Document # 2064 (TMS) 9/26/03 SCION xA 2004 − SECURITY WITH RKE (V3) Section I − Installation Preparation Part Number: 08586−52970 Section I − Installation Preparation Kit Contents Item # 1 2 3 4 5 6 Quantity Reqd. 1 1 2 1 1 1 Description Wire Harness V3 Security ECU Remote Control Transmitters Piezo Buzzer Status Monitor Butyl Tape Special Chemicals 3MTM Prep Solvent−70 Household Win dex Cleaning Fluid Glass Cleaner General Applicability Note: SCION xA with power door locks, only.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure Section II − Installation Procedure STOP Socket (10 mm), Ratchet NOTES: Removed Parts:− Place all removed parts on a protected surface. STOP Connectors:− When disconnecting connectors, do not pull on the wires; pull on the connectors. STOP Wire Ties:− When using wire ties to secure harness, clip the wire ties after securing them. Negative Battery Cable Fig. A−1 A. Vehicle Disassembly Panel Removal Tool Float Clip 1.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 6. Remove the two screws securing the lower steering column cover behind the steering wheel. (Fig. A−5) i. Phillips Screwdriver Insert the key into the ignition switch and turn it to ON to unlock the steering wheel. ii. Turn the steering wheel left and right to gain access to the screws. Screw 7. Remove the lower steering column cover. (Fig. A−6) i. Remove the bottom screw securing the cover. Screw Fig.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 10. Remove the center cluster under cover. (Fig. A−9) i Panel Removal Tool Remove the two clips securing the under cover. Clip 11. Using the Nylon Panel Removal Tool, remove the passenger’s side step cover. (Fig. A−10) STOP STOP i. Clip Cover the floor and seats before starting. Under Cover Fig. A−9 ii. Remove the float clip first to prevent damaging the panel. Panel Remover Tool 12.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure B. Piezo Buzzer Installation Side Cutter 1. Using one large foam tape and one large wire tie, secure the Piezo Buzzer to the vehicle’s harness near the vehicle’s clip. (Fig. B−1) STOP i. Piezo Buzzer Large Foam Tape Do not cover the opening of the Buzzer with the foam tape. ii. Ensure Buzzer opening is facing downwards. STOP 2. Locate the gray 2P connector near the vehicle grommet. (Fig. B−2) i. Fig.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure C. V3 Harness Installation Small Flat Blade Screwdriver 1. Locate the vehicle harness’ white 3P diode connector and remove the tape securing the white 3P diode connector to the driver’s side cowl area. (Fig. C−1) 2. Locate and disconnect the white 13P and 14P connectors from the driver’s side cowl area. (Fig. C−1) 3. Using a small flat blade screwdriver, remove the diode from the white 3P diode connector. (Fig. C−1) STOP i.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 7. Disconnect the empty 1P female connector plugged into the V3 harness’ 1P male connector. (Fig. C−4) 8. Using a small flat blade screwdriver, lift up the terminal retainer on the back of the empty 1P connector. (Fig. C−4) Small Flat Blade Screwdriver 1P (Female) Retainer 9. Insert the terminal at the end of the vehicle harness’ RED wire into the empty 1P connector. (Fig. C−5) STOP STOP i. ii.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 13. Secure the vehicle harness’ white 3P diode connector and V3 Harness’ white 1P connector to the vehicle harness using one medium wire tie. (Fig. C−7) 14. Secure the 13P connectors and V3 harness to the connector box with one large wire tie. (Fig. C−7) i. Arrange and secure the 13P connectors under the connector box as shown. 15. Secure the V3 harness to the vehicle harness with one medium wire tie. (Fig. C 7) 16.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 18. Plug in the V3 harness’ white 9P connectors between the driver’s side J/B and the vehicle harness 9P connector. (Fig. C−10) i. 13P (White) 9P (White) J/B Verify the connectors are plugged in securely. 19. Plug in the V3 harness’ white 13P connectors between the driver’s side J/B and the vehicle harness 13P connector. (Fig. C−10) i. Side Cutter V3 Harness Back Side View Verify the connectors are plugged in securely.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 23. Plug in the V3 harness’ white 6P connectors between the vehicle harness white 6P connector and the lower part of steering wheel. (Fig. C−12) i. Side Cutter Medium Wire Tie Large Wire Tie Verify the connectors are plugged in securely. 6P (White) 24. Secure the 6P connectors and V3 harness to the vehicle harness with one large wire tie. (Fig. C−12) 25. Secure the V3 harness to the vehicle harness with one medium wire tie.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 30. Route and secure the V3 harness to the vehicle harness with one medium wire tie below the steering column. (Fig. C−15) Side Cutter 31. Route and secure the V3 harness with the black 4P connector to the vehicle harness with two medium wire ties to the left of the steering column. (Fig. C−16) i. V3 Harness Ensure that these wire ties do NOT secure the fog light switch harness. D. Status Monitor Installation 1.