MS-(H)-S Analog (Hotplate) Magnetic Stirrer User Manual MS-H-S Analog Hotplate Magnetic Stirrer MS-S Analog Magnetic Stirrer Please read the User Manual and the related Video of this instrument on our website carefully before use, and follow all operating and safety instructions! The website www.scilogex.com Cat No.
Contents Contents Preface Service Warranty 1 Safety Instructions 2 Proper use 3 Inspection 3.1 Receiving Inspection 3.
MS-(H)-S Analog (Hotplate) Magnetic Stirrer Welcome to the “MS-(H)-S Analog Hotplate Magnetic Stirrer User Manual”. Users should read this Manual carefully, follow the instructions and procedures, and beware of all the cautions when using this instrument. Please provide the customer care representative with the following information: • Serial Number(on the rear panel) • Description of problem (i.e.
MS-(H)-S 1 Analog (Hotplate) Magnetic Stirrer substances or under water. • Gradually increase the speed, reduce the speed if : - The stirring bar breakaway because of too high speed - The instrument is not running smoothly, or if the container moves on the base plate. • Temperature must always be set to at least 25 ℃ lower than the fire point of the media used.
MS-(H)-S Analog (Hotplate) Magnetic Stirrer • The instrument may only be opened by experts. • Keep away from high magnetic field. • Observe the minimum distances between the devices, between the instruments and the wall and above the assembly (min. 100 mm). 2 Proper use The instrument is designed for schools, laboratories or factories. This device is not suitable for use in residential areas or other areas that may cause danger to the user or instrument as mentioned in Chapter 1.
MS-(H)-S Stirrer bar User manual Analog (Hotplate) Magnetic Stirrer 5 Control and Display 1 1 Table 1 4 LED Stir Trial run LED Heat • Make sure the required operating voltage and power supply voltage match. • Ensure the socket must be earthed. • Ensure the power be off and the speed control knob and the temperature control knob to the lowest position • Plug in the power cable and power on the device. • Add the medium into the vessel with a stirring bar. • Put the vessel on the plate.
MS-(H)-S Analog (Hotplate) Magnetic Stirrer Items Descriptions Stir knob Set the rated rotary speed in the safe stirring range from 0 to 1500 rpm. The function “Stirring” is switched ON or OFF via the knob Heat knob (MS-H-S) Note: Forbid to transfer the vessel when the instrument working,or you must restart Stir function again, avoiding Stirring bar breakaway. Set the rated temperature in the safe temperature range from room temperature to 340 ℃.
MS-(H)-S cleaning. • Unplug the power line when cleaning. • Only use cleanser that we advised as below: Dyes Isopropyl alcohol Construction materials Water containing tenside / isopropyl alcohol Cosmetics Water containing tenside / isopropyl alcohol Foodstuffs Water containing tenside Fuels Water containing tenside Analog (Hotplate) Magnetic Stirrer 9 Associated standards and regulations Construction in accordance with the following safety standards: EN 61010-1 UL 3101-1 CAN/CSA C22.
MS-(H)-S Analog (Hotplate) Magnetic Stirrer Max. magnetic bar [mm] 80 Motor type External rotor brushless motor Max. power input of motor [W] 18 11 Max.
MS-(H)-S Analog (Hotplate) Magnetic Stirrer 811111019999 MS-S without Heating,Stainless Seel, Cn plug 110V/220V/50Hz/60Hz 12500005 Stirring bars(30mm x 6mm),1pcs/pk Stirring bars(30mm x 6mm),1pcs/pk 811111029999 MS-S without Heating ,Stainless Seel, Euro plug 110V/220V/50Hz/60Hz 12500005 18900011 Stirring bars(40mm x 8mm),1pcs/pk 12500004 Stirring bars(50mm x 8mm),1pcs/pk 811111039999 MS-S without Heating,Stainless Seel, UK plug 110V/220V/50Hz/60Hz 18900013 Stirring bars(65mm x 8mm),1pcs/pk
SCILOGEX, LLC 500 Four Rod Road Suite 122 Berlin, CT 06037 USA Tel:1- (860) 828-5614 Fax:1- (860) 828-5389 E-mail: info@scilogex.com Website:Http://www.scilogex.