigen appliance. To achieve the optimal performance from your appliance, and to avoid the risk of accident or damage, it is essential to read this manual before installation and first time use. This guide contains important information on the use and maintenance of the appliance, as well as important safety notes. Your appliance has been thoroughly checked for safety and functionality before being packaged and leaving the manufacturer.
Table of Contents 1. Welcome_____________________________________________________________________ 2 2. Important safety information____________________________________________________ 4 3. Description___________________________________________________________________ 7 4. Installation___________________________________________________________________ 8 5. Operation___________________________________________________________________ 15 6.
2. Important Safety Information Please read the instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual for future use or for subsequent owners. Check the appliance for damage after unpacking it. Do not connect or install the appliance if it has been damaged in transport. Any damage must be reported within 48 hours.
2. Important Safety Information Before Installation We recommend this appliance be installed or repaired by a qualified Schweigen Home Appliances technician. Please see our website www.schweigen.com.au for a list of our recommended installers. It is dangerous to modify any part of this appliance. Modification of any kind will immediately void the warranty. The manufacturer declines all responsibility in case of failure to adopt proper safety measures.
2. Important Safety Information Product Use The Rangehood has one mode of operation: Air extraction: The air is drawn in by the rangehood, filtered through the grease filters, and then expelled outside. Please check the cleaning and maintenance section for advice on the filter’s cleaning schedule. This product is designed for household use and must not be used for commercial applications. After use, always ensure that all controls are in the “OFF” position. Never flambé any food beneath the rangehood.
3. Description Rangehood 1 Female plug, to be connected to Isodrive1 motor system only 2 Male Plug, 2 to be connected to main power 240V 3 3 Single 200mm Outlet 4 Computer board* 5 Reducer (For Isodrive motor 650 only) 6 Filter 7 Cabinet door protection strip 8 Light 9 Rangehood mounting brackets 8 10 Instruction and screws pack 1 3 2 4 4 5 6 5 6 7 8 7 9 10 *IMPORTANT: The electronics MUST be accessible should a service be required by a qualified service technician.
4. Installation System Overview 1. Isodrive Motor 2. Roof Seal Kit (Dektite)* 3. Support Straps* 1 4. Attach Flexi Duct to Bell-Mouth Adaptor using cable tie or ring clamp. Please DO NOT rip the ducting. 2 5. Isodrive Motor Power Lead (Male Plug) 3 4 6. Rangehood to Isodrive Motor Lead (Female Plug) 5 7. Main Power Lead (Male Plug, 10 Amp) 6 8 7 9 8. Flexi Ducting must be pulled taut. DO NOT crush or kink the ducting. 9.
4. Installation DANGER Always switch off and disconnect main power before installing the rangehood. Failure to do so may cause serious injury. Mounting Laws and Regulations • The location of the installation must have permanent openings for ventilation. • Regulations concerning the expelling of air must be fulfilled. • It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop, this will greatly improve its performance.
4. Installation Overhead cabinet Rangehood Installation position It is important to consider the benchtop and overhead cabinetry depth before installing the rangehood. The information below is to be used as a guide only, drawings are not to scale and do not account for all circumstances. The cooktop is centrally installed in the benchtop in the diagrams below.
4. Installation Installation for UM-PA9S IMPORTANT Please read the installation guide thoroughly prior to installation. This model has a different method of installation compared to standard undermounts. Step 1 Fix the rangehood mounting supports (A) to the sides of the cabinet (B). Note: The brackets need to be levelled and secured, in order to hold the entire weight of the undermount. B A A Step 2 Slide the undermount in from the front of the cabinetry, onto the rangehood mounting supports (A).
4. Installation Step 3 Fit the undermount in place, using the installation screws provided (E). E Protecting the Cabinet Door — Optional A reversible “L” shaped profile is provided for optional cabinet door (D) protection. D “L” shaped profile Step 4 Only install the reducer if you are connecting the rangehood to the Isodrive 650 motor. DO NOT install the reducer for any other motor system.
