manual

Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
FRONT OF KIT
FRENTE DE
ESTUCHE
"A1" BRACKET
USE HOLE #4
"A1" SOPORTE USA
ABERTURA
NO. 4
"B1" BRACKET USE HOLE #1
"B1" SOPORTE USA
ABERTURA
NO.1
"D2"
BRACKET USE HOLE #1
"D2" SOPORTE USA ABERTURA NO. 1
"C2" BRACKET
USE HOLE #4
"C2" SOPORTE USA ABERTURA NO. 4
Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"A1" BRACKET USE HOLE #4
"A1" SOPORTE USA
ABERTURA NO. 4
"B1" BRACKET
USE HOLE #2
"B1" SOPORTE USA
ABERTURA
NO.2
"B2" BRACKET
USE HOLE #3
"B2" SOPORTE USA
ABERTURA NO. 3
"C2" BRACKET
USE HOLE #4
"C2" SOPORTE USA ABERTURA NO. 4
FRONT OF KIT
FRENTE DE
ESTUCHE
Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO
DERECHO
LEFT SIDE
LADO
IZQUIERDA
"A1" BRACKET USE HOLE #2
"A1" SOPORTE USA
ABERTURA NO. 2
"B1" BRACKET USE HOLE #2
"B1" SOPORTE USA ABERTURA NO.2
FRONT OF KIT
FRENTE DE
ESTUCHE
19
1986-88 Chevrolet Monte Carlo
1986-87 Chevrolet El Camino
RADIO REMOVAL:
1. Remove the two
screws from the top
of the radio trim panel
and the two screws
from the bottom
edge of the trim panel.
2. Remove the four screws
which secure the radio,
slide the radio out of the
dash cavity and
disconnect
the wiring connectors.
3. Remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1985-88 Chevrolet Nova
RADIO REMOVAL:
1. Remove the ashtray and extract the two screws from the
ashtray bracket. Then remove the bracket.
2. Extract the two screws
from the top edge of the
radio trim panel, pull the
trim out and remove the panel.
3. Remove the four screws which
secure the radio to the dash,
slide the radio out of the
dash cavity, disconnect the
wiring harnesses and
remove the radio.
4. Remove the two hex
nuts from the factory
radio mounting bracket,
one from each side of the radio, and remove the bracket from the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1998-01 Chevrolet S-10 Blazer
1998-01 Chevrolet S-10 Pickup
1998-01 GMC S-15 Jimmy
1998-01 GMC Sonoma Pickup 1998-00 Isuzu Hombre Pickup
RADIO REMOVAL:
1. Extract the (2) screws
securing the top area
of the driver's side
underdash cover panel.
2. Pull the driver's side
underdash down to
access and extract
(2) 7mm hex screws
holding the bottom
of the dash bezel.
3. Extract the screw located in the top edge
of the dash panel at the instrument cluster.
4. Carefully pry out on the dash bezel to release the fastening clips securing the bezel to the dash and
unplug headlight / misc. switches on the driver's (left) of the bezel.
CAUTION: At this point, take care around the hazard switch, by tilting the wheel down and/or depressing the
switch so the panel will clear. Also take care to snap the passenger air bag switch from the dash panel and
push it back trhough its own hole rather than unplugging the switch. It is a costly repair bill in excess of $400
to replace the hazard switch.
5. Remove the dash bezel from the vehicle.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.