Owner's Manual

ManualsBrandsScosche ManualsAudio accessories & installationDash and Wiring Kit

Table Of Contents

Installation Instructions

~~C3~,...,.,~:·

GM5207B

IN-DASH STEREO INSTALLATION

KIT

FOR

2013-UP

CHEVROLET

MALIBU

WITH TOUCH-SCREEN INTERFACE

INTRODUCTION/PRELIMINARY

This premium installation kit is for 2013-Up Chevrolet Malibu vehicles. Included are all the parts you need to

mount your car stereo or CD player into your vehicle's dash. Refer

the individual instruction in this manual to

remove your vehicle's factory radio and assemble the kit.

CAUTION

DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP

PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST

LIGHT

CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE

THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID

ALL

FACTORY AIRBAG WIRING •

AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY

DEATH.

NOTES

• See your vehicle's instructions for any special tools your installation might require.

• Read all instructions accompanying your car stereo for proper wiring and mounting instructions.

IMPORTANT

NOTE:

ensure

proper

functionality,

cycle

the

ignition

key

from

"Off"

"Run"

TWO

times

(2X)

after first

connecting

the

interface

your

vehicle.

For

questions

call

at:

(800) 363-4490

Ext

LIABILITY DISCLAIMER

This instruction booklet is based on carefully documented data and research

automobile dash disassembly, wire harness/

codes and information pertaining

installation of this kit (GM5207B)

2013-Up Chevrolet Malibu vehicles. Scosche

Industries, Inc.

cannot

held responsible for discrepancies/inconsistencies that may occur due to the automobile

manufacturing changes

options, or damage that may occur in the automobile during the installation of components while

using this booklet.

you

have

any

further

questions,

call

our

toll

free

technical

help

line

at:

1-800-621-3695x3

C2014 SCOSCHE INDUSTRIES, INC.

GM5207B (3000590) 4/14

Summary of content (12 pages)

