ITEM #1411947 PENDANT MODEL #CPSL3SG Français p. 12 Español p. 23 ATTACH YOUR RECEIPT HERE APPROVED FOR USE IN DAMP LOCATIONS Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.
TABLE OF CONTENTS Package Contents ................................................................................................................3 Hardware Contents ...........................................................................................................................4 Safety Information ................................................................................................................4 Preparation ...........................................................................
PACKAGE CONTENTS A x 32 B x 64 C x 64 D x 64 E PART DESCRIPTION A B Fixture Glass Rod A C Glass Rod A+ D Glass Rod B E Glass Rod C F Glass Rod D QUANTITY 1 32 + 2 extra 64 + 2 extra 64 + 2 extra 64 + 2 extra 32 + 2 extra 3 x 32 F
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 CC DD Mounting Strap (with hex nuts) Qty. 1 EE FF Safety Cable Finial Green Ground Screw Qty. 1 Qty. 1 Qty. 1 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product.
SAFETY INFORMATION DANGER • DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white neutral house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will receive electrical shock, which could cause serious injury or death.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 90 minutes Tools Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, wire strippers, pliers, wire cutters, safety glasses, stepladder, electrical tape.
ASSEMBLY INSTRUCTIONS 3. Insert GREEN ground screw (FF) in mounting strap (CC). 3 CC Hardware Used CC Mounting Strap* (*not to scale) x1 Threaded Rod FF Green Ground Screw x1 4. Remove tie on each cord on fixture (A) to allow cords to extend completely.
ASSEMBLY INSTRUCTIONS 5. Attach mounting strap (CC) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. 5 Outlet Box Tighten machine screws (BB) to secure mounting strap (CC) to outlet box. CC Washer CAUTION: Make sure the outlet box can support 35 lbs. hanging weight.
ASSEMBLY INSTRUCTIONS 7. Attach safety cable (DD) to mounting strap (CC) using clip on other end. 7 DD Outlet Box Determine the hanging length that is best for the fixture (A). CC If you wish to change cord length, loosen (but do not remove) plastic piece preassembled on one of the cords on inside of canopy. Plastic Piece Adjust cord to desired hanging length by pushing metal collar toward underside of canopy.
ASSEMBLY INSTRUCTIONS 9. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. 9 WARNING: Make sure no bare wire or wire strands are visible after making connections. AA AA AA Carefully arrange excess wiring and wire connectors (AA) within canopy of fixture (A). Hardware Used AA Wire Connector x3 10. Align hole in middle of canopy with threaded rod in mounting strap (CC). Secure canopy with finial (EE).
ASSEMBLY INSTRUCTIONS 12. Restore power and test fixture (A). 12 If light does not function, please refer to the TROUBLESHOOTING below. A CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. • Total wattage for this fixture is 27 watts; do not attempt to replace the LEDs. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock.