Owner's Manual

ManualsBrandsScosche ManualsAudio accessories & installationDash Kit

•

HD7001B

HD14UBN

ICHD2BN

ISO-DIN INSTALLATION KIT FOR

2014-UP HARLEY DAVIDSON TOURING MODELS

(7730)

Left Bracket

(7729)

Face Panel

Tools Required:

3/16 Allen Wrench

T27

Tone

•

Table of Contents

(7731)

Right Bracket

Made

U.S

.A.

with

over

90%

Parts

Kit

Overview

...... ......

...........................

... Pg. 1

2014-UP

Street

Glide Disassembly

...............

Pg.

2-3

2014-UP

Electra

Glide

Disassembly

...............

Pg.

2-3

2014-Up

Ultra

Glide Disassembly ..•..

...

......

2-3

2015-UP

Road

Glide

Disassembly

...

..........

. Pg.

4-5

Overview

& Kit Assembly

Step

..............

...

. 6

Kit

Assembly

Steps

2-4

........

..........

.........

Pg. 7

Notes

........

.........

.................

....................

Pg.8

T25

Tone

Phillips Screwdriver

INTRODUCTION/PRELIMINARY

This

premium

installation

kit

for

2014-

Harley Davidson

Bat

Wing

Fairing vehicles

witb

bas

model

radio (dash

modification

required}. Included are all

the

parts

you

need

mount

your

car

stereo

player

into

your

vehicle's dash.

Refer

individual instruction

this

manual

remove

your

vehicles

factory

radio and assemble

the

kit.

CAUTION: DISCONNECT

YOUR

VEHICLE

NEGATIVE

BATTERY

TERMINAL

BEFORE

THE

INSTALLATION

HELP

PREVENT

ELECTRICAL

DAMAGE.

RECOMMEND

THE

USE

A VOLT/

OHM

METER

OVER

TEST

LIGHT

CHECK

WIRING. A

TEST

LIGHT

GROUNDED

WIRE

PROBE

CAN

CAUSE

DAMAGE

THE

VEHICLE'S

COMPUTER

AND/OR DIAGNOSTIC

SYSTEMS.

AVOID

ALL

FACTORY

AIRBAG

WIRING -

AIRBAGS

CAN

ACCIDENTALLY

DEPLOY

CAUSING

SERIOUS

INJURY

DEATH.

NOTES--------------------------

•

See

your

vehicle's instructions

for

any

special tools

your

installation

might

require.

•

Read

all instructions accompanying

your

car stereo

for

proper

wiring

and

mounting

instructions.

[s10P

IMPORTANT!

NOT

RET

URN

PRODUCT

THE

RETAILER

IF YOU

NEED

ASSISTANCE

REPLACEMENT

PARTS

CALL

TOLL

FREE

1800·621·3695

HOURS

MON.FRI

8AM·5

J0PM

(PST) SATURDAY

8AM·2PM

(PST)

LIABILITY DISCLAIMER

This instruction booklet

based

carefully documented data and research

automoblle disassembly, wire harness/codes

and information pertaining

the

installation

this

kit

Scosche Industries, Inc. cannot be held responsible

for

discrepancie

Inconsistencies

that

may occur due

the

automoblle manufacturing changes

options, or damage

that

may occur in the

automobile during

the

installation

components while using this booklet.

you

have

any

further

questions,

call

our toll

free

technical help line

at:

1-800-621-3695x3

@2016

SCOSCHE

INDUSTRIES

INC.

3000619 HD70018 04/

Summary of content (8 pages)

PAGE 1
HD7001B HD14UBN ICHD2BN ISO-DIN INSTALLATION KIT FOR 2014-UP HARLEY DAVIDSON TOURING MODELS (7730) Left Bracket (7731) Right Bracket Made In U.S.A. with over 90% U.S. Parts Table of Contents Kit Overview ...... ...... ........................... ... Pg. 1 2014-UP Street Glide Disassembly ............... Pg. 2-3 2014-UP Electra Glide Disassembly ............... Pg. 2-3 2014-Up Ultra Glide Disassembly..•.. ... .......... Pg. 2-3 2015-UP Road Glide Disassembly ..... - ........... Pg.
PAGE 2
INSTALLATION GUIDE Kit Disassembly Harley Davidson Street Glide, Electra Glide and Ultra Limited models 2014-UP DISASSEMBLY Step 1 Disassembly Disconnect battery to prevent any short circuit to the motorcycle's electronics. Step 2 Loosen Disassembly Carefully remove the (3) screws securing the windshield to the fairing and remove wind shield.
PAGE 3
INSTALLATION GUIDE Kit Disassembly Step 5 Disassembly With outer fairing removed locate the (2) exposed screws securing the air ducts then slide and remove from its location. SAMPLE IMAGE Step 6 Disassembly Remove {11) screws securing the radio to the bracket, then remove. SAMPLE IMAGE Step 7 Disassembly Remove the (3) screws that are securing the gauge cluster. SAMPLE IMAGE Step 8 Disassembly Remove (4) Allen screws from the side of the radio, then slide out and unplug.
PAGE 4
INSTALLATION GUIDE Road Glide Disassembly Harley Davidson 2015-UP Road Glide DISASSEMBLY Step 1 Disassembly Disconnect battery to prevent any short circuit to the motorcycle's electronics. Step 2 Disassembly Remove the (4) screws securing the windshield (Circled on Image) then remove. Step 3 Disassembly Remove the top plastic portion of the fairing and set aside for later install. Step 3 Disassembly Remove the top plastic portion of the fairing and set aside for later install.
PAGE 5
INSTALLATION GUIDE Step 5 Road Glide Disassembly Continued Disassemb/'y' Carefully, using a pry tool remove the speaker grills off. NOTE: (1) rubber tab on the outside and (2) tabs towards the inside. (Tab locations Indicated by rectangular highlights) Step 6 Disassemb/'y' Remove outer (1) tone screw exposed and repeat on the opposite speaker to loosen the fairing NOTE: The fairing is now loose; however, it will sill remain attached until unsnapped away from motorcycle (See Step 7).
PAGE 6
INSTALLATION GUIDE Road Glide Disassembly Continued Step 8 Disassembly Remove (4) Allen screws from the side of the radio, then slide out and unplug radio.
PAGE 7
INSTALLATION GUIDE Step 2 Single DIN Assembly Single DIN Assembly With both left and right brackets screwed onto the face panel (7729), slide the afterrnarket radio in-between the two brackets. Step 3 Single DIN Assembly Adjust the aftermarket radio to the bracket mounting holes, then screw and secure. Step 4 Single DIN Assembly Reass:mble ConTlect In order to complete the installation process for your new kit, you must first reassemble everything in reverse order of disassembly.