Installation Instructions

ManualsBrandsScotsman ManualsCubersScotsman C0522 Prodigy Plus

Installation and Operation of the TPDL1 Prodigy Smart-Board™

Datalogger

Scotsman's Advanced Feature Smart-Board is an optional add on electronic device that can be

applied to most Prodigy models. It can be used:

•

With the standard controller

•

With the standard controller and the SmartLock Out Control (KSL)

•

With the standard controller and the Vari-Smart™ Ice Level Control (KVS)

•

With the standard controller, and both the KSL and the KVS

Smart-Board abilities include:

•

USB connection to Scotsman's Prodigy TechTool software

•

Data Logging

•

Data Display

Kit Contents

•

Pre-mounted Smart-Board, connecting cable, USB cable, CD-ROM.

Installation: Temporary Data Logger

1. Depress and hold the Off button until the machine shuts Off (Status light will go out).

2. Disconnect electrical power from the ice machine.

Note: Connecting the TPDL1 to a controller that is powered is NOT recommended, as it

might result in a reset of the controller.

3. Remove front panel.

4. Remove screw holding control cover to control box, swing control & cover open.

5. Route wire into back of control box. Locate datalogger in a secure spot in the cabinet.

6. Connect supplied wire from Smart-Board box to main controller Accessory connection.

7. Close the control box cover.

8. Reconnect electrical power. Display will show time and date (US Central Time). See time set

section for instructions on changing the time. The prior data should be cleared so the datalogger

only contains information on the machine it is now connected to. See page 3 for instructions on

clearing the data.

Instructions

17-3139-01.

Summary of content (18 pages)

