Use and Care

ManualsBrandsScotsman ManualsShop All ScotsmanScotsman 200 lb., Countertop Ice Dispenser

INTRODUCTION

This service manual is intended as a reference for

the installer, user, and service agent of this

Scotsman ice dispenser. It includes the necessary

information to install, start up, operate, clean and

maintain this unit.

This manual contains important information, read it before beginning installation or operation.

Keep it for future reference.

ID150, ID200, ID250

May 2002

Page 1

Table of Contents

INTRODUCTION · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 1

SPECIFICATIONS · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 2

FOR THE INSTALLER · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 3

INSTALLATION · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 4

WATER GLASS FILLER KIT · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 5

WATER GLASS KIT - CONTINUED · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 6

ICE DIVERTER KIT · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 7

INITIAL START UP · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 8

GATE RESTRICTOR PLATE · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 9

CLEANING AND SANITIZING · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 10

CLEANING AND SANITIZING · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 11

TROUBLESHOOTING · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · Page 12

Summary of content (12 pages)

PAGE 1
ID150, ID200, ID250 INTRODUCTION This service manual is intended as a reference for the installer, user, and service agent of this Scotsman ice dispenser. It includes the necessary information to install, start up, operate, clean and maintain this unit.
PAGE 2
ID150, ID200, ID250 SPECIFICATIONS The ID ice dispenser is a machine that stores manually filled ice in an insulated, sanitary container; upon demand it dispenses that ice into a cup or glass. NOTE: This ice stand is designed to dispense cubed ice only. Flaked ice will not work. Scotsman reserves the right to make design changes and/or improvements at any time. Specifications and designs are subject to change without notice.
PAGE 3
ID150, ID200, ID250 FOR THE INSTALLER This ice dispenser has been specifically designed to provide protection against personal injury and eliminates contamination of ice. To ensure continued protection and sanitation, observe the following: · ALWAYS: disconnect power to the dispenser DESCRIPTION Designed to be manually filled with ice from any remote ice-making source, these dispensers will dispense cubes (up to 1-1/4” in size), cubelets and hard-chipped or cracked ice.
PAGE 4
ID150, ID200, ID250 INSTALLATION 1. Locate the ice dispenser on the counter. Allow vertical clearance above unit for the removal of the cover, and for pouring ice into the hopper. 2. Plan the unit drain. A 1” I.D. drain tube is required for draining. Routing is either thru the back or base. Sufficient fittings are included with the unit to install in most cases. 3.
PAGE 5
ID150, ID200, ID250 WATER GLASS FILLER KIT Installation Instructions WARNING: Disconnect power to unit before proceeding with installation 1. Prepare unit as follows: · Remove lower front panel. · Locate new holes in front panel. 2. Install faucet and tubing assembly as shown below. 3. Connect field water supply to ¼ male flare fitting on tubing assembly. Apply water pressure and check all connections for leaks. Check faucet for proper operation.
PAGE 6
ID150, ID200, ID250 WATER GLASS KIT - CONTINUED ID150 A 4” B 2.5” ID200, ID250 A 6 1/8” B 3 1/8” Water inlet can be routed either from the back or from underneath the dispenser. If from the back, remove the back and bottom access panels. If from below, only remove the bottom access panel. A hole is not needed at the intersection of C and D, unless the back access panel is retained.
PAGE 7
ID150, ID200, ID250 ICE DIVERTER KIT NOTE: For dispensing Scotsman Nugget Ice: Note: The agitation timer must be adjusted to the MINIMUM position when dispensing nugget ice. 1. Disconnect power to dispenser. 2. Remove Merchandiser from dispenser. 3. Remove ice chute and discard gate restrictor. 4. Install ice diverter on gate mounting plate as shown below. 5. Apply RTV to back surface of ice diverter, to seal to gate mounting plate. 6. Reinstall gasket and ice chute.
PAGE 8
ID150, ID200, ID250 INITIAL START UP 1. Sanitize the ice storage system as instructed on page 11. 2. Fill hopper with sanitary ice. 3. Plug the unit’s power cord into an electrical outlet and the lighted sign should come on. Dispense several containers of ice. In normal operation, pushing the ice dispenser mechanism will cause ice to flow from the ice chute. Ice flow will continue until the dispenser mechanism is released. CAUTION: Use caution to avoid spilling ice when filling dispenser.
PAGE 9
ID150, ID200, ID250 GATE RESTRICTOR PLATE CAUTION: Disconnect power to dispenser before installing, removing or adjusting restrictor. ADJUSTMENT This plate may be adjusted as shown to reduce or increase the dispensing rate of ice, especially desirable when using glasses or other containers with small openings. Adjustment can be made by sliding up or down with nuts loosened, to obtain the desired amount of restriction.
PAGE 10
ID150, ID200, ID250 CLEANING AND SANITIZING The sink, grill and splash panel area should be cleaned daily. The following dispenser maintenance should be performed at the intervals indicated: DAILY (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. WEEKLY (or as required) Clean vending area. Check for proper water drainage from the vending area drip tray. MONTHLY Clean and sanitize the hopper interior (see CLEANING INSTRUCTIONS).
PAGE 11
ID150, ID200, ID250 CLEANING AND SANITIZING MONTHLY & INITIAL START UP: 11. Using a mechanical spray bottle filled with sanitizing solution, spray the inside of the ice chute. Allow to air dry. Sanitize the Ice Storage System. Note: this should only be done by qualified personnel. 12. Reinstall merchandiser. CLEANING PRECAUTIONS 13. Wipe the top edge of the ice hopper with the sanitizing solution, allow to air dry.
PAGE 12
ID150, ID200, ID250 TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check the following chart under the appropriate symptoms to aid in locating the defect. Trouble Probable Cause BLOWN FUSE OR CIRCUIT BREAKER. A. Short circuit in wiring. B. Defective gate solenoid. C. Defective agitator motor.