PAGE 1
a ~~C3~,...,.,~:· GM5207B IN-DASH STEREO INSTALLATION KIT FOR 2013-UP CHEVROLET MALIBU WITH TOUCH-SCREEN INTERFACE INTRODUCTION/PRELIMINARY This premium installation kit is for 2013-Up Chevrolet Malibu vehicles. Included are all the parts you need to mount your car stereo or CD player into your vehicle's dash. Refer to the individual instruction in this manual to remove your vehicle's factory radio and assemble the kit.
PAGE 2
PARTS LIST 1. Main panel with built-in touch screen (*) 2. Stereo mounting bracket Oeft) 3. Stereo mounting bracket (right) 4. Dash pocket for single din mount 5. Power harness (not shown-see page 3) SOLD SEPARATELY: CAMOSM OnStar retention interface (not shown -see page 4) 2 3 4 FACTORY STEREO REMOVAL 2013-UP CHEVROLET MALIBU 1. 2. 3. 4. 5. 6. 7. 8. Use a panel remove tool (PRl) To unclip and remove shifter bezel. Use a PRT to unclip and remove behind key cylinder.
PAGE 3
STEREO ASSEMBLY I MOUNTING SINGLE DIN ISO INSTALLATION 1. Attach 6552 pocket to 7428 panel using supplied screws (see inset). 2. Attach 7429 and 7430 brackets to 7428 panel using supplied screws. 3. Align and attach aftermarket single DIN stereo to the Panel and bracket assembly using the screws supplied with the stereo. 4. Reconnect aftermarket stereo and finish reassembly. 7430 LEFT MOUNTING BRACKET 7429 RIGHT MOUNTING BRACKET DOUBLE DIN ISO INSTALLATION 1.
PAGE 4
GM5207B WIRING DIAGRAM 3.5mm Steering Wheel output r-------- It, I -~!il IJl !I ~ ~ USB for Interface nrmware update ONLY CAMOSM OnStar retention module {Sold separately) [bypassplug) t _ _ _ _ _ _ _ _l GM5207B WIRE COLOR CODES AFTERMARKET RADIO NAVIGATION CONNECTIONS (OptlonaQ Pink= Vehicle speed pulse signal (VSS) Violet/White = Reverse light trigger (+12V when in reverse gear) Telephone Mute (-12V Neg. Brown Mute input for cell hands-free kit} Parking Brake trigger Lt.
PAGE 5
INITIAL VEHICLE I OPTIONS SETUP IMPORTANT NOTE: To ensure proper operation of the touch-screen climate control, you must first set the unit to match your vehicle model, HVAC controls and factory-equipped options. Follow the steps below after you have connected the UAC and completed the initial power up stage by cycling the Ignition key from OFF to ON/RUN Two times (2X). 1. Press the power button (page 6, Fig. 3, #4) to power on the touch screen controls. 2. Press and Hold the SET button (page 6, Fig.
PAGE 6
CLIMATE & CONVENIENCE CONTROLS The combination button panel/touch screen unit replaces the factory climate, convenience and personalization controls built into the OEM Factory GM Radio system. This solution provides improved ergonomics while adding touch screen capabilities unique to this system. Read the following sections to familiarize yourself with the operating controls and settings. FIGURE 3 2 1-----+-1+- , Control Panel Button layout - 3 }-----+-11- 1. Fan speed UP 2. Fan speed DOWN 3.
PAGE 7
CLIMATE & CONVENIENCE CONTROLS FIGURE 4 Home TFT Color Touch Screen layout (SINGLE Climate Control System) 1. Air Temp Up 2. Air Temp Down 3. Max A/C On/Off Temp range 4. Vent Mode 5. Fan Speed Indicator TOUCH SCREEN CONTROLS - SINGLE CLIMATE CONTROL SYSTEM TEMPERATURE CONTROL Use the UP and DOWN arrows (Fig. 4, #1 & #2) on the color TFT touch screen to adjust vehicle air temperature. Touch the Red arrow to increase air temp. Touch the Blue arrow to decrease air temp.
PAGE 8
CLIMATE & CONVENIENCE CONTROLS FIGURE 5 Home TFT Color Touch Screen layout (DUAL Climate Control system) 1. 2. 3. 4. 5. 6. 7. 8. 9. Driver's Temp Indicator Driver's Temp Up Driver's Temp Down Max A/C On/Off Driver's Heated Seat Auto Climate Control Fan Speed Indicator Passenger's Heated Seat SYNC {Driver/ Passenger Temp) 10. Passenger's Temp Down 11. Passenger's Temp Up 12. Passenger's Temp Indicator 13.
PAGE 9
CLIMATE & CONVENIENCE CONTROLS cont'd from page 8 HEATED SEATS Touch the driver's seat heater button (pg. 8, Fig. 5, #5) on the color TFT touch screen to turn on the driver's seat heater. The engine must be running to use heated seats. A Button graphic will show the level of heat selected (low, medium, or high). Press the button repeatedly to cycle through the temperature settings or to turn the heated seat OFF. Touch the passenger's seat heater button (pg. 8, Fig.
PAGE 10
VEHICLE FEATURE I SETTINGS The color TFT touch screen interface is used to access the vehicle's built-in customization features. VEHICLE SETTINGS MENU Press the "SET" button (see page 6, Fig. 3, #B) on the control panel to access the user controlled features and settings. The "Settings" Home Screen will appear (see page 9, Fig. 6). Press the "CAR" button (see page 9, Fig. 6, #2) to access the vehicle features list as shown in Fig. 7 (below).
PAGE 11
VEHICLE FEATURE I SETTINGS cont'd from page 10 FEATURE TITLE Remote Lock, Unlock, Start SPECIFIC FEATURE DESCRIPTION SETTING 1 Unlock Feedback (Lights) On Off Lock Feedback (Lights/Horn) Lights & Horn Chirp Lights Only Door Unlock Driver Door All Doors Remote Left in Vehicle Reminder On Off Relock Remote Door On Off Passive Door Unlock Driver Door All Doors Passive Door Lock On Off SETTING2 Aftermarket Radio Type Sets Steering Wheel Control Output Select: Alpine, Clarion, JVC, K
PAGE 12
To ensure proper functionality, cycle the ignition key from "Off" to "Run" TWO times (2X) after first connecting the interface to your vehicle.