SCION tC 2007 - SECURITY (V5) Preparation NOTE: Part number of this accessory may not be the same as the part number shown. Part Number: PT398-21070 Kit Contents Item # 1 2 Quantity Reqd. 1 1 Description V5 Harness GBS ECU Quantity Reqd.
SCION tC 2007 - SECURITY (V5) Procedure Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.).
SCION tC 2007 - SECURITY (V5) Procedure (e) Remove the fuse box cover. (Fig. 1-4) Fuse Box Cover (1) Take care not to damage the two upper tabs. Fig. 1-4 (f) Remove the cluster panel. (Fig. 1-5) (1) Reach through the fuse box opening, then push out the cluster panel from the backside. Knockout Cover Fig. 1-5 (g) Remove the knockout cover in the cluster panel, third space from the right. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure Nylon Panel Removal Tool FOR MANUAL TRANSMISSION MODELS ONLY. (Step j) (j) Remove the gearshift knob, then loosen the console panel. (Fig. 1-8) Gearshift Knob Cigarette Lighter Console Panel (1) Do not remove the clip securing the cigarette lighter harness. Fig. 1-8 Nylon Panel Removal Tool FOR AUTOMATIC TRANSMISSION MODELS ONLY. (Step k) (k) Loosen the console panel. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure (n) Remove the glove box under panel. (Fig. 1-12) Nylon Panel Removal Tool Glove Box Under Panel Fig. 1-12 (o) Remove the passenger’s step cover. (Fig. 1-13) Nylon Panel Removal Tool Step Cover Fig. 1-13 Nylon Panel Removal Tool Cowl Cover (p) Remove the passenger’s cowl cover. (Fig. 1-14) (1) Remove the one nut securing the cowl cover. Nut Fig. 1-14 Nylon Panel Removal Tool (q) Remove the glove box assembly. (Fig. 1-15) (1) Release the damper lever.
SCION tC 2007 - SECURITY (V5) Procedure 2. V5 Wire Harness Installation. (Steering Column Area) (a) Locate and disconnect the white 8P connector from the ignition switch area. (Fig. 2-1) 8P (White) Fig. 2-1 (b) Plug in the V5 harness’ white 8P connectors between the vehicle harness’ 8P connector and the ignition switch. (Fig. 2-2) V5 Harness’ 8P V5 Harness’ BLACK Wire V5 Harness’ 8P V5 Harness Fig.
SCION tC 2007 - SECURITY (V5) Procedure Pliers, Side Cutter 4P (White) FOR AUTOMATIC TRANSMISSION MODELS ONLY. (Steps e – f) Wire Side View BLACK 4P Splicing Connector Wire Tie V5 Harness Fig. 2-4 (e) In the ignition switch area, locate the white 4P connector’s BLACK wire (top row, first space from the left). Attach the V5 harness’ BLACK wire with a splicing connector. (Fig. 2-4) (1) Turn the connector so the wires face you and the tab is on top. (2) Verify the correct wire is chosen for splicing.
SCION tC 2007 - SECURITY (V5) Procedure (i) Loosely secure the V5 harness to the vehicle harness with one wire tie below the steering column. (Fig. 2-6) Side Cutter Wire Tie V5 Harness Fig. 2-6 (j) Locate and disconnect the white 17P connector from the steering column area. (Fig. 2-7) 17P (White) (k) Use a small jeweler’s screwdriver to lift up the terminal retainer on the back of the 17P connector. (Fig. 2-8) Fig.
SCION tC 2007 - SECURITY (V5) Procedure Vehicle Harness’ ORANGE Wire Terminal Retainer 1P (Female) Tab 17P (1) The terminal should not come out when pulled lightly from the back. If it does, push it in again. Vehicle Harness Fig. 2-10 (o) Insert the terminal at the end of the V5 harness’ ORANGE wire into the top row, first space from the left of the vehicle harness’ 17P connector, then close the retainer. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure (q) Locate and disconnect the black 12P connector from the steering column area. (Fig. 2-13) 12P (Black) Fig. 2-13 V5 Harness’ 12P (Black) Side Cutter Wire Tie V5 Harness (r) Plug in the V5 harness’ black 12P connectors between the vehicle harness’ black 12P connector and the steering column area. Secure the wire tie previously installed below the steering column. (Fig. 2-14) V5 Harness’ 12P (White) Fig.
