ITEM #1390703 3-LIGHT PENDANT MODEL #CPS44MBK Français p. 12 Español p. 23 ATTACH YOUR RECEIPT HERE For Damp Location Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.
TABLE OF CONTENTS Package Contents ................................................................................................................3 Hardware Contents ...........................................................................................................................4 Safety Information ................................................................................................................4 Preparation ...........................................................................
PACKAGE CONTENTS A B C D F E G PART A B C D E F G H I J K DESCRIPTION QUANTITY Mounting Strap Hex Nut (preassembled to threaded rod (C)) Threaded Rod (preassembled to mounting strap (A)) Canopy Screw Collar Loop (preassembled to threaded rod (C)) Threaded Ring (preassembled to screw collar loop (E)) Chain Fixture Loop (preassembled to fixture (J)) Frame Fixture (preassembled to frame (I)) Socket cover 1 2 H 1 I 1 1 K 1 1 1 1 1 3 3 J
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 CC Connecting Chain Link Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal.
SAFETY INFORMATION WARNING • To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp edges. • DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to a mounting strap which is first attached to the outlet box. Wire connectors will not support the weight of a fixture.
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. 1 DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. 2. Remove existing fixture and disconnect all electrical wiring. 2 3. Attach mounting strap (A) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (BB).
ASSEMBLY INSTRUCTIONS 4. Remove threaded ring (F) from screw collar loop (E) and save for later use. 4 Temporarily place canopy (D) over mounting strap (A) to determine amount of adjustment necessary for threaded rod (C). NOTE: Canopy (D) should fit flush against ceiling when mounted. Once threaded rod (C) is adjusted, tighten hex nuts (B) securely against mounting strap (A). A B C C D E Set canopy (D) aside. E F 5.
ASSEMBLY INSTRUCTIONS 6. Locate connecting chain links (CC) in hardware pack and open both of them. Attach one connecting chain link (CC) to fixture loop (H) at the top of the frame (I) and then attach one end of the chain (G) to the connecting chain link (CC). Close this connecting chain link (CC). 64 G CC Hook the other connecting chain link (CC) to the screw collar loop (E) at the bottom of threaded rod (C) on mounting strap (A)--leave this connecting chain link (CC) open for now.
ASSEMBLY INSTRUCTIONS 9a. Feed wiring through hole at bottom of threaded rod (C). Gently push wiring until it comes through top of threaded rod (C). Pull all wiring until there is no extra slack left in the wires running through the chain (G). 9a C Prepare wire by stripping 1/2 in. of insulation from wire ends using wire strippers (not included). Wiring 9b. Connect SMOOTH wire from fixture (J) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 10. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. Push wire connectors (AA) gently back into outlet box. Carefully push excess wiring into outlet box. 10 Outlet Box AA WARNING: Make sure no bare wire or wire strands are visible after making connections. AA 11. Slide canopy (D) and threaded ring (F) up the chain (G). Secure canopy (D) to mounting strap (A) by tightening the threaded ring (F) to screw collar loop (E).
CARE AND MAINTENANCE • Shut off main power supply. Wipe with soft cloth or use window cleaner. Do not use an abrasive cleaner. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb(s) will not light. POSSIBLE CAUSE 1. Bulb(s) is/are burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace light bulb(s). 2. Make sure power supply is ON. 3. Check wiring and all connections. Fuse blows out or circuit breaker trips. 1.