Owner's Manual

ManualsBrandsScosche ManualsAudio accessories & installationDash Kit

IN-DASH INSTALLATION KIT

FOR 1999-UP MERCURY VILLAGER

AND NISSAN QUEST

MN1377

PRELIMINARY PARTS LIST

CAUTION:

ª sª $ISCONNECTªªYOURªVEHICLEgSªNEGATIVEªBATTERYªCABLEªBEFOREªREMOVINGªTHEªRADIOPROCEEDINGªWITHªINSTALLATION

NOTES:

ª sª 3EEªYOURªVEHICLEgSªINSTRUCTIONSªFORªANYªSPECIALªTOOLSªYOURªINSTALLATIONªMIGHTªREQUIRE

ª sª 2EADªALLªINSTRUCTIONSªACCOMPANYINGªYOURªCARªSTEREOCASSETTEªPLAYERªFORªPROPERªWIRINGªANDªMOUNTING

instructions.

Tabs

s Instructions

s Mounting Panel

s Snap Shaft

Parts List:

ILLUSTRATION A

DIN TRIM RING

SNAP SHAFT TABS

MOUNTING

PANEL

1.5 CD SNAP POCKET

ASSEMBLING THE KIT

REAR VIEW OF

MOUNTING PANEL

1.5 CD

SNAP

POCKET

ILLUSTRATION B

s 1.5 CD Snap Pocket

s DIN Trim Ring

POCKET INSTALLATION:

1. Locate & align bottom guides and top snaps of the

pocket to kit panel.

2. Slide pocket on bottom guides while the top snaps

are aligned.

3. When aligned properly the top pocket snaps will lock

to kit panel.

RADIO REMOVAL AND IN-DASH INSTALLATIION

1999-Up Mercury Villager

1999-Up Nissan Quest

RADIO REMOVAL:

1. Open the drink holder ashtray assembly. Push in on the tabs near the rear of the sliding tracks to release

the assembly and remove.

2. Extract (2) screws from the ashtray/cup holder cavity.

3. Carefully pry out on the complete radio/climate center dash bezel to release fastening clips.

4. Pull the top half of the bezel away carefully unhooking the bottom half to release, and remove.

5. Extract (4) screws holding the radio in, unplug, and remove.

MOUNTING THE RADIO

SHAFT MOUNT RADIOS:

Snap the supplied shaft tabs into place

and using the hardware supplied with

the radio, secure the radio to the

mounting panel as shown.

ILLUSTRATION C

SHAFT RADIO'S

SUPPLIED

FACEPLATE

DIN RADIOS:

The kit comes DIN ready. Following

the instructions supplied with the radio,

secure the radio to the mounting kit.

RADIO'S

SLEEVE

REAR

SUPPORT

STRAP

SHAFT

RADIO

FACTORY DIN

TRIM RING

SCOSCHE DIN

TRIM RING

SNAP SHAFT

TABS

MN1377

MOUNTING

PANEL

MN1377

MOUNTING

PANEL

DIN

RADIO

VARIOUS REAR SUPPORT STRAP SAMPLES

CAUTION:

Rear support is essential to

the installation's structural

integrity.

FACTORY WIRE CODES

NOTE:

s All wire codes are viewed as looking at the front of the plug with the wires exiting the rear.

sª 5SEªTHESEªWIRINGªCODESªASªAªGUIDEª9OURªVEHICLEªMIGHTªDIFFER

1998-UP Ford, Lincoln, Mercury Vehicles

5 Volt Differential input:

1 = Right Front Negative (RF-)

2 = Right Front Positive (RF+)

3 = Right Rear Negative (RR-)

4 = Right Rear Positive (RR+)

5 = Not Used

6 = Not Used

7 = Grounding Dimmer

8 = Illumination

9 = Amp Ground

10 = Left Front Negative (LF-)

11 = Left Front Positive (LF+)

12 = Left Rear Negative (LR-)

13 = Left Rear Positive (LR+)

14 = Chassis Ground (12V-)

15 = +12V Accessory Switched

16 = +12V Constant Battery

REAR

SUPPORT

STRAP

1995-UP Nissan Vehicles

Rear Speaker Plug:

1 = Right Rear Negative (RR-)

2 = Left Rear Positive (LR+)

3 = Left Rear Negative (LR-)

4 = Empty

5 = Right Rear Positive (RR+)

6 = Empty

Power and Front Speaker Plug:

1 = Chassis Ground (12V-)

2 = Variable Illumination/Dimmer

3 = Battery/Constant (12V+)

4 = Power Antenna

5 = Right Front Negative (RF-)

6 = Left Front Negative (LF-)

7 = 12V Ignition/Switched (12V+)

8 = Illumination/Dimmer

9 = Right Front Positive (RF+)

10= Left Front Positive (LF+)

SCOSCHE STEREO INSTALLATION COMPONENTS STEREO DASH KITS