ITEM #1341889 5-LIGHT ISLAND LIGHT MODEL #ILS5BNK Français p. 12 Español p. 23 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-527-1292, 8:30 a.m. - 5 p.m.
TABLE OF CONTENTS Package Contents ................................................................................................................. 3 Hardware Contents ............................................................................................................... 4 Safety Information ................................................................................................................. 4 Preparation ..................................................................................
PACKAGE CONTENTS A C B F E G H D PART DESCRIPTION QUANTITY A Mounting Plate (preassembled to canopy (B)) 1 B Canopy 1 C Mounting Plate Screw (preassembled to canopy (B)) 2 D Fixture 1 E 6-inch Rod 4 F 12-inch Rod 8 G Nut (preassembled to 6-inch Rod (E)) 2 H Lock Washer (preassembled to 6-inch Rod (E)) 2 3
HARDWARE CONTENTS (shown actual size) AA Wire Connector Qty. 3 BB Machine Screw Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
SAFETY INFORMATION WARNING • DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting plate which is first attached to the outlet box. Wire connectors will not support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or fire.
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. 1 DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. 2. Remove existing fixture and disconnect all electrical wiring. ON ON OFF OFF 2 3. Remove mounting plate (A) from canopy (B) by removing mounting plate screws (C) from the edges of the canopy (B). 3 A Save mounting plate screws (C) for later use.
ASSEMBLY INSTRUCTIONS 4. Attach mounting plate (A) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. 4 Outlet Box Tighten machine screws (BB) completely to secure mounting plate (A) to outlet box.
ASSEMBLY INSTRUCTIONS 5b. If you wish to use the fixture (D) with fewer rods or a combination of both rod sizes, decide which rods (E and F) will be used. Remove nut (G) and lock washer (H) from top of 6-inch rods (E). Feed wires from fixture (D) through predeterminded rods (E/F) - Make sure wires do not get twisted. Secure all 6-inch rods (E) and 12-inch rods (F) by screwing the ends of each one together. Be sure rods are completely connected.
ASSEMBLY INSTRUCTIONS 7. Connect BARE/GREEN ground wire from outlet box to BARE wire from mounting plate (A) using wire connector (AA). Connect WHITE wire from fixture (D) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLACK wire from fixture (D) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 8. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. Push wire connectors (AA) gently back into outlet box. Carefully push excess wiring into outlet box. 8 Outlet Box AA WARNING: Make sure no bare wire or wire strands are visible after making connections. AA AA 9. Align holes in edge of canopy (B) with holes on edge of mounting plate (A).
CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb(s) will not light. POSSIBLE CAUSE 1. Bulb(s) is/are burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace light bulb(s). 2. Make sure power supply is ON. 3. Check wiring and all connections.