PAGE 1
Instructions Installation and Operation of the TPDL1 Prodigy Smart-Board™ Datalogger Scotsman's Advanced Feature Smart-Board is an optional add on electronic device that can be applied to most Prodigy models.
PAGE 2
Use of Smart-Board Buttons: Scroll Up: Changes the display to a menu item higher on the menu list or goes up one number on a setting Scroll Down: Changes the display to a menu item lower on the menu list or goes down one number on a setting Select Button: Use to make changes to settings. Enter Button: Changes display to a sub menu list. Escape Button: Changes display to the main menu. Scroll Up Button Select Button Escape Button SmartBoard™ Advanced Feature Control 34 SEL ESC ENTER 02-4293-01 Rev A.
PAGE 3
Warnings - will appear in display after malfunction • • • • • Self Test Fail Long Freeze Pend Long Freeze Err Long Harvest Err Check Water • • • • • High Temp Error Sump Temp Sensor Disch Temp Sensor Min Freeze Pend Min Freeze Error • • • • Check Water Warn Long Freeze Warn Long Harv Warn High Temp Warn Communication Features: The datalogger can communicate information in two ways: • Display: The two line display is controlled by the buttons on the front of the datalogger.
PAGE 4
Tuesday level 1 Test Tuesday time 2 Water Test Tuesday level 2 Date - preset Water fill time Tuesday time 3 Time - preset to Central Time Esc to cancel test Tuesday level 3 Warnings Timers Tuesday time 4 No warnings Compressor run time Tuesday level 4 See prior page for warning list Comp resettable Wednesday time 1 Base Faults Press enter to reset Wednesday level 1 Fault code 1: Pwr up time Wednesday time 2 Fault code 2: Pwr resettable Wednesday level 2 Fault code 3: Press enter to reset Wednesday time 3 Fa
PAGE 5
Advanced Fault Definitions Self test failure The controller checks for proper operation at power up. If the check shows a problem, this warning or fault will be displayed. Long Freeze Pend If the ice machine fails to make ice within the maximum time limit, the controller will note that and display this warning or fault while it is attempting another freeze cycle.
PAGE 6
Smart-Board Button Use: Menu Groups: Push and release the down arrow key to scroll down to the next group.
PAGE 7
If there are no errors, the screen will display End of Errors. End of Errors Press and release the escape button to return to the main menu tree. Press and release the down arrow key to underline the A in Advanced Faults. ESC Base Faults Adv Faults Advanced Faults: Press and release the Enter button to see in the display: ENTER Most recent failure and the exact time it occurred. Pressing and releasing the down arrow cycles through the other failures back to the oldest.
PAGE 8
Press and release the down arrow to underline the S in Status. Status: Press and release the Enter button to see: Discharge Temp in degrees F., Then press and release the Down arrow key to see: Sump Temp in degrees F. Then press and release the Down arrow key to see: Adv Faults Status ENTER Discharge Temp: 157 Sump Temp: 38 Board Voltage - from the transformer. Then press and release the Down arrow key to see: Bin Level number. Use with Vari-Smart control. Displays level currently sensed.
PAGE 9
Pwr Interrupts: Number and time of power interruptions. Then press and release the Down arrow key to see: Pwr Interrupts: Bin Stat: Open or Closed. Open is normal when no bin thermostat is attached or there is no ice on a thermostat. Then press and release the Down arrow key to see: Bin Stat: Disch Frz Set: In degrees F. Shows the discharge temperature recorded as a set up number. The set up number is used for determining how long the fan is off at the end of the freeze cycle.
PAGE 10
Then push and release the Enter button to see: ENTER Performance Percent run time. Then press and release the Down arrow to see: Percent time run Min Freeze Time. Then press and release the Down arrow to see: Min Freeze Time 00:00 Max Freeze Time Max Freeze Time. Then press and release the Down arrow to see: 00:00 AVG Freeze Time AVG Freeze Time. Then press and release the Down arrow to see: 00:00 Min Harvest Time Min Harvest Time.
PAGE 11
Push and release the Down arrow to put the line under the T in Timers. Then press and release the Enter button to see: Test Timers Timers. Push and release the Enter button to see ENTER Compressor Run: Compressor run time. Then press and release the Down arrow to see: HR SEL Compressor run resettable. Press the Down arrow to go to the next line or Press SEL to enter reset mode.
PAGE 12
AFB Hardware Rev (Smart-Board revision) AFB Hardware Rev Then press and release the Down arrow to see: 1 Controller HW (hardware rev number). Controller HW 1 When done with Revisions, press and release the ESC button. ESC Revision Push and release the Down arrow to put the line under the S in Setup. Setup Then push and release the Enter button to see: ENTER Setup: View the Date or change it.
PAGE 13
Then press and release the Down arrow to view the Model number.
PAGE 14
Fill time warning. Then press and release the Down arrow to view the Fill time setpoint Freeze time warning. Then press and release the Down arrow to view the Freeze time warning setpoint Harvest time warning. Then press and release the Down arrow to view the warning Harvest time warning setpoint Discharge temp warning. Discharge temp warning setpoint Any of the above can be modified by changing the settings as noted below.
PAGE 15
Prodigy Software Installation and Use Description: The Scotsman Prodigy Tech Tool is a software program designed to access the datalogger tool. Requirements: • • • • Windows XP or Vista 40 MB disk space minimum. More will be needed if data logging is used. Desktop or Laptop PC with a USB port. Live ice machine with datalogger connected (to install USB driver) Software Installation: Pre-installation: The datalogger must be UNPLUGGED from the the PC. 1. Insert the CD into the computer’s CD-ROM drive. 2.
PAGE 16
Use: With the datalogger powered and connected to the computer's USB port, Open Scotsman Prodigy: Start, All Programs, Scotsman Prodigy, Prodigy Click on Get. The software will automatically begin to download the information from the Smart-Board. Once that is complete either click on Chart or select a new log file to review. When you click on Chart, the Column Selection dialog box will appear. You can select any chart you want to review. The default is all of them. Click on OK to go to the next step.
PAGE 17
Chart Definitions: • Freeze timer = Freeze time in seconds. • Harvest timer = Harvest time in seconds. • Freeze Counter = Continuous freeze cycles (starts over after bin full, power interruption, or • • • • • • • • • • • • • • • • • • • • • • • • • • • • • ice melt state) Flush level set point = Flush level setting 0-5. Flush used = 1-5. Flush level used in autoflush (0) mode.
PAGE 18
Reference Example of generated PDF file Error Code Display Op Mode Display