4. Installation IMPORTANT Please ensure all plastic protection on the rangehood and filters is removed before use. Flexible Ducting Installation Please do not crush or kink flexi ducting, as it will reduce air flow and may cause noise to occur through the system. Ducting must be kept taut at all times. Isodrive Motor Setup NOTE Please refer to the Isodrive motor installation guide for more details on flexi ducting and Isodrive motor installation.
5. Operation Electronic Controls Model UM-PA9S. The rangehood has a 4-speed electronic keypad. Speed control usage suggestions: • Low speed for simmering. • Medium speed for light cooking. • High speeds for heavy frying or heavy cooking. To obtain the best performance, switch the rangehood on a few minutes prior to cooking and leave it running for at least 10 minutes after you have finished cooking. The buttons have the following functions: A B C D E A.
6. Cleaning and Maintenance WARNING Always switch off and disconnect power to the rangehood before cleaning. The manufacturer is exonerated from all responsibility in the event of fire due to poor maintenance of the filters and rangehood. Cleaning and user maintenance shall not be made by children without supervision. Filters • For this appliance to function effectively, regular maintenance is a must. • The function of the filter is to absorb the grease particles emitted during cooking.
6. Cleaning and Maintenance • For an induction cooktop, please aim to clean the filters at least every 10 days, depending on frequency of use. • The filters can be washed by hand or in the dishwasher Washing by hand - Immerse the filter in hot water and a suitable detergent, when clean, rinse with plenty of hot water. Dishwasher - Put the filter in the dishwasher and select a short program at low temperature. NOTE: The colour of the metal mesh filters may change after several washes.
6. Cleaning and Maintenance Replacing the Lights DANGER Always switch off and disconnect power before replacing the lights. Failure to do so may cause serious injury. Please be aware that the light bulb may retain heat for a short period of time after being switched off. 5 Type 4 (LED Strip TL): Replacing the Strip Lighting 1. Open the Perimeter Aspiration (P.A.) filter panel and gently loosen the screws. 2. Remove the glass perimeter chassis by removing the screws (A). 6 3.
7. Troubleshooting Cooking with Induction Cooktops Cooking with an induction or similar cooktop, may produce condensation on the rangehood. Unlike basic electric or gas cooking, induction cooktops heat food and liquid instantly, which in turn, produces vapours rapidly. Because of the accelerated process, the rangehood filters do not have enough time to warm up, which increases the chance of condensation forming.
Loud noise from the rangehood Rangehood does not work X Light does not work X X X Rangehood air exaction is weak X X Rangehood does not direct air out (through chimney) X X X X been eaten through by rodents. Check the ducting has not come off the rangehood outlet or has taut. installed correctly, eg. Length of ducting used, keep the ducting Check Isodrive installation manual, make sure the flexi ducting is correct diameter ducting installed.
7. Troubleshooting Calling the Technical Assistance Service Hotline In the event that the failure is not due to the faults mentioned in Trouble Shooting, contact Customer Service. In Australia, Customer Service 1300 829 066 In New Zealand, Customer Service 0800 200 510 Lodging an online Service Request In the event that failure is not due the reason/s in the trouble shooting section, you can lodge an online Service Request. To lodge a Service Request, visit our website www.schweigen.com.
8. Technical specifications 895 22 295 860 247 199 328 19.6 140 348 20.7 337.2 42 295 895 Model: UM-PA9S Feeding Voltage: 220-240V 50Hz Max Lamp Power: 1 x LED Strip 726mm long 3.
9. Disclaimer Under our policy of continuous product development, product specifications may change without notice. Prospective purchasers should therefore check with the retailer to ensure this publication correctly describes the products being offered for sale.
Notes Page 23
Australia 8/3-4 Anzed Court, Mulgrave 3170 Victoria. Phone 1300 881 693 Email sales@schweigen.com.au Web www.schweigen.com.au New Zealand 5 Tolich Place, Henderson, Auckland 0610. Phone 0800 200 510 Email info.parex@emerson.com Web www.parex.co.nz Distributed by Axis Group International Pty Ltd.