SCION tC 2007 - SECURITY (V5) Procedure Side Cutter Wire Tie V5 Harness’ 20P V5 Harness Wire Tie Wire Tie Hood Opener Cable (u) Route the V5 harness toward the driver side cowl area, then secure it to the vehicle harness with three wire ties in the bottom of the driver side J/B. (Fig. 2-17) (1) Route the V5 harness between the dashboard and the hood release cable. Fig. 2-17 4P (Black) Driver Side J/B (v) Route the V5 harness to the driver side J/B area as shown. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure (c) Secure the 20P connectors and the V5 harness to the vehicle harness with one wire tie. (Fig. 3-3) V5 Harness Side Cutter 20P Wire Tie Fig. 3-3 4. V5 Wire Harness Installation. (Driver side J/B area) 6P (White) (a) From the fuse box opening, locate and disconnect the white 6P connector from the left side of the driver side J/B. (Fig. 4-1) Driver Side J/B Fig.
SCION tC 2007 - SECURITY (V5) Procedure 30P (White) (d) From the fuse box opening, locate and unlock the white 30P connector from the upper left side of the driver side J/B, then disconnect it. (Fig. 4-4) Driver Side J/B Fig. 4-4 Jeweler’s and Small Flat Screwdriver Pick Tool (or Wiring Terminal Tool) (e) Using a small flat screwdriver, lift up and slide the 30P connector’s black lock cover to remove it. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure (i) Insert the terminal at the end of the V5 harness’ VIOLET wire into the top row, nine spaces from the left of the vehicle’s harness 30P connector. (Fig. 4-7) 30P V5 Harness’ VIOLET Wire Terminal Retainer Wire Side View VIOLET 30P V5 Harness Fig. 4-7 V5 Harness’ ORANGE ORANGE Wire Terminal (j) Insert the terminal at the end of the V5 harness’ ORANGE wire into the bottom row, ten spaces from the left of the vehicle harness 30P connector. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure Vehicle Harness’ ORANGE Wire Terminal Retainer Vehicle Harness’ VIOLET Wire Terminal (m) Insert the terminal at the end of the vehicle harness’ VIOLET wire into empty 2P connector’s left side opening. (Fig. 4-9) 2P (Female) Wire Side View 2P (1) Turn the connector so the wires face you and the tab is on top. ORANGE VIOLET Fig. 4-9 (n) Insert the terminal at the end of the vehicle harness’ ORANGE wire into the empty 2P connector’s right side opening. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure V5 Harness Vehicle Harness (r) Refit the 30P connector’s lock cover. (Fig. 4-11) (s) Reconnect 30P connector to the driver side J/B. Connector Cover 30P Fig. 4-11 Side Cutter (t) Plug the V5 harness’ 2P male connector into the V5 harness’ 2P female connector. (Fig. 4-12) Wire Tie V5 Harness 2P Driver Side J/B (u) Secure the 2P connectors to the vehicle harness with one wire tie. (Fig. 4-12) Vehicle Harness Fig.
SCION tC 2007 - SECURITY (V5) Procedure V5 Harness (b) Connect the V5 harness’ black 4P connector to the status monitor 4P connector. (Fig. 5-2) V5 Harness’ Black 4P (1) Verify the connectors are plugged in securely. (c) Refit the cluster panel. (Fig. 5-2) Fig. 5-2 Cluster Panel 6. V5 Wire Harness Installation. (From Steering Area to Center Console Area) V5 Harness (a) Route the V5 harness toward the center console area. (Fig. 6-1) Brace V5 Harness Fig.
