206 Schwinn® Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions 206 Recumbent Exercise Bike
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, please read the following precautions before using the Schwinn 206. 1. It is the responsibility of the owner to ensure that all users of this equipment are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature and follow them carefully before using the equipment. 3. If you feel pain or dizziness at any time while exercising, stop immediately and consult your physician. 4.
206 Schwinn Recumbent Bike Parts List, Hardware Chart, and Assembly Instructions Assembly of the 206 Recumbent Bike is divided into 5 easy stages; each comprised of only a few setup steps. Before proceeding with the assembly, please read over the easy to follow instructions to familiarize yourself with the process. • A flat area of 5’ x 7’ is suggested to assemble the 206 exercise bike.
Parts List Check __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Quantity 8 15 1 1 1 1 8 1 1 1 1 1 1 2 2 2 1 1pr 8 4 1pr 19 2 2 1 1 1 1 1 1 1 1 4 1 1 2 1 1 Description Reference # Allen Bolt M8 x P1.
Hardware Chart Stage#1 Stage#2 Allen Bolt M8xP1.25x16mm Allen Bolt M8xP1.25x Allen Bolt M8xP1.25x16mm Flat Washer for ф 8* ф 16* 2T Flat Washerф 8* ф 19* 2T mm Flat Washerф 8*ф 19*2T Flat Washer Stage#3 Acorn Nut M8 Curved Washer Carriage Bolt M8xP1.25x75mm Stage#5 Stage#4 Curved Washer Carriage Bolt M8xP1.25x mm Allen Bolt M8xP1.25x16mm Allen Bolt M8xP1.
206 Assembly Drawing with Reference Numbers 34 33 57 56 30 28 29 27 58 22 19 26 25 21 3 31 8 16 17 18 19 20 23 22 2 12 13 14 15 22 32 20 19 47 9 11 2 22 10 24
Replacement Parts List Reference # 3 4 5 6 9 10 11 12 13 14 15 16 17 20 21 22 23 24 25 26 27 28 29 30 32 33 34 56 57 Description Seat Pin Adjustment Knob Seat Seat Back Handlebar Assembly Seat Rail Rear Stabilizer Tube Seat Rail End Cap Buffer Buffer Plate Flat Washer Screws Carriage Bolt M8 x P1.25 x 75mm Front Stabilizer Tube (w/wheels) Acorn Nut Pedals (Left & Right) Allen Bolt M8 x P1.25 x 16mm Bolt Cover Carriage Bolt M8 x P1.
Instructions IMPORTANT!: To ensure ease of assembly please verify the size and quantity of all the required assembly hardware and parts with the enclosed parts list and full size hardware chart. Each step of the assembly process has been broken down into 5 easy-to-follow stages. Please take just a few moments to read over these instructions to familiarize yourself with the process to make assembly quick and trouble-free.
Step 3: Attach SEAT BACK (#5) to SEAT FRAME (#8) with 4 ALLEN BOLTS (#1) and 4 WASHERS (#2). Tighten Bolts.
Assembly Stage #2 Attach Rear Stabilizer and Seat Rail to Seat Assembly . Assembly hardware required: (4) M8 Allen Bolts 16mm (item #22) (4) Flat Washers Ø8 * Ø19 * 2T(item#2) Step 4: Attach SEAT RAIL (#9) to REAR STABILIZER TUBE (#10) with 4 FLAT WASHERS (#2) and 4 ALLEN BOLTS (#22). Tighten bolts. Step 5: Place END CAP (#11) on the end of the SEAT RAIL (#9). Make sure the HR CABLE (#47) is strung through the exit slot on the SEAT RAIL before end cap is secured.
Assembly Stage #3 Attach Front Stabilizer Tube and Pedals to Main Unit Assembly Hardware Required: (2) M8 Bolt 75mm long (item #16) (2) Curved Washers (item #19) (2) Acorn Nut (item #20) Step 8: Attach FRONT STABILIZER TUBE (#17) to the MAIN UNIT (#31) with the M8 BOLT 75mm (#16), CURVED WASHER (#19), and ACORN NUT (#20). Tighten Bolts with provided wrench. Step 9: Attach RIGHT PEDAL (#21) to the right crank arm on the MAIN UNIT (#31).
Assembly Stage #4 Attach Seat Rail and Lower Base Frame to Main Unit 9 31 Assembly Hardware Required: (7) Allen Bolts 16 mm long (item #22) (3) Flat Washers (item #2) (2) Allen Bolts 90 mm long (item #24) (2) Curved Washers (item #19) (4) Flat Washer (item #7) Step 10: Slide the LOWER BASE FRAME (#32) into the MAIN UNIT (#31), attach with 3, 16mm BOLTS (#22) and 3 FLAT WASHERS (#2). Do not completely tighten until after step 12.
- IMPORTANT - Before proceeding to step 11 please complete the following steps. Failure to do so could lead to damage to the handgrip heart rate wires! 1) Remove END CAP (#11) from the end of the seat rail. The coiled wire seen above the seat rail needs to be re-routed out the back of the seat rail . 2) Pull the wire from the back of the seat rail until the male prong is flush with the front of the seat rail. Connect the cables from MAIN UNIT and Seat Rail.
Assembly Stage #5 Attach Console Mast to Main Unit 31 15 EP ST 34 33 30 28 29 ST E P1 3 14 EP T S 57 56 27 26 25 22 19 58 31 31 Step 16 Assembly Hardware Required: (4) Allen Bolts 16 mm long (item #22) (4) Curved Washers (item #19) (4) Computer Screws (item #33) (2) Water Bottle Cage Screws M5*12 mm (item #56) Step 13: Run CONSOLE MAST (#30) through the CONSOLE MAST COVER (#27) and onto the MAIN UNIT (#31).
Step 15: Attach UPPER COMPUTER CABLE (#28) and HR CABLE (#29) to under side of COMPUTER (#34). Place COMPUTER (#34) on top of CONSOLE MAST (#30), the reading rack should wrap around the bottom of the COMPUTER. Attach COMPUTER to CONSOLE MAST with COMPUTER MOUNTING SCREWS (#33). (In computer back) Tighten with Phillips head screwdriver. Step 16: Plug power adapter into the wall and into the recumbent bike.
Troubleshooting the Schwinn 206 Recumbent Exercise Bike TIP: Use assembly diagram(s) as reference when troubleshooting unit. PROBLEM: Computer will not start, function, or is blank… (SOLUTION): 1. Ensure the unit is plugged into a 110v outlet. 2. Check the wiring connections and connector orientation made to the computer. 3. Confirm that wiring (cable assembly) has not been damaged 4. If computer still fails to start please call 1-800-4-MYHOME for assistance.