SR-i500SW / SR-i600 FM 2-Way Security System INSTALLATION MANUAL AND USER’S GUIDE
Standard Features • • ½ mile 2-Way FM Transceiver LCD Water proof / impact resistant remote Ultra low power drain MCM Built-in accelerometer Ignition protection Range Confirmation Signal (RCS) • • • • • • • • • • • Remote sensor control Battery safeguard with “sleep mode” Violation display with time stamp Passive arming Selectable arming / disarming Programmable multi-tone siren Remote panic feature Optional Accessories • • • • Perimeter sensor (SN-5) – A miniature multi stage microwave sensor that de
Installation Components List MCM (Main Control Module) Remote Transceiver Accessory Harness Generic Installation Kit (GEN-1) Main Harness (HAR-1) Planning the Installation It is very important that before starting the installation of the security system, you carefully read the installation instructions and spend time planning the installation. By planning ahead you will be able to select the best approach in placing, securing and wiring the system to your specific motorcycle.
Mounting the Components Select a suitable location under the seat or in a side cover. Mount the MCM using Velcro or cable ties. Make sure that it is not exposed or easily reached. Routing the Antenna Wire The MCM includes an 18” antenna wire. The first 12” is a coaxial wire; the remaining 6” is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed.
Connections Fuse To Battery (+) Accessory Connector HAR-1 GEN-1 MCM Black – To Ground (-) Grey – To Turn Signal Grey – To Turn Signal Orange – To Tail Light Note: Connect the (HAR-1) harness to the MCM only after installation is completed. If the battery is to be removed, disconnect this connector first. Reconnect only after battery terminals are reconnected. Note: When the main harness (HAR-1) is plugged in, the siren should chirp.
User’s Guide Remote Transceiver Icons and Message Displays Alert Type Aud/Vibr System Status Signal Indicator Audible/ Silent Alert Indicator Perimeter Trigger Tilt Trigger Shock Trigger Ignition Trigger Battery Level Indicator Clock Back up Power Activated Button # 1 Button #2 Button #3 Button #4 Charger Input Transceiver Charging Instructions The transceiver is pre-charged at the factory and will operate out of the box but we recommend that it be charge for at least 10 hours when first opera
Turning the Transceiver On/Off Note: • • Out of the box the transceiver is turned “off” by default and should be turned “on” to operate the alarm To turn “on” , press and hold button #4 until the transceiver chips two times. The power is now “on”. To turn “off”, press and hold button #4 until the transceiver chips two time followed by another two times. The power is now “Off”.
Alarm Triggers When the system is triggered, the siren will sound and the turn signal lights will flash. The Transceiver’s LCD will display the following messages: 1. icon. The siren on the bike will sound for 5 If bike is bumped, the LCD displays seconds and the lights will flash. This cycle will repeat twice. 2. If the perimeter sensor triggers a full alarm cycle, the LCD displays on the bike will sound for 5 seconds.
Motorcycle Battery Status When the voltage on the motorcycle battery drops below 11.2 volts The LCD displays icon. Locking the Transceiver’s buttons To “lock”, press button #4 for 2 sec. The Transceiver will beep and buttons will lock. To “unlock”, press button #4 for 2 sec. The Transceiver will beep and buttons will unlock. Checking Motorcycle Status and Violation Display with Time Stamp 1. 3. Press button #4. The back light and the memory screen will be displayed.
Programming and Customizing Instructions There are two types of programming mode: 1) Programming the Transceiver- To program the transceiver the MCM does not have to be installed or be within range. The programmable modes for the Transceiver are: • Transceiver Alert Type (Audible/Silent Vibrate). • Clock. 2) Programming the MCM- To program the MCM the system must be installed, with in range, and in the disarmed mode. The programmable modes for the MCM are: • Auto/Manual Arming.
Selecting Auto/Manual Arming Enter the programming mode. Scroll to the icon and Press Button #1 to enter the arming selection screen. The LCD will display the current setting ([Act] or [PAS]) and the siren will chirp two or three times. To program follow these steps: 1. Press button 2 to toggle between the alert options 2.
Setting Clock Time 1. Enter the programming mode. 2. 3. 4. Press button #4 repeatedly until the icon begins to flash. Press button #1 to select and enter clock setting mode. Press button #1 to scroll through ‘hour’, ‘minute’ settings. The selected item will be flashing. Press button #2 to adjust the setting of the selected item. Press button #4 to save setting and exit, or press button #3 to abort. 5. 6. Encoding a Transceiver Note: Transceivers are programmed from the factory.
Optional Accessories Perimeter Sensor (SN-5) Mounting the SN-5 The Perimeter sensor uses high frequency microwave technology to detect mass density movement around the motorcycle. The signal can transmit through the seat, fiberglass, leather and plastic, but not metal. It is recommended to place this sensor under the seat as close as possible to the center of the motorcycle.
Ignition Disable / Anti-hijack Module (RID-5) Installation 1. 2. 3. 4. 5. 6. 7. 8. Cut the Ignition / Engine control wire (refer to options below) Attempt to start bike to test if correct wire is selected. If bike starts the wrong wire is selected. (contact Aritronix for assistance) If bike does not start, correct wire was selected continue to step 3. When Packaged the RID-5 wire ends have been treated with clear silicon to protect the ends from fraying.
Back-up Battery (BAT-5) The back-up battery provides the system the ability to transmit information and activate the siren when power is interrupted. If power is ever interrupted while the system is activated the back-up battery will be engaged, the transceiver will receive a full alarm and the siren will sound in 25 second increments. If power is not restored the alarm will continue to transmit and sound for six cycles.
Limited Warranty Scorpio-branded security products come with a 2-year (from time of purchase) limited warranty. This includes all components and accessories that are manufactured by Aritronix Ltd. The following sections describe the limited warranties. What is covered by this limited warranty? This limited warranty covers defects in materials and workmanship in your — our end-user customer's — Scorpio-branded hardware products, including Scorpio-branded accessory products.