SCION tC 2007 - SECURITY (V5) Procedure (d) Secure the V5 harness to the vehicle harness with three wire ties in the driver side center console area. (Fig. 6-3) Side Cutter (1) Do not secure the V5 harness to the 10P and 6P connectors’ harness with a wire tie. Wire Ties (x3) V5 Harness Fig. 6-3 Side Cutter (e) Route the V5 harness toward the glove box area, then secure it to the vehicle harness with two wire ties in the passenger side center console area. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure (c) Locate the vehicle harness’ white 1P connector above the passenger side cowl area. The plug the V5 harness’ white 1P female connector into the vehicle harness’ white 1P male connector. (Fig. 7-3) Side Cutter Wire Ties (x2) V5 Harness V5 Harness’ Female 1P Fig. 7-3 Vehicle Harness’ Male 1P 20P (White) (1) If the 10P connector harness is secured to the vehicle harness with breakaway tape, then cut the breakaway tape. Fig.
SCION tC 2007 - SECURITY (V5) Procedure Small Flat Blade Screwdriver 8. V5 ECU, GBS ECU Preparation and Installation. GBS Setting (a) Turn the adjustment screw on the GBS ECU to the “6” position. (Fig. 8-1) GBS ECU Fig. 8-1 (b) Attach one foam tape to the GBS ECU. (Fig. 8-2) Foam Tape GBS ECU Fig. 8-2 V5 ECU Connectors Fig. 8-3 ECU Mounting Bracket GBS ECU (c) Insert the ECU mounting bracket into the indicated bracket slot on the V5 ECU and the indicated bracket slot on the GBS ECU. (Fig.
SCION tC 2007 - SECURITY (V5) Procedure 10mm Socket, Side Cutter Brace Bolts (x2) (d) Connect the V5 harness’ 40P connector to the V5 ECU and 8P connector to the GBS ECU. (e) Locate the two holes in the brace to the right side of the glove box area. Secure the V5 ECU and GBS ECU to the outside of the brace with two bolts supplied in kit. (Fig. 8-4) V5 ECU and GBS V5 Harness Wire Tie Fig. 8-4 (1) Verify the bolts are tightened and secured.
SCION tC 2007 - SECURITY (V5) Procedure Torque Wrench, 10 mm Socket 10. Completing the Installation. (a) Complete the vehicle reassembly. Negative Battery Cable (1) Reconnect any disconnected connectors. Battery (2) Verify the panels fit together properly with no uneven gaps between them. (b) Clean up and remove any trash. Fig. 10-1 Battery (c) Reconnect the vehicle’s negative battery cable. (Fig. 10-1) (1) Position the negative terminal at an angle of ~90° to the battery as shown.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Fit appropriate fuse before beginning. Press and release the remote control’s lock 1. The turn signal lights flash once. button to start the system’s arming process. All doors lock. The Status Monitor’s LED lights up. Wait 30 seconds. 2. After 30 seconds, the LED starts flashing; the system is now armed. Press and release the remote control’s 3.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Reach inside and manually unlock the 8. The driver’s door automatically relocks. driver’s door to trigger an alarm. The horn sounds repeatedly. The headlights flash repeatedly. The turn signal lights flash repeatedly. The LED lights up. Manually unlock the driver’s door again 9. The driver’s door lock attempts to lock and hold it unlocked, open the door, then sit repeatedly.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Press and release the remote control’s 14. The horn stops sounding. unlock button to stop the alarm. All the lights stop flashing. The LED turns off Press and release the remote control’s lock 15. Refer to step #1 and #2. button to start the system’s arming process, then wait 30 seconds until the system is armed. Roll up all windows, remove the key and exit the vehicle.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Insert the key into the driver’s door key 19. The horn stops sounding. cylinder and turn it toward the back of the All the lights stop flashing and/ or turn off.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Seat Belt Warning Light Functioning Seatbelt Warning Light. If the warning light remains "ON", it may indicate a system malfunction. Air Bag Warning Light Functioning Air Bag Warning Light. If the warning light remains "ON", it may indicate a system malfunction ABS Light (if equipped) Functioning ABS Light.
SCION tC 2007 - SECURITY (V5) Checklist - these points MUST be checked to ensure a quality installation.
