User's Manual

TURNINg ON/OFF
ON: The BT1000 will switch on automatically when the ignition key is turned. Wait until you hear “Power on”
and the blue LED indicator light is on for 3 seconds. To turn on/off manually press & hold MFB for 3 seconds.
Press the “MFB” button for 3 seconds if you have turned the ignition key. Until you hear “power on” and the Blue
LED indicator light 3secs.
OFF: The BT1000 will turn off automatically when the ignition is off. Press the “MFB” button for 3 seconds if you
have turned the ignition key. Until you hear “power off”.
mANUAL PAIRINg
1. Power off the BT1000.
2. Press and hold the Multi-function Button (MFB) for 6 seconds until you hear the announcement “Power on”
followed by the announcement “Pairing phone - please place your phone in pairing mode and enter PIN code
“0000”. The blue LED will flash every (1) second.
3. Activate the Bluetooth feature from your phone’s menu. The phone will search all Bluetooth devices within 10
meters (30 ft.) and display them as a list.
4. Select “BT1000” from the list. Enter “0000” to pair and connect the BT1000 to your phone. If you are using
an Apple iPhone, you can just hit “OK” to pair to the BT1000.
5. The blue LED will blink when both devices are successfully paired, and you will hear the BT1000 announce:
“Pairing successful”.
Note: If the pairing cannot be completed with 2 minutes of pairing mode activation the BT1000 will power
down. The BT1000 will announce “Pairing failed - please put your phone in pairing mode and try again.” Please
repeat steps 2 through 4.
CONNECTION
If the BT1000 and the mobile phone are disconnected, connection may be restored by the following steps:
1. If the BT1000 has been switched off, turn on power and the connection will be restored automatically if set to
“Trusted” on phone”.
2. If the mobile phone has been switched off, turn on the mobile phone and restore the connection either through
the phone’s menu or by pressing the MFB once.
3. If the BT1000 and phone are out of range, make sure the devices are within working range (10 meters) and
press the MFB once.
Note: Once the connection is successful the BT1000 will announce “Phone is ready for use,” and the blue LED will
flash every 3 seconds.
DISCONNECTION
If the BT1000 needs to be disconnected from the phone connection (Example: To connect your phone to another
device) the device may be disconnected using the following steps:
1. Turn off the BT1000.
2. Disconnect the BT1000 using the phone’s menu.
Note: Once disconnection is successful the BT1000 will announce “Disconnect complete.”
EASy PAIRINg
Note: The BT1000 must be paired with your mobile phone before use.
The BT1000 includes an “Easy” pairing feature that will automatically re-connect it to the most recently paired
device. If the most recent device is not present within 5 seconds, then the BT1000 will AUTOMATICALLY go into
pairing mode and you will hear the announcement “Power on” followed by the announcement “Pairing phone -
please place your phone in pairing mode and enter PIN code 0000”. The blue LED with flash every (1) second.
3
INSTALLATION
WIRINg
Yellow: +12V Constant
Connect the Yellow wire to a +12V constant power source (continuous power). We
recommend the battery positive terminal. This wire must be connected for the
system to
function correctly.
Red: +12V Switched
Connect the Red wire to a +12V switched IGN or ACC power source in the vehicle
(controlled with the vehicle key).
Black: <->12V Ground
Connect to the metal body of the vehicle using a sheet metal screw and a star
washer to ensure a good ground. Scrape away any paint or debris from the ground
location.
Pink: <-> Negative Mute Output
Connect to the Negative “Phone” or “Mute” input of stereo (if available). Some car
stereos include an input wire to be used with a cellular phone kit. Refer to your
stereo’s user guide to see if you have this connection available.
FIgURE 2
6
PAIRING, CONNECTION & DISCONNECTION