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure E. Wire Harness Installation (Continued) Large Foam Tape 1. Locate the vehicle’s brace in the driver’s side behind the center cluster. Attach one large foam tape to the brace. (Fig. E−1) i. Verify the edge of the brace is covered. 2. Locate the vehicle’s brace in the driver’s side behind the center cluster. Attach one large foam tape to the brace. (Fig. E−2) i. Vehicle’s Brace Attach tape to both ends of the bracket. ii.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 4. Route and secure the V3 harness to the vehicle’s bracket with one medium wire tie behind the center cluster. (Fig. E−4) i. Side Cutter Pass the wire tie through the hole of the vehicle’s bracket. 5. Route and secure the V3 harness to the vehicle harness with one medium wire tie in the glove area. (Fig. E−5) 6.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 7. Plug in the V3 harness’ white 1P connector to the vehicle harness’ white 1P connector. (Fig. E−7) i. Side Cutter Verify the connectors are plugged in securely. 1P (White) 8. Secure the 1P connectors to the vehicle harness with one medium wire tie. (Fig. E−7) 9. Secure the V3 harness to the vehicle harness with two medium wire ties. (Fig. E−7) 10.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 13. Plug in the V3 harness’ white 12P connectors between the vehicle harness white 12P connector and the passenger side cowl area. (Fig. E−10) i. Side Cutter V3 Harness Verify the connectors are plugged in securely. Medium Wire Tie 14. Secure the 12P connectors to the vehicle harness with one medium wire tie. (Fig. E−10) F. V3 ECU Preparation and Installation 1. Turn the adjustment screw on the V3 ECU to the 6 position.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 3. Apply two large foam tapes to the V3 ECU as shown. (Fig. F−3) Large Foam Tape 4. Locate and remove the bolt securing the air− conditioner unit in the glove box area. (Fig. F−4) STOP i. V3 ECU Do not discard the bolt. 5. Apply the butyl tape to the air−conditioner unit as shown. (Fig. F−4) 6. Connect the V3 ECU connectors (8P, 12P, 22P) to the V3 ECU. (Fig. F−5) i. Verify the connectors are plugged in securely.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure 7. Mount the V3 ECU to the glove box area with the vehicle’s bolt. (Fig. F−6) i. 10mm Socket Verify the bolt is tightened securely. ii Verify the V3 harness does not droop downward. 8. Using a small strip of foam tape, secure the GRAY Antenna wire to the inside surface of the upper dash cover as shown. (Fig. F−7) V3 ECU G. Warning Label Installation 1.
SCION xA 2004 − SECURITY WITH RKE (V3) Section II − Installation Procedure H. Completing the Installation Socket (10 mm) Torque Wrench 1. Complete the reassembly of the vehicle. i. 45 deg. Reconnect any disconnected connectors. ii. Verify the panels fit together properly with no uneven gaps between them. 2. Clean up and remove any trash. 3. Reconnect the vehicle’s negative battery cable. (Fig. H−1) i. Position the negative terminal to the battery as shown (~45 deg.). Negative Battery Cable Fig.
SCION xA 2004 − SECURITY WITH RKE (V3) Section III − Functional Verifications Section III − Functional Verifications Check: Look For: Accessory Function Checks Press and release the remote control s lock 1. The tail and marker lights flash once. button to start the system s arming process. The buzzer chirps once. All doors lock. The Status Monitor s LED lights up. 2. After 30 seconds, the LED starts flashing; Wait 30 seconds. the system is now armed. 3. The tail and marker lights flash twice.
SCION xA 2004 − SECURITY WITH RKE (V3) Section III − Functional Verifications Section III − Functional Verifications Check: Look For: Press and release the remote control s panic 9. The horn sounds repeatedly. button to trigger the panic alarm. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up. Press and release the remote control s panic 10. The horn stops sounding. All the lights stop flashing and/ or turn off.
SCION xA 2004 − SECURITY WITH RKE (V3) Section III − Functional Verifications Section III − Functional Verifications Check: Look For: Manually unlock the driver s door again and 16. The driver s door lock attempts to lock hold it unlocked, open the door, then sit in repeatedly. the driver s seat. The horn continues to sound repeatedly. The interior lights remain on. The headlights, tail lights and marker lights continue flashing. The LED remains on.
SCION xA 2004 − SECURITY WITH RKE (V3) Section III − Functional Verifications Section III − Functional Verifications Check: Look For: Press and release the remote control s 21. The horn stops sounding. unlock button to stop the alarm. All the lights stop flashing and/ or turn off. The Status Monitor s LEDturns off. Press and release the remote control s lock 22. Refer to step number 1 and number 2. button to start the system s arming process, then wait 30 seconds until the system is armed.
SCION xA 2004 − SECURITY WITH RKE (V3) Section III − Functional Verifications Section III − Functional Verifications Check: Look For: NOTE: Adjust as necessary by increasing the GBS setting to the next level if the alarm does not trigger during the functional verifications. NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration. Insert the key into the driver s door key 28. The horn stops sounding.
