User's Manual

Page 29 of 36
P/N 595289-01 Rev B 5/15
CLASS B DIGITAL DEVICE
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE
FCC Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, Including interference that
may cause undesired operation.
FCC Warning (Part 15.21)
Changes or modications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
This portable transmitter with its antenna complies with FCC/IC RF exposure limits for
general population / uncontrolled exposure.
The X3 SEMS II Control Console Transmitter has been assigned
FCC ID:T5E201122 / The X3 SEMS II with BLUETOOTH Control Console Trans-
mitter has been assigned FCC ID: T5E201122A
SAFETY LISTINGS
CAUTION
DO NOT USE A FIBERGLASS WRAPPED
ONE HOUR CYLINDER ON A MODEL 4.5
AIR-PAK EQUIPPED WITH A PAK-ALERT DIS-
TRESS ALARM AS THE WEIGHT WILL EXCEED
THE 35 LBS APPROVAL LIMIT FOR SCBA’S
ESTABLISHED BY NIOSH.
INDUSTRY CANADA COMPLIANCE
Industry Canada Statement
The term “IC” before the certication / registration number only signies that the In-
dustry Canada technical specications were met.
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed
such that it does not emit RF eld in excess of Health Canada limits for the general
population. Consult Safety Code 6, obtainable from Health Canada’s web site: www.
hc-sc.gc.ca/rpb.
This Device complies with Industry Canada License-exempt RSS standard(s). Opera-
tion is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that
may cause undesired operation of the device.
IC ID: 6453A-201122 / 6453A-201122A
LA DÉCLARATION DE CANADA D'INDUSTRIE
L' « IC » de terme avant que la certication/le nombre d'enregistrement signie seule-
ment que le Canada d'Industrie spécications techniques ont été rencontrées.
Sectionner 14 de RSS-210
Le programme d'installation de cet équipement de radio doit garantir que l'antenne
est localisée ou tel est indiqué qu'il n'émet pas le champ de RF dépassant les limites
de Canada de Santé pour la population générale. Consulter le Code de Sécurité 6,
procurable du site Web de Canada de Santé : www.hc-sc.gc.ca/rpb.
Cet appareil est conforme aux normes Industry Canada exemptes de licence RSS
standard(s). L'opération est assujetti au suivre deux conditions :
1) cet appareil ne peut pas causer l'intervention, et
2) cet appareil doit accepter de l'intervention, y compris l'intervention
qui peut causer l'opération non désirée de l'appareil.
IC ID: 6453A-201122 / 6453A-201122A