Do not print this page
©2006. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr.
Upright bike Assembly guide PN 001-6894 Rev C (031308) Assembly Guide
CONTENTS Table of Contents Hardware ................................................................................................ 2 Exploded View......................................................................................... 3 Parts List . ................................................................................................ 4 Assembly Instructions .......................................................................... 5 Important Contact Numbers ..................................
Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact Schwinn at 1.800.864.
EXPLODED VIEW EXPLODED VIEW / ! ! ! / / " / " / / / # / ' # # # ' # ' & & & & + 2 $ / + , 0 % 3
PARTS LIST PARTS LIST 4 Ref. Description Qty A A-1 A-2 B B-4 C C-1 C-2 C-3 C-4 D E F-1 F-3 F-4 F-7 G G-1 G-8 K O O-1 O-2 O-3 O-4 O-5 O-6 O-7 0-8 P Computer Screw M5x14L Computer bracket Handlebar Heartrate wire Handlebar mast Upper computer wire Bottle cage Screw M5x20L Bottle cage holder Front stabilizer Rear stabilizer Washer 8x19x2 Lower computer wire Screw M8xP1.
ASSEMBLY INSTRUCTIONS Basic Assembly Principles Here are a few basic tips that will aid in the assembly process . By using these principles, you can simplify each process and save yourself extra time and effort. 1. To make the assembly process go faster, gather the pieces you need for each step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2.
ASSEMBLY INSTRUCTIONS Step 1 Install Front and Rear Stabilizers Parts: • Front Stabilizer (Ref. D ) • Rear Stabilizer (Ref. E ) Tools: • Supplied Allen Wrench 1-1 Attach the Rear Stabilizer (E) to the rear of the Main Unit using two M8 X 16mm screws (O-4). 1-2 Attach the Front Stabilizer (D) with the UP sticker and wheels toward the front of the Main Unit using two M8 X 16mm screws.
ASSEMBLY INSTRUCTIONS Step 2 Install Pedals Parts: • Right Pedal (K-R) • Right Pedal (K-L) Tools: • Supplied Pedal Wrench 2-1 Screw the Left Pedal ( has an “L” stamped into the end of the pedal ) into the Left Crank Arm. Note: The Left Pedal has a left handed thread and screws in counter clockwise. 2-2 Screw the Right Pedal ( has an “R “stamped into the end of the pedal ) into the Right Crank Arm.
ASSEMBLY INSTRUCTIONS Step 3 Install Seat Post Parts: • Seat post (Ref. G) 3-1 Completely unscrew the Seat Post Adjustment Knob (F-7) from the main unit and insert the Seat Post (G) into the hole. Re-install the Adjustment Knob by screwing in firmly into place.
ASSEMBLY INSTRUCTIONS Step 4 Install Seat Parts: • Seat (Ref. G-8) Tools: • Supplied Wrench 4-1 Position the Seat (G-8) on the top of the Seat Slider. Tilt the the Seat to desired angle and tighten the two nuts on the underside of the Seat until completely tight. Seat Adjustment: To adjust the Seat Post height, unscrew the Adjustment Knob about one full turn and pull outward on the knob. Slide the Seat Post to desired postition.
ASSEMBLY INSTRUCTIONS Step 5 Install Handlebar Mast Parts: • Handlebar Mast (Ref C) Tools: • Supplied Allen Wrench 5-1 Remove the four Allen Bolts (F-4) and Curved Washers (F-1) from the frame . 5-2 Connect the Upper and Lower Computer Wires. (Detail A) 5-3 Insert the Handlebar Mast (C) into the main unit. 5-4 Re-install the four Allen Bolts and Curved Washers and completely tighten.
ASSEMBLY INSTRUCTIONS Step 6 Install Handlebar Parts: • Handlebar (Ref B) • Console Slider Adjust Knob (Ref 0-5) • Washer (Ref 0-6) • “T” Nut (Ref 0-8) 6-1 Tuck the Computer Wires into the Mast to allow insertion of the Handlebar . 6-2 Slide the Handlebar (B) into the Mast, insert the “T” nut (0-8) and secure with the Console Slide Adjust Knob (0-5) and Washer (0-6) . (Figure A) 6-3 Pull the Computer Wires back up through the Handlebar as shown.
ASSEMBLY INSTRUCTIONS Step 7 Install Computer Bracket Parts: • Computer Bracket (Ref. A-2) • Angle Adjust Knob (Ref. O) • Carriage Bolt (Ref. O-7) • Screw M8x85 (Ref. O-1) • 2 Washers (Ref. O-3) • Hex Nut (Ref. 0-2) Tools: • Supplied Socket and Flat Wrenches 7-1 Align the Computer Bracket (A-2) with the holes in the Mast. (See assembled view for reference) 7-2 Install and completely tighten the hardware. Note: Use the Angle Adjust Knob to position the Computer to fit individual preferences.
Parts: • Computer (Ref. A ) Tools: • Supplied Phillips Head Screwdriver 8-1 Remove the four screws from the back of the Computer. 8-2 Connect the Computer Wire and Heartrate Wire to the connectors on the back of the Computer as shown. 8-3 Align the Computer with the holes in the Computer Bracket. (A-2) 8-4 Install and completely tighten the hardware.
ASSEMBLY INSTRUCTIONS Step 9 Install Bottle Cage Parts: • Bottle Cage A (Ref. C-2 ) • Bottle Cage B (Ref. C-4 ) Tools: • Supplied Phillips Head Screwdriver 9-1 Remove the two M5 x 20L (Ref. C-3) screws from the Mast. 9-2 Align Bottle Cage A and B with the holes in the mast as shown. (see assembled view for reference) 9-3 Install and completely tighten the hardware. C-4 C-2 Ref.
ASSEMBLY INSTRUCTIONS Step 10 Plug in AC Adapter Parts: • AC Adapter (Ref. P) 10-1 Plug the AC Adapter (P) into the recepticle on the rear left of the unit and into a 110 volt outlet.
ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner’s Manual for information regarding computer operation, product maintenance, Warranty information, and general fitness and exercise guidelines.
IMPORTANT CONTACT NUMBERS IMPORTANT CONTACT NUMBERS If you need assistance, please have both the serial number of your machine and the date of purchase available when you contact the appropriate Nautilus office listed below. OFFICES IN THE UNITED STATES: E-mail: cstech@nautilus.com • NAUTILUS INNOVATION CENTER Nautilus, Inc. 1886 Prairie Way Louisville, Colorado, USA 80027 Phone: 800-NAUTILUS (800-6288458) Fax: 800-898-9410 • TECHNICAL/CUSTOMER SERVICE Nautilus, Inc.