Owner's Manual

ManualsBrandsScosche ManualsCar Audio & VideoScosche HD7000A Dash Kit

.SC:O.Sc=f

It:

HD7000AB

AFTERMARKET STEREO INSTALLATION

KIT

FOR SELECT HARLEY-DAVIDSON

2006-2013

FLHX STREET GLIDE,

1996-2013

FLHT

ELECTRA GLIDE

1998-UP FLTA ROAD GLIDE MODELS

(WITH FACTORY-EQUIPPED RADIO)

PARTS INCLUDED:

1. DASH

KIT

(1)

Mounting

Panel

(2)

Left

Right Mounting Brackets

(4)

Screws (bracket attachment)

(2)

Spacers (*Road

Glide models only)

2. NEOPRENE

GASKET STRIP

(not shown)

OPTIONAL

ACCESSORIES:

(Sold separately)

HDSWC 1

Handlebar Control

Interface w/plug

and

play

harness

HD01

B Power/Speaker harness

(For non-handlebar

control

cycles)

7424

LEFT

MOUNTING

BRACKET

7422

MOUNTING

PANEL

INTRODUCTION/PRELIMINARY

7501

SPACERS*

7423

RIGHT

MOUNTING

BRACKET

This premium

installation

kit is

for

select

Harley Davidson Road

Glide

Street Glide

motorcycles

Included

are

all

the parts you need

mount your car stereo

player

into your bike's dash. Refer

the individual instructions in this manual

remove your factory radio and assemble

the kit.

CAUTION

DISCONNECT

THE

CYCLE

S NEGATIVE BATTERY .TERMINAL

BEFORE THE INSTALLATION TO

HELP PREVENT

ELECTRICAL DAMAGE. WE RECOMMEND THE

USE OF

VOLT/OHM METER

OVER

TEST LIGHT TO

CHECK

WIRING.

TEST LIGHT OR

GROUNDED

WIRE PROBE

CAN

CAUSE

DAMAGE

THE CYCLE•s COMPUTER

AND/OR

DIAGNOSTIC SYSTEMS.

PREPARATION:

•

Work on a clear level

surface • Place bike on kickstand with wheel tilted

toward the

leaning direction

•

Use

felt

soft cloths

cover and protect painted surfaces

TOOLS REQUIRED

(not

Included):

T-25/T-27

Torx

1/4''

6mm hex drive

3/16''

Smm hex drive

7/16''

socket

box

wrench (Road

Glide

models only)

LIABILITY

DISCLAIMER

This manual is

based

carefully documented research. Absolute accuracy is attempted, but not guaranteed.

Use the

manual

as a reference guide as your bike may differ.

Scosche Industries, Inc. cannot be

held responsible

for

Inconsistencies that may occur due to vehicle manufacturing changes or options,

damage that may occur

the

vehicle

during the

Installation

components

while

using this

booklet.

If you have any further questions,

call

our

toll

free technical

help line

at:

1·890·621-3695x3

2014

SCOSCHE

INDUSTRIES,

INC

HD7000AB

(3000597)

7/14

Summary of content (8 pages)

PAGE 1
rJ .SC:O.Sc=f I t : HD7000AB AFTERMARKET STEREO INSTALLATION KIT FOR SELECT HARLEY-DAVIDSON 2006-2013 FLHX STREET GLIDE, 1996-2013 FLHT ELECTRA GLIDE & 1998-UP FLTA ROAD GLIDE MODELS (WITH FACTORY-EQUIPPED RADIO) PARTS INCLUDED: 7501 SPACERS* 1. DASH KIT 7424 LEFT MOUNTING (1) Mounting Panel BRACKET (2) Left & Right Mounting Brackets (4) Screws (bracket attachment) (2) Spacers (*Road Glide models only) 2.
PAGE 2
FACTORY STEREO REMOVAL 2006-2013 FLHX STREET GLIDE 1996-2013 FLHT ELECTRA GLIDE 0 Drape a protective cloth over the front fender. Extract (3) T-27 Torx bolts from bottom edge of windshield. Carefully lift away windshield, store in a safe location and replace the middle Torx bolt for support during the remaining removal steps. Extract (2) T-27 Torx bolts from outer side of the fairing (under mirrors). Extract (2) T-27 Torx bolts from inside the fork tubes (facing forward).
PAGE 3
FACTORY STEREO REMOVAL ~ While supporting the outer \.:1 fairing, remove the middle windshield bolt, lift away and unplug headlight to remove fairing shell. Store fairing in a safe place until re-assembly. Unbolt and remove inner fairing support brackets from each side (3/16" hex & T-25 Torx screws) Note that the Torx screw is also a shared speaker screw. Extract (2) 1,4'' 6mm hex bolts from each side of the radio housing.
PAGE 4
FACTORY STEREO REMOVAL 1996-UP FLTR ROAD GLIDE 0 Drape a protective cloth over the front fender. a DO NOT remove the windshield on Road Glide models Extract (2) T-25 Torx bolts from bottom left and right sides of the fairing. Use a 7/16" socket or box wrench to remove (2) nuts that hold the each turn signal at the lower fairing. Remove the metal strap under the nuts, and push the studs out to remove the signals. CAUTION: Do not let turn signals drop or dangle.
PAGE 5
FACTORY STEREO REMOVAL Have a helper hold on the outer fairing and extract the last (2) T-25 Torx bolts from the upper fairing near the speaker grilles. Carefully lift fairing at headlights to release support hooks, unplug headlights and remove. Store fairing in a safe place until reassembly. NOTE!: Be sure to reattach support hooks during reinstallation. Extract (2) W' 6mm hex bolts from each side of the radio housing.
PAGE 6
KIT ASSEMBLY REMOVE SLEEVE FROM AFTERMARKET STEREO 1. Locate the locking mechanism on your DIN stereo sleeve {typically) on the side. 2. Slip mounting sleeve towards rear of stereo FIGURE and remove {Figure 1). 1 ISO-DIN MOUNT ONLY 1. Attach the 7423 and 7424 side brackets to the 7422 front panel using the hardware supplied with the kit (Figure 2). 2. Remove supplied trim ring and sleeve from new stereo. 3.
PAGE 7
PAGE 8