22/123 Schwinn® Upright Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions e-mail from: Keith Weier date: 7/14/2005 page:1/16
FITNESS SAFEGUARDS AND WARNINGS Before starting any exercise program, consult with your physician or health professional. He or she can help establish the correct exercise frequency, intensity (target heart rate zone) and time appropriate for your particular age and condition. The following 3 warnings listed below are also located on the computer console mast of the exercise bike. Failure to follow any of these safeguards may result in injury or serious health problems.
• • • ensured if it is regularly examined and maintained. (See Maintenance section of the Owner’s Manual) Refer to the Maintenance section in the Owner’s Manual and disconnect power supply before servicing the bike. Replace Warning Label if damaged, illegible, or removed. We recommend that a minimum distance of 1 meter (39 inches) surrounding the bike is kept clear of all obstructions, including children, bystanders, and pets.
Parts List Check __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Quantity 1 1 1 4 1 4 4 1 1 4 1 1pr 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 4 1 1 e-mail from: Keith Weier Description Computer Handlebar Assembly Upper Heart Rate Cable Computer Mounting Screws Computer/Handlebar Mast Curved Washers Allen Bolt M8 x P1.
Hardware Chart Stage#4 24 Spring Washer 23 25 Bushing£ p 7 £1 p2* 15MM (1) Flat Washer 1 Stage#1 22 26 1 (1) Screwdriver 1 (Pedal Wrench) Screws M8xP1.25x16mm Stage#5 Allen Key Box Spanner 1 Screws M3x14mm Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.
122/123 Assembly Drawing with Reference Numbers e-mail from: Keith Weier date: 7/14/2005 page:6/16
Replacement Parts List Reference # Description 1 Computer 2 4 5 6 7 8 9 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 67 N/A N/A Handlebar Assembly Upper Heart Rate Cable Computer Mounting Screws Computer/Handlebar Mast Curved Washers Allen Bolt M8 x P1.
Each step of the assembly process has been broken down into 7 easy-to-follow stages. Please take just a few moments to read over these instructions to familiarize yourself with the process to make assembly quick and trouble-free. Assembly Stage #1 Attach Front and Rear Stabilizer Tubes to Main Unit Assembly hardware required: (4) Flat Head Screw 8x16L (item #11) 1.
Assembly hardware required: NONE 1. Attach right PEDAL (#13R) to the right crank arm on the RIGHT CRANK (#38R). Thread the pedal onto the crank arm and then tighten with pedal wrench. 2. Attach left PEDAL (#13L) to the left crank arm on the LEFT CRANK (#38L). Thread the pedal onto the crank arm and then tighten with pedal wrench. Note: There is a right pedal and a left pedal, marked by R and L. The threading on the left pedal is reversed from the right pedal.
Assembly Hardware Required: NONE 1. Insert SEAT POST (#17) into corresponding hole in MAIN UNIT (#14). Tighten down with SEAT POST ADJUSTMENT KNOB. (#16). 2. Insert SEAT (#21) onto SEAT SLIDER (#17). Tighten bolt on underside of the seat with a wrench until seat no longer twists or tilts. 3. Seat Adjustment: Adjust the seat height by unscrewing seat post adjustment knob and tightening into appropriate adjustment hole on the seat post. Leg should be almost fully extended at the bottom of the pedal stroke.
Assembly Stage #4 Attach Computer/Handlebar Mast to Main Unit. Attach Handlebar Assembly to Computer/Handlebar Mast.
1. Attach the LOWER COMPUTER CABLE (#10) from the MAIN UNIT (#14) to the UPPER COMPUTER CABLE (#9) from the bottom of the COMPUTER/HANDLEBAR MAST (#6). 2. Slide the COMPUTER/HANDLEBAR MAST (#6) onto the MAIN UNIT (#14). 3. Fasten the COMPUTER HANDLEBAR MAST to the MAIN UNIT with the 8mm BOLTS (#8) and CURVED WASHERS (#7) and tighten. 4.
Assembly Stage #5 Attach Handlebar Cover to Handlebar Assembly. Assembly Hardware Required: (4) Screws M3x14L (item#29) 1. Attach FRONT HANDLEBAR COVER (#27) and the REAR HANDLEBAR COVER (#28) around the HANDLEBAR ASSEMBLY (#2) using 4 SCREWS (#29).
Assembly Stage #6 Attach Computer Console to Computer/Handlebar Mast & Water Bottle Cage Assembly Hardware Needed: (4) Computer Screws (item #5) (Already attached to computer) (2) Screw 5x14L (item#19) 1. Attach UPPER COMPUTER CABLE (#9) exiting top of COMPUTER/HANDLEBAR MAST (#6) to the bottom of the COMPUTER (#1).
2. Place the COMPUTER (#1) on top of the COMPUTER/HANDLEBAR MAST (#6). The reading rack should wrap around the bottom of the computer console. 3. Attach the COMPUTER to the COMPUTER/HANDLEBAR MAST with the 4 COMPUTER MOUNTING SCREWS (#4). 4. Fasten WATER BOTTLE CAGE (#20) to COMPUTER SUPPORT TUBE (#6) with the two WATER BOTTLE SCREWS (#19) and tighten screws. 5. Insert WATER BOTTLE (#18) into WATER BOTTLE CAGE. 6.
Troubleshooting the Schwinn 122/123 Upright Exercise Bike TIP: Use assembly diagram(s) as reference when troubleshooting unit. PROBLEM: Computer will not start, function, or is blank… (SOLUTION): 1. Ensure the batteries were installed correctly. 2. Check the wiring connections and connector orientation made to the computer. 3. Confirm that wiring (cable assembly) has not been damaged 4. If computer still fails to start please call 1.800.864.1270 for assistance.
